FS: Barely Used Corvette Mods Low Beam HID Set 6000K 35W
08-02-2014, 05:21 PM
#1
Melting Slicks
Thread Starter
Member Since: Sep 2012
Location: LaGrange Park, IL IL
Posts: 2,308
Received 158 Likes
on
131 Posts
St. Jude Donor '13, '15
FS: Barely Used Corvette Mods Low Beam HID Set 6000K 35W
Just bought an ACA projector setup from a fellow forum member and will be selling my current low beam light set soon. Wanted to get this out there early to find a buyer. They are currently still on the car and likely will be another 1-2 weeks before I can remove when I install the new set.
Corvette Mods Low Beam HID kit. Includes two 35w ballasts and two 6000k bulbs. These bulb are mostly white, with a slight blue tint. I bought these new about a year ago and will say hardly ever used them. Lots of life in this setup. Optional resistor not included.
Asking $55 + shipping. Paypal accepted. Located in Chicago. These are $70 + shipping new from Corvette Mods.
I don't have any nighttime pictures. Below is all I currently have of them...Let me know if you have any questions. Thank you for looking.
Corvette Mods Low Beam HID kit. Includes two 35w ballasts and two 6000k bulbs. These bulb are mostly white, with a slight blue tint. I bought these new about a year ago and will say hardly ever used them. Lots of life in this setup. Optional resistor not included.
Asking $55 + shipping. Paypal accepted. Located in Chicago. These are $70 + shipping new from Corvette Mods.
I don't have any nighttime pictures. Below is all I currently have of them...Let me know if you have any questions. Thank you for looking.
Last edited by imgn tht; 08-05-2014 at 08:25 PM.
08-05-2014, 09:22 AM
#6
Melting Slicks
Thread Starter
Member Since: Sep 2012
Location: LaGrange Park, IL IL
Posts: 2,308
Received 158 Likes
on
131 Posts
St. Jude Donor '13, '15
Sorry I would need more than that...
I'll try to get nighttime pics and post here. They are plug and play. You disconnect the factory halogen bulb from OEM harness, plug in the 35w ballast to the OEM side, then add the new HID bulb to the other side of the ballast. You may need some sort of 3M body tape to mount the ballast in your desired location. Zip ties also work. I used both and mounted the ballast on the fender liner just under the headlamp.
Almost forgot, you *might* need a resistor to make the headlight buckets open and close properly. Some folks need it, and others do not. I did need it, and will be keeping the resistor I have to operate the new ACA setup. These can be purchased cheap through some of the forum vendors.
Almost forgot, you *might* need a resistor to make the headlight buckets open and close properly. Some folks need it, and others do not. I did need it, and will be keeping the resistor I have to operate the new ACA setup. These can be purchased cheap through some of the forum vendors.
Last edited by imgn tht; 08-05-2014 at 09:28 AM.
08-06-2014, 12:03 AM
#7
Melting Slicks
Thread Starter
Member Since: Sep 2012
Location: LaGrange Park, IL IL
Posts: 2,308
Received 158 Likes
on
131 Posts
St. Jude Donor '13, '15
No lights at all looking out my garage
OEM Halogen high beams only which should give you a good comparison to the HID low beams
HID low beams only
After they have warmed up a few seconds
Don't mind the passenger DRL unlit in that last pic. Waiting for the switchbacks to be off backorder to get my replacement.
