FS: Borla stinger quad tip and ARH 3in xpipe with cutouts
#1
Instructor
Thread Starter
ARH 3in xpipe with cutouts
I have a ARH x with cutouts I just removed. borla was posted but it sold.
I went back to my kooks xpipe I had laying around and just replaced the borla with corsa extreme.
Now the run down of the cutouts.
I purchased this xpipe for 400 bucks back in February this year. When I got it needed work which I knew of. I got all new hardware (bolts and stainless exhaust clamps that it did not have). I ordered two new cutout motors, switch and harness. Total of 700 bucks spent counting the 400 for the xpipe.
The other day I flipped the switch and cutouts got stuck open. My car makes almost 1k to the tire and the last thing I have time for is to keep messing with the exhaust. When this happened I purchased corsa extreme the next day. So far the corsa lands between the cutouts open and the borla which makes me happy.
I noticed one of the set screws on the exhaust cutout backed out causing it to get stuck. I just removed it all and want to sell. I don’t have time to keep messing with it. The harness took almost two months to get as they were on back order earlier this year.
I will do 500 shipped for the xpipe and everything I have (all bolts, clamps, cutouts, console piece and wiring harness). I will even include my center console piece I cut up to mount the exhaust switch so you don’t have to cut yours up. I already have another I purchased for 35.00 bucks not cut up.
Also you have to have kooks or arh long tubes for the xpipe to work.
Text or call 812-344-7144, if I don’t answer I’ll call ya back soon as I can. Shoot me a text if I don’t answer.
I went back to my kooks xpipe I had laying around and just replaced the borla with corsa extreme.
Now the run down of the cutouts.
I purchased this xpipe for 400 bucks back in February this year. When I got it needed work which I knew of. I got all new hardware (bolts and stainless exhaust clamps that it did not have). I ordered two new cutout motors, switch and harness. Total of 700 bucks spent counting the 400 for the xpipe.
The other day I flipped the switch and cutouts got stuck open. My car makes almost 1k to the tire and the last thing I have time for is to keep messing with the exhaust. When this happened I purchased corsa extreme the next day. So far the corsa lands between the cutouts open and the borla which makes me happy.
I noticed one of the set screws on the exhaust cutout backed out causing it to get stuck. I just removed it all and want to sell. I don’t have time to keep messing with it. The harness took almost two months to get as they were on back order earlier this year.
I will do 500 shipped for the xpipe and everything I have (all bolts, clamps, cutouts, console piece and wiring harness). I will even include my center console piece I cut up to mount the exhaust switch so you don’t have to cut yours up. I already have another I purchased for 35.00 bucks not cut up.
Also you have to have kooks or arh long tubes for the xpipe to work.
Text or call 812-344-7144, if I don’t answer I’ll call ya back soon as I can. Shoot me a text if I don’t answer.
Last edited by HarbaughFRC; 07-15-2019 at 08:50 AM. Reason: Sold borla
#2
Instructor
Thread Starter
Photos added. Exhaust has no dings or dents. Tips are polished and I always kept the bottom inside polished that you can see. Requires work to keep them this nice as I wipe them down every time after driving the car. Borla is packed and ready to be shipped.
on the xpipe photos you can see in two photos where the set screw is backed out and stuck. Also included photos of the harness and switch panel that goes with.
on the xpipe photos you can see in two photos where the set screw is backed out and stuck. Also included photos of the harness and switch panel that goes with.