**Group Buy - CARBON C5 Rear Diffusers**
#1
Former Vendor
Thread Starter
**Group Buy - CARBON C5 Rear Diffusers**
I'm going to start by saying, we NEED to have a minimum of 10 people committed and paid in full for this to begin. I promise you once we get the number we need it will be a very fast process (2-3 weeks) These are being made by my new manufacturer that made the urethane diffuser posted below. These will fit perfect just like the urethane version, and are made in the USA.
I'm sure most of you have seen the other threads, but to make it easy, I'm using the same info.
Well, its FINALLY happened!! We are happy to unveil our new diffusers for the C5 Corvette. It's been years in the making as most of you know and after countless broken promises from a previous manufacturer, we finally got these finished.
These will be made out of real carbon, not an overlay. Mounting is very simple, there are four tabs on the back side, those you slide into the rear vents on the bumper and that will guide it into place. Once it's somewhat lined up you can adjust it as needed. You may also want to use a soapy solution and spray the rear bumper to give you a few seconds to move the diffuser around before the tape gets tacky. It's as simple as tightening down the nuts, then doing the same on the lower fin that goes under the fender. There are also 4 tabs that bolt on using your existing bolts above your exhaust. You'll see once it's in your hands, it's very straight forward, no need to pay someone to install it for you. It will include the hardware you need to mount it, which will be some washers and nuts (inserts are molded into it already) We don't provide the double sided tape that is recommended, but I'll post an email address to a guy that I have sent a lot of customer to, he has great prices and ships fast.
Here's his email address jwilson4940@gmail.com just tell him you need 3M VHB and the length you want (also tell him Pete sent you). I would think 6 feet should be enough.
I made sure manufacturing knew that these had to fit really well, and he said they nailed it. They have a C5 rear clip, as you'll see in the pictures at their facility that they used for mock up and test fitting. I'm confident that you guys will be very pleased with these. A lot of work by a lot of people have gone into this. Special thanks to Rob (Stealth02) for his work in getting the prototype made and sent to us, for that we are calling it the Stealth C5 diffuser.
Pricing is as follows:
$749 + 79 shipping anywhere in the lower 48 states, please pm me if you need shipping internationally or to Canada.
After the GB is over, these will go up to $799 + Shipping.
Here's a video of the diffuser and pictures
Here is a customer that purchased the urethane version and mocked it up to get some quick pics. You can see he was pleased with the results
Group Buy List
1.doublec4 - Paid
2.jumpinmeanz - Paid
3.Z06WHO - Paid
4.shawn - Paid
5.
I'm sure most of you have seen the other threads, but to make it easy, I'm using the same info.
Well, its FINALLY happened!! We are happy to unveil our new diffusers for the C5 Corvette. It's been years in the making as most of you know and after countless broken promises from a previous manufacturer, we finally got these finished.
These will be made out of real carbon, not an overlay. Mounting is very simple, there are four tabs on the back side, those you slide into the rear vents on the bumper and that will guide it into place. Once it's somewhat lined up you can adjust it as needed. You may also want to use a soapy solution and spray the rear bumper to give you a few seconds to move the diffuser around before the tape gets tacky. It's as simple as tightening down the nuts, then doing the same on the lower fin that goes under the fender. There are also 4 tabs that bolt on using your existing bolts above your exhaust. You'll see once it's in your hands, it's very straight forward, no need to pay someone to install it for you. It will include the hardware you need to mount it, which will be some washers and nuts (inserts are molded into it already) We don't provide the double sided tape that is recommended, but I'll post an email address to a guy that I have sent a lot of customer to, he has great prices and ships fast.
Here's his email address jwilson4940@gmail.com just tell him you need 3M VHB and the length you want (also tell him Pete sent you). I would think 6 feet should be enough.
I made sure manufacturing knew that these had to fit really well, and he said they nailed it. They have a C5 rear clip, as you'll see in the pictures at their facility that they used for mock up and test fitting. I'm confident that you guys will be very pleased with these. A lot of work by a lot of people have gone into this. Special thanks to Rob (Stealth02) for his work in getting the prototype made and sent to us, for that we are calling it the Stealth C5 diffuser.
Pricing is as follows:
$749 + 79 shipping anywhere in the lower 48 states, please pm me if you need shipping internationally or to Canada.
After the GB is over, these will go up to $799 + Shipping.
Here's a video of the diffuser and pictures
Here is a customer that purchased the urethane version and mocked it up to get some quick pics. You can see he was pleased with the results
Group Buy List
1.doublec4 - Paid
2.jumpinmeanz - Paid
3.Z06WHO - Paid
4.shawn - Paid
5.
Last edited by Quik Z06; 05-20-2016 at 05:58 AM.
The following users liked this post:
jbclutch (05-20-2016)
#3
Former Vendor
Thread Starter
#12
Former Vendor
Thread Starter
#13
Former Vendor
Thread Starter
Ok guys, GOOD NEWS!!
I spoke to manufacturing, and have been pestering them about getting carbon done, and as mentioned they originally wanted a minimum. Well I've talked them into doing this regardless of minimums. What does that mean? It means this is going to get started most likely next week. From there it's only 2-3 weeks until we have carbon diffusers in our hands.
I know a lot of guys reached out via pm and were worried about putting money down then having to wait to see if they would even be made, well that is not the case anymore. Now when you get your order in, it will be shipped in about 3 weeks. These will be the same quality as the urethane and will have the same precise fitment.
With that said guys, who's in for a carbon C5 Diffuser??
I spoke to manufacturing, and have been pestering them about getting carbon done, and as mentioned they originally wanted a minimum. Well I've talked them into doing this regardless of minimums. What does that mean? It means this is going to get started most likely next week. From there it's only 2-3 weeks until we have carbon diffusers in our hands.
I know a lot of guys reached out via pm and were worried about putting money down then having to wait to see if they would even be made, well that is not the case anymore. Now when you get your order in, it will be shipped in about 3 weeks. These will be the same quality as the urethane and will have the same precise fitment.
With that said guys, who's in for a carbon C5 Diffuser??
The following users liked this post:
mtndv8 (05-27-2016)
#14
Pro
#16
Former Vendor
Thread Starter
I have 3 paid orders so far, and 2-3 pm's out there pending. I will allow those guys to get on board. However, pricing will have to go back up to $799 + $79 shipping in about 2 weeks. After that you'll no longer see these at $749.
Last edited by Quik Z06; 05-19-2016 at 10:48 PM.
#19
Former Vendor
Thread Starter
#20
Pro