C6 Corvette General Discussion General C6 Corvette Discussion not covered in Tech
Sponsored by:
Sponsored by:

Take Care of Your Clutch--Preventing or Curing Pedal Issues

Thread Tools
 
Search this Thread
 
Old 02-13-2009, 04:54 PM
  #21  
cthusker
Le Mans Master
 
cthusker's Avatar
 
Member Since: Dec 2005
Location: North Western Connecticut
Posts: 7,594
Received 91 Likes on 54 Posts

Default

Excellent! Very informative and great advice! I've been following this procedure ever since Ranger explained this situation quiet awhile ago.... Thanks again!!
Old 02-13-2009, 05:23 PM
  #22  
Migs08
Racer
 
Migs08's Avatar
 
Member Since: Feb 2008
Location: Texas
Posts: 485
Likes: 0
Received 1 Like on 1 Post
Default

Terrific video!

Now if only someone could make a video on paddle shifter maintenance for us A6 owners...
Old 02-13-2009, 06:58 PM
  #23  
Marina Blue
Burning Brakes
 
Marina Blue's Avatar
 
Member Since: Feb 2005
Location: Whitehall PA
Posts: 1,113
Likes: 0
Received 8 Likes on 4 Posts

Default

Ranger,

Good to hear from you and appreciate your efforts. I have been using this procedure ever since you first posted and have had no problems for over three years. Few would investigate the root cause as you have and then so unselfishly share the results for all to see. Great job and thanks again.
Old 02-13-2009, 07:31 PM
  #24  
Vette junkie
Burning Brakes
 
Vette junkie's Avatar
 
Member Since: Jan 2005
Location: Plymouth MI
Posts: 821
Likes: 0
Received 170 Likes on 69 Posts

Default

Originally Posted by Ranger
Hi Vette junkie,

The MixMizer can be found at Walmart, typically on a pegboard near the gas cans in automotive. Costs about $3. I've used the same one for 8 years.

Ranger
Thanks much. I'm off to Wally World to pick one up. Great job on the video by the way. There's not a time that I log on and don't come away smarter.
Old 02-14-2009, 07:45 AM
  #25  
Ranger
Race Director
Support Corvetteforum!
Thread Starter
 
Ranger's Avatar
 
Member Since: Aug 2000
Location: Central Florida
Posts: 10,649
Likes: 0
Received 26 Likes on 20 Posts

Default

Appreciate the testimonials to the protocol and the all generous words sent my way.

Originally Posted by Marina Blue
Ranger,

Good to hear from you and appreciate your efforts... Few would investigate the root cause as you have and then so unselfishly share the results for all to see. Great job and thanks again.
Hi Marina Blue.

I tried to stay on the case until the root cause was identified. We were fortunate the the lab director at Unovis, a C6Z owner BTW, took a personal interest in the issue. Once the electron microscope was brought to bear, iron and copper in their elemental forms turned up in clutch fluid that had just a few miles of very aggressive launch and shift driving. Analysis matched them exactly to the samples of dust from the same vehicle's clutch disc. A second sample from a different car produced identical results. Mystery solved.

We can hope that GM will over time do some redesign work on the clutch hydraulics to reduce or eliminate the infusion of clutch dust into the fluid. But given GM's financial situation, we may be waiting a while. In the meantime, we have a preventative protocol that works and it's not much bother.

Best regards,

Ranger
Old 02-14-2009, 08:25 AM
  #26  
C6~Missle
Le Mans Master
 
C6~Missle's Avatar
 
Member Since: Aug 1999
Location: N Carolina 08 Z51 Coupe
Posts: 5,411
Likes: 0
Received 1 Like on 1 Post

Default

Thanks Ranger.. I've been doing this ever since I saw your post a long time back... Great video... Appreciate the effort...
Old 02-14-2009, 08:28 AM
  #27  
NormWild
Drifting
 
NormWild's Avatar
 
Member Since: Apr 2008
Location: Lehigh Valley Pennsylvania
Posts: 1,955
Received 20 Likes on 17 Posts

Default

Thanks again Ranger, did mine yesterday as it continues to sit in the garage for winter It took me longer to run and get the GM Clutch fluid than it did to fill and flush the reservoir three times. Fluid was pretty dark and low at first, now nice and clear.
Old 02-14-2009, 12:42 PM
  #28  
BenThere
Team Owner
 
BenThere's Avatar
 
Member Since: Aug 2008
Location: Chandler, AZ It's a Dry Heat.
Posts: 21,993
Received 2 Likes on 2 Posts

Default

I just watched the video again (can't get the sound to work, but that's probably my problem) and I notice that you are also a role model for safety by not futzing with the Nav while driving!

Anyway, one more time, thanks, and as posted above, special thanks for sharing so freely and unselfishly. Amazing what results from passion.
Old 02-14-2009, 12:57 PM
  #29  
need-for-speed
Team Owner
 
need-for-speed's Avatar
 
Member Since: Feb 2000
Location: Conroe Texas
Posts: 35,254
Received 865 Likes on 608 Posts
CI 1-4-5-8-9-10 Vet
St. Jude Donor '03,'04,'05,'07,08,'09,'10,’17

Default

Any recommendations on which fluid to buy ? (prefer something available at Wally World or local auto parts).
Old 02-14-2009, 01:02 PM
  #30  
Ranger
Race Director
Support Corvetteforum!
Thread Starter
 
Ranger's Avatar
 
Member Since: Aug 2000
Location: Central Florida
Posts: 10,649
Likes: 0
Received 26 Likes on 20 Posts

Default

Originally Posted by need-for-speed
Any recommendations on which fluid to buy ? (prefer something available at Wally World or local auto parts).
Prestone DOT4, shown in the video at 3:22, is available at most Walmart stores for about $2.60 per 12 ounce cans. If your clutch fluid is very dark, buy two cans. Otherwise one will do. I've used that fluid interchangeably with the GM-brand. No issues with mixing them.

Ranger
Old 02-14-2009, 01:03 PM
  #31  
need-for-speed
Team Owner
 
need-for-speed's Avatar
 
Member Since: Feb 2000
Location: Conroe Texas
Posts: 35,254
Received 865 Likes on 608 Posts
CI 1-4-5-8-9-10 Vet
St. Jude Donor '03,'04,'05,'07,08,'09,'10,’17

Default

p.s. I have a question:

I do not doubt Ranger's theory because the consensus seems to be unanimous. But I am curious - I assume the hydraulic clutch circuit is a sealed system with a piston actuating components on the south end - all sealed.

How does clutch dust get into the fluid ?
Old 02-14-2009, 01:05 PM
  #32  
need-for-speed
Team Owner
 
need-for-speed's Avatar
 
Member Since: Feb 2000
Location: Conroe Texas
Posts: 35,254
Received 865 Likes on 608 Posts
CI 1-4-5-8-9-10 Vet
St. Jude Donor '03,'04,'05,'07,08,'09,'10,’17

Default

Originally Posted by Ranger
Prestone DOT4, shown in the video at 3:22, is available at most Walmart stores for about $2.60 per 12 ounce cans. If your clutch fluid is very dark, buy two cans. Otherwise one will do. I've used that fluid interchangeably with the GM-brand. No issues with mixing them.

Ranger

Thanks Ranger Next time I'll RTFM

I was planning on watching that video tonight while "kicking back" with a cold one. I'm on my way to Wally's now for other stuff and will pick up the components.

edit: holy **** !! I just looked at mine

bought the car new and it only has 4800 miles



I'll be buying TWO cans ........

Last edited by need-for-speed; 02-14-2009 at 01:11 PM.
Old 02-14-2009, 01:16 PM
  #33  
Tzzird
Burning Brakes
 
Tzzird's Avatar
 
Member Since: Aug 2005
Location: LA CA
Posts: 1,025
Likes: 0
Received 0 Likes on 0 Posts

Default

Originally Posted by need-for-speed
Thanks Ranger Next time I'll RTFM

I was planning on watching that video tonight while "kicking back" with a cold one. I'm on my way to Wally's now for other stuff and will pick up the components.

edit: holy **** !! I just looked at mine

bought the car new and it only has 4800 miles



I'll be buying TWO cans ........
You must be in the population of vette owners that run theirs at the limit more often than they should.

Mine was just as bad just as early.
Old 02-14-2009, 01:23 PM
  #34  
Ranger
Race Director
Support Corvetteforum!
Thread Starter
 
Ranger's Avatar
 
Member Since: Aug 2000
Location: Central Florida
Posts: 10,649
Likes: 0
Received 26 Likes on 20 Posts

Default

Originally Posted by need-for-speed
...I assume the hydraulic clutch circuit is a sealed system with a piston actuating components on the south end - all sealed.

How does clutch dust get into the fluid ?
Think of it this way. Let's say you have a pet door on the deck. It's for the cat. The cat passes comfortably thru that door.

You have a collie too. But it can't get through that door.

Not trying to over-simplify, just make the core issue understandable.

A seal on a moving part such as the main shaft in the actuator can have the effect of squeegeeing in small particles of clutch dust, while not permitting passage outward of the larger and more complex molecules of the clutch fluid.

Once in the fluid the particles migrate with the normal flow. They tend to precipitate out when not agitated. It seems clear the dust particles are causing nicks, abrasions, wear points on the seals, leading to failure over time.

Ranger

Last edited by Ranger; 02-14-2009 at 01:26 PM.
Old 02-14-2009, 01:37 PM
  #35  
need-for-speed
Team Owner
 
need-for-speed's Avatar
 
Member Since: Feb 2000
Location: Conroe Texas
Posts: 35,254
Received 865 Likes on 608 Posts
CI 1-4-5-8-9-10 Vet
St. Jude Donor '03,'04,'05,'07,08,'09,'10,’17

Default

Originally Posted by Tzzird
You must be in the population of vette owners that run theirs at the limit more often than they should.

Mine was just as bad just as early.
:

While I don't abuse my baby, I do believe in "letting the horses run free (and often)"

Originally Posted by Ranger
Think of it this way. Let's say you have a pet door on the deck. It's for the cat. The cat passes comfortably thru that door.

You have a collie too. But it can't get through that door.

Not trying to over-simplify, just make the core issue understandable.

A seal on a moving part such as the main shaft in the actuator can have the effect of squeegeeing in small particles of clutch dust, while not permitting passage outward of the larger and more complex molecules of the clutch fluid.

Once in the fluid the particles migrate with the normal flow. They tend to precipitate out when not agitated. It seems clear the dust particles are causing nicks, abrasions, wear points on the seals, leading to failure over time.

Ranger
Thanks Ranger. That does make sense. Dust gets on the shaft and the seals wipe the shaft.
Old 02-14-2009, 01:48 PM
  #36  
Red Cell
Melting Slicks
 
Red Cell's Avatar
 
Member Since: Apr 2007
Location: Vancouver
Posts: 2,493
Likes: 0
Received 0 Likes on 0 Posts
Default

Thank-you RANGER.

It's always nice obtaining information like this and appreciate the amount of work that went into your instructional video.

Nice to see you back and hope all is well.

Red Cell.
Old 02-14-2009, 02:12 PM
  #37  
johnodrake
Moderator

Support Corvetteforum!
 
johnodrake's Avatar
 
Member Since: Dec 2002
Location: Lakewood Ranch, FL
Posts: 40,069
Received 3,579 Likes on 1,619 Posts

Default

Most excellent, Ranger! Thanks for sharing! Don't be a stranger, Ranger!

Get notified of new replies

To Take Care of Your Clutch--Preventing or Curing Pedal Issues

Old 02-14-2009, 02:17 PM
  #38  
fred_S
Pro
 
fred_S's Avatar
 
Member Since: Jul 2008
Location: Netherlands
Posts: 730
Received 3 Likes on 2 Posts

Default

I have mastered the "Ranger" art of clutch fluid maintenance, now it's time to master his gear change technique.
Excellent article, very well made video, I have downloaded the HD version from Youtube.

THANKS !!
Old 02-14-2009, 03:05 PM
  #39  
Rich Farr
Racer
 
Rich Farr's Avatar
 
Member Since: Apr 2006
Location: KITCHENER ONTARIO
Posts: 443
Received 12 Likes on 10 Posts

Default Great video

Dear Ranger,

I used your method two years ago and it worked great. I commented at the time, that based on the volume of the resovoir it would take three cans of new fluid to get the majority of old fluid replaced with new fluid by gradual mixing. You commented that this was about right. I used all three cans over a couple of weeks and the fluid has stayed clear for two years.

Thanks,

Rich
Old 02-15-2009, 02:54 PM
  #40  
BAMF AE
Safety Car
 
BAMF AE's Avatar
 
Member Since: Mar 2005
Location: The Surgeon General has warned that it's ok to smoke mustangs!
Posts: 4,454
Likes: 0
Received 1 Like on 1 Post
St. Jude Donor '06-'07

Default

Thank you Roger for this very informative post w/video!

07' MN6 coupe with 23K on the ticker. Last week, while having my oil changed, I had my cluth fluid checked. It was completely black! They poured in new fluid. Just today, I checked on it again, and it's already solid black. I do NOT shift or drive aggresively!

Questions:

1.) Does this mean that it's too late for me? In other words, do I already have a case of "Clutch Fluid" syndrome, which will require the car to be sent to the shop?

2.) If so, is this something covered by Warranty

Now that I've watched your vid, I will make sure to stay on top of this much more frequently.


Quick Reply: Take Care of Your Clutch--Preventing or Curing Pedal Issues



All times are GMT -4. The time now is 01:16 PM.