[ZR1] stealthfrc's ZR1 build thread
#1
Melting Slicks
Thread Starter
stealthfrc's ZR1 build thread
figured i start one of these.
i purchased a 2011 zr1 out of California about 2 months ago.
i started collecting parts right away.
also found out the car was part of the melted brick club. luckily no engine damage but the coating on the rotors needs to be redone. plan is to enjoy the car till winter then send the blower out for porting and repairs along with a few other mods. time will tell.
mod list:
synergy intake
ID1300's
flex fuel sensor
grip tech 2.45 pulley
TPIS 102MM throttle body
kong ported LPE snout
modded stock intercooler bricks
edelbrock HX that was modded for -20 in and outlets
billet blower coolant adaptors that were modded for dual -12 fittings
custom y fittings for 2-12 to 1 -20 fitting.
custom built ice tank,
a lot of time and thought went into the ice tank. my buddy wanted to try some things out and i also didn't want the thing mounted to the floor, i wanted this install clean and very easily reversible. he came up with a custom mount for it and its rock solid. the whole setup flows some serious water and looks pretty cool with all the fab work he did. has some serious talent.
he also modded a set of stock Downpipes, i didn't feel the need to buy headers at this point with the build and i needed an exhaust that would pass "emissions" up this way so he gutted the cats and welded 3" tube so its a nice smooth flowing exhaust, you would never know they were even modded.
wheels are 19/20 forgestar cf5v, i love these wheels, i had them on my mustang. by far my favorite wheel made by them
i also have a set of 18" f14's for the rear coming for a drag radial.
mods to be installed once i get the car back
DD mods full audio upgrade.
front and rear speakers
sub
headunit
carbon mirrors
lightwurkz carbon fiber head light bezels
i purchased a 2011 zr1 out of California about 2 months ago.
i started collecting parts right away.
also found out the car was part of the melted brick club. luckily no engine damage but the coating on the rotors needs to be redone. plan is to enjoy the car till winter then send the blower out for porting and repairs along with a few other mods. time will tell.
mod list:
synergy intake
ID1300's
flex fuel sensor
grip tech 2.45 pulley
TPIS 102MM throttle body
kong ported LPE snout
modded stock intercooler bricks
edelbrock HX that was modded for -20 in and outlets
billet blower coolant adaptors that were modded for dual -12 fittings
custom y fittings for 2-12 to 1 -20 fitting.
custom built ice tank,
a lot of time and thought went into the ice tank. my buddy wanted to try some things out and i also didn't want the thing mounted to the floor, i wanted this install clean and very easily reversible. he came up with a custom mount for it and its rock solid. the whole setup flows some serious water and looks pretty cool with all the fab work he did. has some serious talent.
he also modded a set of stock Downpipes, i didn't feel the need to buy headers at this point with the build and i needed an exhaust that would pass "emissions" up this way so he gutted the cats and welded 3" tube so its a nice smooth flowing exhaust, you would never know they were even modded.
wheels are 19/20 forgestar cf5v, i love these wheels, i had them on my mustang. by far my favorite wheel made by them
i also have a set of 18" f14's for the rear coming for a drag radial.
mods to be installed once i get the car back
DD mods full audio upgrade.
front and rear speakers
sub
headunit
carbon mirrors
lightwurkz carbon fiber head light bezels
Last edited by StealthFRC; 08-27-2017 at 11:22 AM.
The following users liked this post:
IMXCITD (09-28-2017)
#2
Racer
figured i start one of these.
i purchased a 2011 zr1 out of California about 2 months ago.
i started collecting parts right away.
also found out the car was part of the melted brick club. luckily no engine damage but the coating on the rotors needs to be redone. plan is to enjoy the car till winter then send the blower out for porting and repairs along with a few other mods. time will tell.
mod list:
synergy intake
ID1300's
flex fuel sensor
grip tech 2.45 pulley
TPIS 102MM throttle body
kong ported LPE snout
modded stock intercooler bricks
edelbrock HX that was modded for -20 in and outlets
billet blower coolant adaptors that were modded for dual -12 fittings
custom y fittings for 2-12 to 1 -20 fitting.
custom built ice tank,
a lot of time and thought went into the ice tank. my buddy wanted to try some things out and i also didn't want the thing mounted to the floor, i wanted this install clean and very easily reversible. he came up with a custom mount for it and its rock solid. the whole setup flows some serious water and looks pretty cool with all the fab work he did. has some serious talent.
he also modded a set of stock Downpipes, i didn't feel the need to buy headers at this point with the build and i needed an exhaust that would pass "emissions" up this way so he gutted the cats and welded 3" tube so its a nice smooth flowing exhaust, you would never know they were even modded.
wheels are 19/20 forgestar cf5v, i love these wheels, i had them on my mustang. by far my favorite wheel made by them
i also have a set of 18" f14's for the rear coming for a drag radial.
mods to be installed once i get the car back
DD mods full audio upgrade.
front and rear speakers
sub
headunit
carbon mirrors
lightwurkz carbon fiber head light bezels
https://youtu.be/6IDvObipOZo
i purchased a 2011 zr1 out of California about 2 months ago.
i started collecting parts right away.
also found out the car was part of the melted brick club. luckily no engine damage but the coating on the rotors needs to be redone. plan is to enjoy the car till winter then send the blower out for porting and repairs along with a few other mods. time will tell.
mod list:
synergy intake
ID1300's
flex fuel sensor
grip tech 2.45 pulley
TPIS 102MM throttle body
kong ported LPE snout
modded stock intercooler bricks
edelbrock HX that was modded for -20 in and outlets
billet blower coolant adaptors that were modded for dual -12 fittings
custom y fittings for 2-12 to 1 -20 fitting.
custom built ice tank,
a lot of time and thought went into the ice tank. my buddy wanted to try some things out and i also didn't want the thing mounted to the floor, i wanted this install clean and very easily reversible. he came up with a custom mount for it and its rock solid. the whole setup flows some serious water and looks pretty cool with all the fab work he did. has some serious talent.
he also modded a set of stock Downpipes, i didn't feel the need to buy headers at this point with the build and i needed an exhaust that would pass "emissions" up this way so he gutted the cats and welded 3" tube so its a nice smooth flowing exhaust, you would never know they were even modded.
wheels are 19/20 forgestar cf5v, i love these wheels, i had them on my mustang. by far my favorite wheel made by them
i also have a set of 18" f14's for the rear coming for a drag radial.
mods to be installed once i get the car back
DD mods full audio upgrade.
front and rear speakers
sub
headunit
carbon mirrors
lightwurkz carbon fiber head light bezels
https://youtu.be/6IDvObipOZo
Btw I saw Ct. plates on the car what town are you in?, I am in Norwalk.
-Jim
#3
Melting Slicks
Thread Starter
#4
Intermediate
That's going to be one bad ride my man. I'm in the hunt for my very own Z. I am pretty set on a white on black set up like yours.
Since I'm a newb I'm going to ask a stupid question. What's the melted brick club?
Since I'm a newb I'm going to ask a stupid question. What's the melted brick club?
#5
Melting Slicks
Thread Starter
this is what the melted brick is. its the intercooler brick on the zr1, they melt due to high intake temps and continuously being run hard without the proper upgrades. luckily there wasn't much damage. i purchased the car this way, it wasn't disclosed to me. i purchased from a dealer out in cali, i have a few disputes with them over a few undisclosed issues with the car. I'm not letting it stop me from enjoying it tho.
Last edited by StealthFRC; 08-27-2017 at 03:02 PM.
#7
Melting Slicks
Thread Starter
#9
Melting Slicks
Thread Starter
#11
Melting Slicks
Thread Starter
the raptor is an amazing truck. one of my absolute favorite vehicle's I've owned. i have yet to come across anything i don't like about it.
i did not have a gen 1, when they came out i was doing way to much driving to justify having one, with the gen 2 the fuel economy is much better and i don't drive nearly as much now.
few more updates. the ice tank is finally done. exactly what i wanted, like i stated, i wanted something that would not need to be bolted to the floor. mounts are rock solid and the whole setup could easily be fit into any other car.
i also did a test fit and mounted up the new shoes, i can't wait to get this thing back on the ground.
Last edited by StealthFRC; 08-28-2017 at 07:30 PM.
The following users liked this post:
IMXCITD (09-28-2017)
#14
Go Fast
thanks, i love white/black. its not very common and looks great in person.
this is what the melted brick is. its the intercooler brick on the zr1, they melt due to high intake temps and continuously being run hard without the proper upgrades. luckily there wasn't much damage. i purchased the car this way, it wasn't disclosed to me. i purchased from a dealer out in cali, i have a few disputes with them over a few undisclosed issues with the car. I'm not letting it stop me from enjoying it tho.
this is what the melted brick is. its the intercooler brick on the zr1, they melt due to high intake temps and continuously being run hard without the proper upgrades. luckily there wasn't much damage. i purchased the car this way, it wasn't disclosed to me. i purchased from a dealer out in cali, i have a few disputes with them over a few undisclosed issues with the car. I'm not letting it stop me from enjoying it tho.
#15
Melting Slicks
Thread Starter
it showed no signs until I got a dashlogic and started watching my intake temps.
just cruising they were 130's and after just a 1 gear pull they would go up to 180.
#17
Team Owner
^ Now that's cool...never seen that before.
#18
Melting Slicks
Thread Starter
#19
Melting Slicks
Thread Starter
some more pics. got the headlights installed on the car today. still need to reinstall the body parts but my buddy wants to finish the engine bay first.
some more fab skill pics of the work my friend has done.
hand made/fabbed "y blocks" single -20 to dual -12
HX pics
he even made the hose clamps since he didn't have any for -20 line.
some more fab skill pics of the work my friend has done.
hand made/fabbed "y blocks" single -20 to dual -12
HX pics
he even made the hose clamps since he didn't have any for -20 line.
Last edited by StealthFRC; 08-30-2017 at 07:47 PM.