[Z06] MMS 265 build. 640rwhp/542rwtq N/A pump gas 91 octane.
#1
Racer
Thread Starter
MMS 265 build. 640rwhp/542rwtq N/A pump gas 91 octane.
Just wrapped up a build for a friend/customer using Tony Mamo aka Mamo Motorsports complete top end kit. Build is as follows-
MMS 265cc ported heads
MMS Stage 3.5 comp cam
Manton custom length pushrods
Johnson short travel lifters
MMS spec Yella Terra roller rockers
Ati under drive balancer
Msd intake manifold ported by MMS
Nick Williams 102mm tb
American racing 2" headers w/catted x pipe.
Corsa carbon fiber cai
52lb injectors
Rps carbon twin disc clutch also modified by Mamo motorsports.
This car (as far as I know) has the highest hp naturally aspirated of any c6 z06 in Utah with a factory bottom end. 640rwhp/542tq. These dyno pulls were on 91 octane pump gas, with no additives and no meth. I'm extremely happy with how this car turned out. A big thanks goes out to Tony from Mamo Motorsports for all the pieces, and all the tech advice. He was right there throughout the process answering questions and following up on progress from beginning to end. He's a top notch person to work with and his products work.
Modified slave
MMS 265cc ported heads
MMS Stage 3.5 comp cam
Manton custom length pushrods
Johnson short travel lifters
MMS spec Yella Terra roller rockers
Ati under drive balancer
Msd intake manifold ported by MMS
Nick Williams 102mm tb
American racing 2" headers w/catted x pipe.
Corsa carbon fiber cai
52lb injectors
Rps carbon twin disc clutch also modified by Mamo motorsports.
This car (as far as I know) has the highest hp naturally aspirated of any c6 z06 in Utah with a factory bottom end. 640rwhp/542tq. These dyno pulls were on 91 octane pump gas, with no additives and no meth. I'm extremely happy with how this car turned out. A big thanks goes out to Tony from Mamo Motorsports for all the pieces, and all the tech advice. He was right there throughout the process answering questions and following up on progress from beginning to end. He's a top notch person to work with and his products work.
Modified slave
Last edited by ALTRDTA; 11-05-2017 at 05:09 PM.
The following users liked this post:
ALTRDTA (11-05-2017)
The following users liked this post:
HC Mechanic (12-18-2017)
#4
Team Owner
Dayum....not a fan of that CAI, but damn fine results from that combo!
The following 2 users liked this post by MTPZ06:
ALTRDTA (11-05-2017),
HC Mechanic (12-18-2017)
The following users liked this post:
ALTRDTA (11-05-2017)
#6
Melting Slicks
Nice run, good results. Looks like AF ratio is about 12 to 1 in the upper RPMs. Hard to tell from chart.
Last edited by double06; 11-05-2017 at 07:36 AM. Reason: Adding stuff
The following users liked this post:
ALTRDTA (11-05-2017)
The following users liked this post:
ALTRDTA (11-05-2017)
#8
Team Owner
Great work as always Dan and Heath.
The following users liked this post:
ALTRDTA (11-05-2017)
#11
Racer
Thread Starter
#14
Le Mans Master
You can’t go wrong with Mamo Motorsports.
The following users liked this post:
ALTRDTA (11-05-2017)
The following users liked this post:
ALTRDTA (11-05-2017)
The following users liked this post:
ALTRDTA (11-05-2017)
#17
Drifting
Awesome results! About time that Bane427 car got the love it deserves!
The following users liked this post:
ALTRDTA (11-05-2017)
#18
Race Director
Very nice, especially on 91
The following users liked this post:
ALTRDTA (11-05-2017)
#19
1.18 CF damn. Uncorrected must have been around 545whp which explains why 91 had no issue given the altitude it must have been at to end up with SAE 1.18. Stock injectors too.
Last edited by lt1z; 11-05-2017 at 04:05 PM.