WTB: WTB **ZO6 Modified Mid $30's to Low $40's**
#21
Team Owner
Member Since: Jun 2000
Posts: 52,277
Likes: 0
Received 3 Likes
on
3 Posts
CI 3-4-5-6-10 Veteran
St. Jude Donor '03-'06-'08-'09-'10
This one just popped up, seems pretty close to what you're looking for.
https://www.corvetteforum.com/forums...heads-cam.html
https://www.corvetteforum.com/forums...heads-cam.html
#22
. Will get pictures of interested (new phone)
2010 Arctic White Grandsport Corvette 3LT
6 Speed Manual Transmisson
Mileage: roughly 20k, I'll need to check if interested.
Exterior body mods: Zr1 Carbon fiber splitter, Zr1 Carbon Fiber side skirts, Zr1 Carbon Fiber Spoiler. The halo is painted black and roof is the black glass roof.
Mods:
686HP/763TQ Tuned by HorsePowerAddicts
APS Twin Turbo Kit currently set at I believe 14psi
Hotwire Fuel pump kit to a JMS boost a pump
Alky-Control Meth
Bosch 85lb injectors
Lingenfelter 100mm Mass Air
Custom 3inch downpipe
Akrapovik 3inch X pipe and Bi-Mode Exhaust
MGW shifter with lower box
eBoost2 boost gauge/boost controller
AEM Wideband and AEM Fuel Pressor Gauge
Turbosmart 40 MM Dual Port BOV's (2)
Manifolds are wrapped aswell as starter
I'm sure I am forgetting something. I also have most of the stock parts. Car drives great, is a blast to drive and I have had zero issues. I've made about 6 passes at track. Ran a 10.4 with a 1.48 60 ft. With a better 60ft the car will run 9.90's and still carve up corners.
The bad: headlamps started peeling. No idea why, since the car is garage kept. That I'll have fixed. I already have a quote to have them repaired. There is a very small hole in drivers seat side bolster from a wiring screwdriver. (Very very small screwdriver) Barely noticeable. And the fronts splitter has the normal chips from MD streets.
I am from Maryland.
Also if interested. I have an upgraded set of DKT/APS stainless coated manifolds and downpipes. These allow you to run turbos up to a 67/66 and external gates. Negotiable a
2010 Arctic White Grandsport Corvette 3LT
6 Speed Manual Transmisson
Mileage: roughly 20k, I'll need to check if interested.
Exterior body mods: Zr1 Carbon fiber splitter, Zr1 Carbon Fiber side skirts, Zr1 Carbon Fiber Spoiler. The halo is painted black and roof is the black glass roof.
Mods:
686HP/763TQ Tuned by HorsePowerAddicts
APS Twin Turbo Kit currently set at I believe 14psi
Hotwire Fuel pump kit to a JMS boost a pump
Alky-Control Meth
Bosch 85lb injectors
Lingenfelter 100mm Mass Air
Custom 3inch downpipe
Akrapovik 3inch X pipe and Bi-Mode Exhaust
MGW shifter with lower box
eBoost2 boost gauge/boost controller
AEM Wideband and AEM Fuel Pressor Gauge
Turbosmart 40 MM Dual Port BOV's (2)
Manifolds are wrapped aswell as starter
I'm sure I am forgetting something. I also have most of the stock parts. Car drives great, is a blast to drive and I have had zero issues. I've made about 6 passes at track. Ran a 10.4 with a 1.48 60 ft. With a better 60ft the car will run 9.90's and still carve up corners.
The bad: headlamps started peeling. No idea why, since the car is garage kept. That I'll have fixed. I already have a quote to have them repaired. There is a very small hole in drivers seat side bolster from a wiring screwdriver. (Very very small screwdriver) Barely noticeable. And the fronts splitter has the normal chips from MD streets.
I am from Maryland.
Also if interested. I have an upgraded set of DKT/APS stainless coated manifolds and downpipes. These allow you to run turbos up to a 67/66 and external gates. Negotiable a
#24
Intermediate
Member Since: Jan 2011
Location: Fort Myers FL
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
Not sure how all this works but I have a pristine Jetstream Blue 08 ZO6 with a new 2013 GM LS7 engine with only 8,300 mi. The car has 25,300 mi. and has a lot of extras. It is listed on the Forum. Car has a cam, long tube headers, FAST intake and much more. It was dyno tuned at 542 RWHP. Asking $39,500. Terry
#28
#29
Instructor
Fully built zo6 450ci Rhs block, mast heads, rpm l7 tr6060, ect 30k+ plus in parts alone
https://www.corvetteforum.com/forums...l7-tr6060.html
https://www.corvetteforum.com/forums...l7-tr6060.html
Last edited by Daniel Hoffele; 09-19-2017 at 03:27 PM.