OFFICIAL A&A SUPERCHARGERS Q&A thread - Page 49 - CorvetteForum - Chevrolet Corvette Forum Discussion

Notices
C6 Forced Induction/Nitrous C6 Corvette Turbochargers, Superchargers, Pulley Upgrades, Intercoolers, Wet and Dry Nitrous Injection, Meth
Sponsored by:
Sponsored by:

OFFICIAL A&A SUPERCHARGERS Q&A thread

Old 07-04-2018, 03:58 PM
  #961  
Cooter272
CF Member
 
Member Since: Aug 2014
Location: Bay Area. NorCal CA
Posts: 68
Thanks: 0
Thanked 1 Time in 1 Post
Default

Originally Posted by [email protected] View Post
Grind the dark area of your red shade. Should be fine just need a tiny air gap and it's good.
Thanks for the quick reply, Josh. It's ground down now and should have enough clearance.

I didn't see mention in the instructions but from another guy's install thread I see I'll need to cut a hole on the passenger side for the hose from the intercooler to pass thru. Any idea what size hole saw I need to buy?

Other than that, I got the steering rack out of the way today, replaced the OEM harmonic balancer with a Powerbond, and cut down the top of the radiator for clearance. The Chrysler puller from Autozone is great. Bought a balancer install tool on Amazon for about $12. New balancer is pressed on but I havent put the ARP bolt on yet because I still need to pin it. I thinks that's as far as I can go now until the kit arrives from A&A....weeeee!

Last edited by Cooter272; 07-04-2018 at 04:02 PM.
Cooter272 is offline  
Old 07-17-2018, 11:22 AM
  #962  
Cooter272
CF Member
 
Member Since: Aug 2014
Location: Bay Area. NorCal CA
Posts: 68
Thanks: 0
Thanked 1 Time in 1 Post
Default

Hey Josh, couple quick questions while I wrap up my install.

I didnt see mention in the instructions but have read others talking about needing to change the stock fuel pump's fuse from 20A to 30A. Should this be done?
Are you guys putting the CARB exempt decal right next to the original emissions decal on the passenger side of the hood?
Can I get you to email me a base tune for my 2005 base model with auto trans? I have the 4" pulley and 60lb injectors.

Thanks!
Cooter272 is offline  
Old 07-19-2018, 12:28 PM
  #963  
[email protected]
Platinum Supporting Vendor
 
Josh@AandASuperchargers's Avatar
 
Member Since: Jul 2011
Posts: 1,772
Thanked 94 Times in 80 Posts
Default

Originally Posted by Cooter272 View Post
Hey Josh, couple quick questions while I wrap up my install.

I didnt see mention in the instructions but have read others talking about needing to change the stock fuel pump's fuse from 20A to 30A. Should this be done?
Are you guys putting the CARB exempt decal right next to the original emissions decal on the passenger side of the hood?
Can I get you to email me a base tune for my 2005 base model with auto trans? I have the 4" pulley and 60lb injectors.

Thanks!
Yes put the extra 30A underhood in place of stock fuse.
We typically put the sticker on the top shroud near the driver side.
Send me an email about the base tune. [email protected]
Josh@AandASuperchargers is offline  
Old 07-20-2018, 10:39 AM
  #964  
Cooter272
CF Member
 
Member Since: Aug 2014
Location: Bay Area. NorCal CA
Posts: 68
Thanks: 0
Thanked 1 Time in 1 Post
Default

I REALLY appreciate the help, Josh! I think just one more question though. Is the Racetronix harness necessary to ad? I understand it takes the load off fuel pump relay circuit. Since it's not part of the kit though, I assume you guys arent putting them on your installs, right?
Cooter272 is offline  
Old 07-20-2018, 11:48 AM
  #965  
[email protected]
Platinum Supporting Vendor
 
Josh@AandASuperchargers's Avatar
 
Member Since: Jul 2011
Posts: 1,772
Thanked 94 Times in 80 Posts
Default

Originally Posted by Cooter272 View Post
I REALLY appreciate the help, Josh! I think just one more question though. Is the Racetronix harness necessary to ad? I understand it takes the load off fuel pump relay circuit. Since it's not part of the kit though, I assume you guys arent putting them on your installs, right?
It's optional, and not required.
Josh@AandASuperchargers is offline  
Old 07-29-2018, 07:19 PM
  #966  
JetstreamGS
CF Senior Member
 
JetstreamGS's Avatar
 
Member Since: Jul 2014
Posts: 952
Thanked 24 Times in 24 Posts
Default

Josh any updates with the release of the heritage series blowers?
JetstreamGS is offline  
Old 09-20-2018, 02:07 PM
  #967  
[email protected]
Platinum Supporting Vendor
 
Josh@AandASuperchargers's Avatar
 
Member Since: Jul 2011
Posts: 1,772
Thanked 94 Times in 80 Posts
Default

Originally Posted by JetstreamGS View Post
Josh any updates with the release of the heritage series blowers?
Still waiting on pricing from Vortech so I can sell some. -Josh

Anyone interested send me email to get on my list. Josh @ aacorvette.com
Josh@AandASuperchargers is offline  
Old 09-20-2018, 03:38 PM
  #968  
JetstreamGS
CF Senior Member
 
JetstreamGS's Avatar
 
Member Since: Jul 2014
Posts: 952
Thanked 24 Times in 24 Posts
Default

Originally Posted by [email protected] View Post
Still waiting on pricing from Vortech so I can sell some. -Josh

Anyone interested send me email to get on my list. Josh @ aacorvette.com
Thanks again Josh, that was me you were speaking to. Discount for getting the ball rolling?
JetstreamGS is offline  


Thread Tools
Search this Thread
Quick Reply: OFFICIAL A&A SUPERCHARGERS Q&A thread


Sponsored Ads
Vendor Directory

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

© 2018 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
 
  • Ask a Question
    Get answers from community experts
Question Title:
Description:
Your question will be posted in: