Texas Speed C6 Long Tube Headers & X Pipe Results & Pricing!!
#161
Melting Slicks
My 08 C6 automatic with NPP dynoed 427.5 rwhp & 423.5 tq with an Airaid, Z06 manifolds, tune and underdrive pulley on a Mustang dyno. Was yours tuned?
#162
Drifting
I will first say that I would do it again in a second based on value.
They are not perfect headers. I had a min hole in one of my primary pipes that needed to be welded up and the fit isn't perfectly semetrical down the center of the car. In the end it cost me an extra $150 to get them on the car over what it would have cost to install a brand that had better "quality control". The finish is great, under the hood looks great, I could FEEL a difference in performance.
They are not perfect headers. I had a min hole in one of my primary pipes that needed to be welded up and the fit isn't perfectly semetrical down the center of the car. In the end it cost me an extra $150 to get them on the car over what it would have cost to install a brand that had better "quality control". The finish is great, under the hood looks great, I could FEEL a difference in performance.
They seem like a great combo of 1 7/8" primaries AND LONG primaries, this theoretically should be the best of both worlds
#163
My 08 C6 automatic with NPP dynoed 427.5 rwhp & 423.5 tq with an Airaid, Z06 manifolds, tune and underdrive pulley on a Mustang dyno. Was yours tuned?
yes, this numbers is after the tune
before the tune was 409 rwhp & 416 tq
#164
I also have an 08 c6 automatic with just intake/tune and it made 406rwhp and 390rwtq, i'm hoping to get to 435rwhp with headers.
#165
Those numbers are definitely low, do you have a good tuner? Do you know if your car was pulling timing? What gas were you running? If using HP tuners make sure the car wasn't pulling any timing up top. All dyno's are different, so if we knew your baseline, that would help. An MN6 LS3 car with intake/headers tune should get to near 440rwhp though.
#166
Melting Slicks
That's pretty good for stock manifolds. If I go from 427 to 435 with my headers I've spent a lot for so little.
#167
Melting Slicks
You should go up a little more than 8 but what is more important is that the overall power curve should be better. The Z manifolds seem to be a matter of constant debate since some see good power gains for a simple manifold swap whereas others see little to no gain at all. LT's are a great decision though, make even better gains when moving on to a cam or head swap.
#172
Will work for HPDE time.
#173
Le Mans Master
Jon, Matt.... When are you guys going to have these ready to go? I had your Texas Speed headers on my C5Z that I sold 2 days ago. We had some fitment issues with the xpipe, and your customer service was great(corvettes of houston, Sept 09, brownsgym@gmail.com)
I have an A&A kit ready when I buy my C6 in the next couple weeks, and need headers to go on the car when I buy it. Will you guys have a set by then? I have to go with headers when I buy the car so that the fiancee doesn't notice when the car comes home for the first time. Shoot me a PM or email me, please.
I have an A&A kit ready when I buy my C6 in the next couple weeks, and need headers to go on the car when I buy it. Will you guys have a set by then? I have to go with headers when I buy the car so that the fiancee doesn't notice when the car comes home for the first time. Shoot me a PM or email me, please.
#174
Premium Supporting Vendor
Jon, Matt.... When are you guys going to have these ready to go? I had your Texas Speed headers on my C5Z that I sold 2 days ago. We had some fitment issues with the xpipe, and your customer service was great(corvettes of houston, Sept 09, brownsgym@gmail.com)
I have an A&A kit ready when I buy my C6 in the next couple weeks, and need headers to go on the car when I buy it. Will you guys have a set by then? I have to go with headers when I buy the car so that the fiancee doesn't notice when the car comes home for the first time. Shoot me a PM or email me, please.
I have an A&A kit ready when I buy my C6 in the next couple weeks, and need headers to go on the car when I buy it. Will you guys have a set by then? I have to go with headers when I buy the car so that the fiancee doesn't notice when the car comes home for the first time. Shoot me a PM or email me, please.
__________________
COMP - FAST - PACESETTER - CALLIES - COMETIC GASKETS - MONSTER CLUTCHES - MOSER ENGINEERING - KOOKS
ARP - GM BOLTS AND GASKETS - MSD - NGK - POWERBOND - WISECO - ASP - AND MORE!
Largest Stocking Distributor of LS-x Engines / Largest LS-x Comp Cams Distributor in the Country!
COMP - FAST - PACESETTER - CALLIES - COMETIC GASKETS - MONSTER CLUTCHES - MOSER ENGINEERING - KOOKS
ARP - GM BOLTS AND GASKETS - MSD - NGK - POWERBOND - WISECO - ASP - AND MORE!
#176
Is the stainless switch going to mean $$$? I was gonna buy your LT's this winter because of the price and reputation of your shop/customer service. I really don't wanna spend all of my mod money on LT's when the rest could be used elsewhere. Will you still provide a coated, non-stainless version?
#177
Drifting
Is the stainless switch going to mean $$$? I was gonna buy your LT's this winter because of the price and reputation of your shop/customer service. I really don't wanna spend all of my mod money on LT's when the rest could be used elsewhere. Will you still provide a coated, non-stainless version?
#178
Intermediate
Member Since: Feb 2008
Location: Lakeland Florida
Posts: 35
Likes: 0
Received 0 Likes
on
0 Posts
I have had your headers on order through a local shop for 2 1/2 to 3 months now. I do not understand why you would discontinue the set you had before a replacement was ready. It would nice to know something instead of canceling my order and ordering headers and my other items from somewhere else.
#180
Former Vendor
Member Since: Jun 2006
Location: Lubbock Texas
Posts: 300
Likes: 0
Received 0 Likes
on
0 Posts
It just kind of worked out like this. It was either keep them the way they were and order another stocking order or try and make the switch now and improve the product for our customers. I apologize that it is taking so long to get them back in but that is the hand we have been dealt. Obviously we are trying to get them back in as quickly as possible. Anyone, including the shop you ordered through, were notified up front about the change and the delay we were looking at. The shop has been refunded as we don't want any pending orders for these since they are not in stock.
However, when they are available, I think everyone will be very impressed by the quality and fit as well as the price!
Jon
However, when they are available, I think everyone will be very impressed by the quality and fit as well as the price!
Jon