Rayzzz

Just finished working on my 2005 C6 A4 automatic. I installed a Vortec supercharger that made 574 HP at the end Nov. and this what I did next. Rear widebody, 12x19 and 9.5x18 Z06 chrome rims and Nitto Invo 345/30ZR 19's rear and 255/40ZZR 18's front. We still have snow on the ground and nasty on the streets. May have some rain next Tuesday. Man I need some clean streets. Heres some pics.

THANKS RAYZZZ MY CORVETTE LIKES MY MONEY

Rayzzz

Rayzzz

I also did these Pypes exhaust cutouts after supercharger.

ls3gotcha

looks fantastic, great job

TrenAman

looks great, hope you have a built tranny in that 05 with a blower and now rubber to put it down with.. Your going to need it!

davidtcpa

Rayzzz

Yes I know. Last summer I installed a built 3.90 rear diff and a Pro Torque 2800 stall. A blast to drive. Just got to not be Stupid and be Lucky. Tranny may be in the future.
THANKS RAYZZZ MY CORVETTE LIKES MY MONEY

TrenAman

ok, pm where I can get that skull please..

Rayzzz

B&M trans cooler I installed last summer. Largest one with fan 70297
Link below
http://www.summitracing.com/parts/BMM-70297/


THANKS RAYZZZ MY CORVETTE LIKES MY MONEY


I made this to go In front of drivers front wheel

Rayzzz

How I did shift ****


CLICK BELOW

http://forums.corvetteforum.com/c6-t...t-****-c6.html






THANKS RAYZZZ MY CORVETTE LIKES MY MONEY

m R g S r

looks good. paint looks like it matches, how is it in the sun? did the body shop blend it into the doors and the bumper, or did they just try and match it?

Rayzzz

Paint supply place blended the paint to match. The paint supply place used the gas door and when the paint shop painted the fenders they forgot to paint gas door and still looks good. Dupont paint.
THANKS RAYZZZ MY CORVETTE LIKES MY MONEY

Motorhead-47

Tell me about this panel...a do-it-yourself effort?

Keith N

Well done, it looks great! Are you running the stock Z06 front wheels & tires sizes?

Rayzzz

Stock C6 offset with Nitto Invo 255/40ZR18. Fronts are 9.5x18 and rears are OEM speedlines 19x12 with 345/30ZR19. I purchased the rims from Bob at House of Wheels a forum vendor. The rears are OEM speedlines 19x12 with 345/30ZR19. Nice guy.

THANKS RAYZZZ MY CORVETTE LIKES MY MONEY

HP JNKEY

Nice job. The car looks great and I like the house too.

BoosterClub

Aww you got me all excited. Just FYI nitto invos 345s are really about the same width as a normal 325s (~3.2 " width). I haven't had a chance to measure to see if a 345 will fit with the stocks wheels (13.8 width) and I thought this was confirming that .

Rayzzz

Motorhead-47 Here are a few pics of what I did. Razor knife, heat gun, 2 part adhesive and gutter guard stuff for back side. Piece next to razor knife is a part of a cheap mud flap to fill hole were brake duct was.. 30* cooler after install of trans cooler

THANKS RAYZZZ MY CORVETTE LIKES MY MONEY

Tally Ho

Car looks great.

Rayzzz

My Pypes Youtube video. If you want to see and here .
THANKS RAYZZZ MY CORVETTE LIKES MY MONEY
CLICK BELOW
http://www.youtube.com/watch?v=FEvvQ9biiFE