Mat Anchor Point Change
12-28-2012, 06:10 PM
#1
Premium Supporting Vendor
Thread Starter
Member Since: Oct 2004
Location: Manassas Park VA
Posts: 36,681
Received 421 Likes
on
322 Posts
St. Jude Donor '07-'08,-'13-'14, '16-'17
Mat Anchor Point Change
Anyone know the exact date that the Anchor Points for the Floor Mats
Changed in 2013.
It was sometime after May...
Tks
Chip
Changed in 2013.
It was sometime after May...
Tks
Chip
__________________
..................Click for
..................Click for
Last edited by CCA Corvette Parts; 12-28-2012 at 06:38 PM.
12-29-2012, 03:29 PM
#3
Consider this a bump 
. I'd say it's a manufacturing error; how in the world is GM going to change the floor mats in the last weeks of C6 production? Doesn't make any sense. Unless they changed the location in the past, and want to use up old inventory, perhaps? That's weird, regardless. Is there an official way to find that out for sure? Good luck.
. I'd say it's a manufacturing error; how in the world is GM going to change the floor mats in the last weeks of C6 production? Doesn't make any sense. Unless they changed the location in the past, and want to use up old inventory, perhaps? That's weird, regardless. Is there an official way to find that out for sure? Good luck.
12-29-2012, 10:12 PM
#5
Premium Supporting Vendor
Thread Starter
Member Since: Oct 2004
Location: Manassas Park VA
Posts: 36,681
Received 421 Likes
on
322 Posts
St. Jude Donor '07-'08,-'13-'14, '16-'17
Consider this a bump . I'd say it's a manufacturing error; how in the world is GM going to change the floor mats in the last weeks of C6 production? Doesn't make any sense. Unless they changed the location in the past, and want to use up old inventory, perhaps? That's weird, regardless. Is there an official way to find that out for sure? Good luck.
. I'd say it's a manufacturing error; how in the world is GM going to change the floor mats in the last weeks of C6 production? Doesn't make any sense. Unless they changed the location in the past, and want to use up old inventory, perhaps? That's weird, regardless. Is there an official way to find that out for sure? Good luck.out exactly when for Lloyds...
Peace
Chip
12-30-2012, 08:51 PM
#7
Racer
I ordered floor mats and rear deck mat from LLoyds around the 18th of December for my 2013 GS. When they arrived, they did not fit. The anchor holes were too close together. I went back to their site yesterday to re-enact my order to see if I screwed up and VOILA,there are now TWO options for the front mats, older models and newer models. Glad I saw this post, because I thought I was the dummy. 
01-02-2013, 11:32 AM
#8
Intermediate
Member Since: Oct 2012
Posts: 26
Likes: 0
Received 0 Likes
on
0 Posts
Just ordered some Lloyd mat's for my 2013 GS convert. and mine did not fit either. same problem, way off in location. My car was made in late November 2012, been in contact with supplier and they are working on getting me out another new set. Don't know why GM would revise the mounting when this car is going out of production in 2 Months.
01-04-2013, 07:37 PM
#9
Premium Supporting Vendor
Thread Starter
Member Since: Oct 2004
Location: Manassas Park VA
Posts: 36,681
Received 421 Likes
on
322 Posts
St. Jude Donor '07-'08,-'13-'14, '16-'17
Here is the Answer, direct from Chevy and Lloyds
With the help of General Motors and especially their Corvette division, we have resolved the fastener change issue
in the 2013 Corvette.
The breakpoint VIN number for the fastener change is 1G1YV2DW8D5101979, Corvettes with this VIN and higher will
use the 2013.5 Corvette pattern # 3154030. This Corvette rolled off the line 6/19/12.
Customers only need the last 6 digits of their VIN when ordering mats. Any 2013 Corvette with the last 6 digits of
101978 and lower should use the 2007.5 to 2013.5 pattern # 3154020 when ordering floor mats.
Peace
Chip
With the help of General Motors and especially their Corvette division, we have resolved the fastener change issue
in the 2013 Corvette.
The breakpoint VIN number for the fastener change is 1G1YV2DW8D5101979, Corvettes with this VIN and higher will
use the 2013.5 Corvette pattern # 3154030. This Corvette rolled off the line 6/19/12.
Customers only need the last 6 digits of their VIN when ordering mats. Any 2013 Corvette with the last 6 digits of
101978 and lower should use the 2007.5 to 2013.5 pattern # 3154020 when ordering floor mats.
Peace
Chip
01-07-2013, 12:58 PM
#10
Premium Supporting Vendor
Thread Starter
Member Since: Oct 2004
Location: Manassas Park VA
Posts: 36,681
Received 421 Likes
on
322 Posts
St. Jude Donor '07-'08,-'13-'14, '16-'17
UPDATE:
Picture is on the passenger side - Measure the Passenger side Hook
Vin #'s may not be correct - I spoke with a customer today that had
a lower VIN than what is listed above and had a 9.5" Hook
To be sure - Measure the Passenger Side Hook. It will be 8.25"
or 9.5"
Peace
Chip
Picture is on the passenger side - Measure the Passenger side Hook
Vin #'s may not be correct - I spoke with a customer today that had
a lower VIN than what is listed above and had a 9.5" Hook
To be sure - Measure the Passenger Side Hook. It will be 8.25"
or 9.5"
Peace
Chip
Last edited by CCA Corvette Parts; 01-08-2013 at 08:46 AM.
01-08-2013, 08:47 AM
#11
Premium Supporting Vendor
Thread Starter
Member Since: Oct 2004
Location: Manassas Park VA
Posts: 36,681
Received 421 Likes
on
322 Posts
St. Jude Donor '07-'08,-'13-'14, '16-'17
UPDATE 2:
Vin #'s should be good for Base and Convertible C6 Corvettes
Vin #'s will not work for Grand Sport - Z06 and ZR1
Peace
Chip
Vin #'s should be good for Base and Convertible C6 Corvettes
Vin #'s will not work for Grand Sport - Z06 and ZR1
Peace
Chip
