2005 ECM Replacement Where to buy?
#1
Safety Car
Thread Starter
2005 ECM Replacement Where to buy?
I have been having trouble with my 2005 C6 dying after 40-50 minutes of running, all evidence is starting to point at a bad ECM.
So if I have to get one, where is the best place to save money and maybe get a one with a good flash?
Here are the threads.
https://www.corvetteforum.com/forums...then-dies.html
https://www.corvetteforum.com/forums...n-running.html
https://www.corvetteforum.com/forums...-tech-2-a.html
So if I have to get one, where is the best place to save money and maybe get a one with a good flash?
Here are the threads.
https://www.corvetteforum.com/forums...then-dies.html
https://www.corvetteforum.com/forums...n-running.html
https://www.corvetteforum.com/forums...-tech-2-a.html
Last edited by TedG; 08-26-2017 at 02:46 PM.
#2
Did you pull codes, and the codes are stating the the ECM is the problem???
#3
Safety Car
Thread Starter
I went so far as to buy a Tech 2.
Sometimes it sets off a code other times not.
I have multiple snapshots, and nothing really points to anything in particular.
The one thing that is looking bad, is it died and I looked at the injector control and it stayed lit and wasn't flashing.
#4
Safety Car
Thread Starter
What is really strange is the lack of answers. There was a time when a problem like this would garner dozens of answers in no time.
I have not had time for forums for quite a while, but finally getting a huge job through compliance has given me some more time.Things have changed.
I have not had time for forums for quite a while, but finally getting a huge job through compliance has given me some more time.Things have changed.
#5
Team Owner
Here at Cultrag you can put your VIN in and get the exact parts for your Vette specifically - It is #5 In the diagram https://www.cultragfactoryparts.com/...YtMGwtdjgtZ2Fz
$313.04
It looks as if your ECM part number is: GM 19210071
$255.07
https://www.gmdiscountautoparts.com/...89Jnk9JnQ9JmU9
$250.43
https://www.gmpartsdirect.com/oem-parts/gm-ecm-19210071
$282.89
http://www.wholesalegmpartsonline.co.../19210071.html
Summit Racing $236.97 - Best price thus far!
https://www.summitracing.com/parts/ado-19210071
Just cross reference your VIN on CULTRAG and make sure you have the correct ECM and you should be good with the above links
Thanks,Matt
$313.04
It looks as if your ECM part number is: GM 19210071
$255.07
https://www.gmdiscountautoparts.com/...89Jnk9JnQ9JmU9
$250.43
https://www.gmpartsdirect.com/oem-parts/gm-ecm-19210071
$282.89
http://www.wholesalegmpartsonline.co.../19210071.html
Summit Racing $236.97 - Best price thus far!
https://www.summitracing.com/parts/ado-19210071
Just cross reference your VIN on CULTRAG and make sure you have the correct ECM and you should be good with the above links
Thanks,Matt
The following users liked this post:
TedG (08-27-2017)
The following users liked this post:
TedG (08-27-2017)
#7
Safety Car
Thread Starter
Here at Cultrag you can put your VIN in and get the exact parts for your Vette specifically - It is #5 In the diagram https://www.cultragfactoryparts.com/...YtMGwtdjgtZ2Fz
$313.04
It looks as if your ECM part number is: GM 19210071
$255.07
https://www.gmdiscountautoparts.com/...89Jnk9JnQ9JmU9
$250.43
https://www.gmpartsdirect.com/oem-parts/gm-ecm-19210071
$282.89
http://www.wholesalegmpartsonline.co.../19210071.html
Summit Racing $236.97 - Best price thus far!
https://www.summitracing.com/parts/ado-19210071
Just cross reference your VIN on CULTRAG and make sure you have the correct ECM and you should be good with the above links
Thanks,Matt
$313.04
It looks as if your ECM part number is: GM 19210071
$255.07
https://www.gmdiscountautoparts.com/...89Jnk9JnQ9JmU9
$250.43
https://www.gmpartsdirect.com/oem-parts/gm-ecm-19210071
$282.89
http://www.wholesalegmpartsonline.co.../19210071.html
Summit Racing $236.97 - Best price thus far!
https://www.summitracing.com/parts/ado-19210071
Just cross reference your VIN on CULTRAG and make sure you have the correct ECM and you should be good with the above links
Thanks,Matt
The good part is there is a Summit where I live and can go pick it up.
Now I have to learn about getting it flashed. And I have a Tech 2, but I have not been able to determine if I can do it with that..
#8
Team Owner
Personally I have not done this myself, but I have only seen it done and know it can be done.
I am sure there is someone who is going to be able to assist you through it or there is a Forum that will have some help in aiding you through the steps/process.
Please keep us posted - if I can be of any help I will -
Thanks,Matt
#9
Safety Car
Thread Starter
With a Tech 2 you should be able to code the/your VIN into the new ECM and load a stock tune from GM for the 2005 right into it.
Personally I have not done this myself, but I have only seen it done and know it can be done.
I am sure there is someone who is going to be able to assist you through it or there is a Forum that will have some help in aiding you through the steps/process.
Please keep us posted - if I can be of any help I will -
Thanks,Matt
Personally I have not done this myself, but I have only seen it done and know it can be done.
I am sure there is someone who is going to be able to assist you through it or there is a Forum that will have some help in aiding you through the steps/process.
Please keep us posted - if I can be of any help I will -
Thanks,Matt
I have done a bit of reading but it isn't quite clear what I really need to do.
Also whenever I find a solution to a problem I make sure that every thread that had something to do with it gets updated. I hate finding a thread that has your problem and dead ends without a solution.
#10
Team Owner
Thanks,
I have done a bit of reading but it isn't quite clear what I really need to do.
Also whenever I find a solution to a problem I make sure that every thread that had something to do with it gets updated. I hate finding a thread that has your problem and dead ends without a solution.
I have done a bit of reading but it isn't quite clear what I really need to do.
Also whenever I find a solution to a problem I make sure that every thread that had something to do with it gets updated. I hate finding a thread that has your problem and dead ends without a solution.
Perhaps they will have mercy and give you some help or guidance - It won't hurt to give them a ring or drop by and talk with them (dropping by, if close enough, usually is best)
Thanks,Matt
#12
Safety Car
Thread Starter
Do you have any idea how to get hold of him? I wouldn't mind getting an ECU that has a mild tune on it.
#13
Melting Slicks
I'll search for his number.
The following users liked this post:
TedG (08-27-2017)
#14
Former Vendor
Member Since: Nov 2005
Location: Ossining New York
Posts: 11,792
Received 243 Likes
on
183 Posts
St. Jude Donor '07-'08-'09-'10-'12-'13-'14
Please give me a ring!
I have plenty of 2005 ECMs and I can set you up with the Amazing CoW BOOSTER! and a great tune.
I'll even make you a better deal as I just launched my Labor Day sale.
Please call me monday at 914-332-0049
Thank you.
Chuck CoW
#15
Safety Car
Thread Starter
You will be hearing from me.
Thanks
#16
Safety Car
Thread Starter
So,
On to the next chapter in the dying C6.
I talked to Chuck (COW) and he convinced me to get an ECM from him with his tune in it.
What that means is that hopefully this will cure the problem. If not it takes the ECM out of the picture and leaves some still hidden problem.
But is does get me a tune that Chuck promises will make me smile. Okay I'm game.
As I explained to him I think cars are slow and dangerous. I'll take a bike with escape routes, ungodly acceleration, and brakes from hell.
I have been a member of this board for over 15 years and never once asked how to make this or any previous Vette go faster.
So something new for me.
Hopefully this nightmare is over.
To be continued.........
On to the next chapter in the dying C6.
I talked to Chuck (COW) and he convinced me to get an ECM from him with his tune in it.
What that means is that hopefully this will cure the problem. If not it takes the ECM out of the picture and leaves some still hidden problem.
But is does get me a tune that Chuck promises will make me smile. Okay I'm game.
As I explained to him I think cars are slow and dangerous. I'll take a bike with escape routes, ungodly acceleration, and brakes from hell.
I have been a member of this board for over 15 years and never once asked how to make this or any previous Vette go faster.
So something new for me.
Hopefully this nightmare is over.
To be continued.........
#17
Team Owner
So,
On to the next chapter in the dying C6.
I talked to Chuck (COW) and he convinced me to get an ECM from him with his tune in it.
What that means is that hopefully this will cure the problem. If not it takes the ECM out of the picture and leaves some still hidden problem.
But is does get me a tune that Chuck promises will make me smile. Okay I'm game.
As I explained to him I think cars are slow and dangerous. I'll take a bike with escape routes, ungodly acceleration, and brakes from hell.
I have been a member of this board for over 15 years and never once asked how to make this or any previous Vette go faster.
So something new for me.
Hopefully this nightmare is over.
To be continued.........
On to the next chapter in the dying C6.
I talked to Chuck (COW) and he convinced me to get an ECM from him with his tune in it.
What that means is that hopefully this will cure the problem. If not it takes the ECM out of the picture and leaves some still hidden problem.
But is does get me a tune that Chuck promises will make me smile. Okay I'm game.
As I explained to him I think cars are slow and dangerous. I'll take a bike with escape routes, ungodly acceleration, and brakes from hell.
I have been a member of this board for over 15 years and never once asked how to make this or any previous Vette go faster.
So something new for me.
Hopefully this nightmare is over.
To be continued.........
Just make sure that the tune isn't locked when you get it, just incase something goes wrong, talk to Mr. Cow, I'm sure he'll work with you, not sure if he locks his ECM's or not.
Thanks,Matt
#18
Former Vendor
Member Since: Nov 2005
Location: Ossining New York
Posts: 11,792
Received 243 Likes
on
183 Posts
St. Jude Donor '07-'08-'09-'10-'12-'13-'14
Nope.. Never is...
Well - glad to hear things are moving forward and that the ECM compatibility will be addressed -
Just make sure that the tune isn't locked when you get it, just incase something goes wrong, talk to Mr. Cow, I'm sure he'll work with you, not sure if he locks his ECM's or not.
Thanks,Matt
Just make sure that the tune isn't locked when you get it, just incase something goes wrong, talk to Mr. Cow, I'm sure he'll work with you, not sure if he locks his ECM's or not.
Thanks,Matt
I'm building the ecm as we speak!
Thanks again Ted.
Chuck CoW
The following users liked this post:
TedG (08-29-2017)
#19
Safety Car
Thread Starter
#20
Instructor