Premuim Quality Zr1 Carbon Fiber Front Splitter / Side Skirts **Vacuum Infused**
01-28-2016, 08:01 PM
#31
Former Vendor
Thread Starter
02-01-2016, 03:41 PM
#33
Drifting
Ever get blemish side skirts? I have a z06 race car in need of side skirts, but ultimately don't need show quality... Would even take a set with bad weave and paint them black... Regular or wide, as long a they have flaps included...
02-01-2016, 04:29 PM
#35
Former Vendor
Thread Starter
I haven't got a chance to take pictures of them yet. I can post them up in an hour or so. Lmk.
02-01-2016, 04:38 PM
#36
Drifting
I do have blemished skirts both in vacuum infused and hand laid. I can get the hand laid out to you for $500 shipped, passenger side is good and the flaps are good. I can get the vacuum infused out to you for also $500 shipped, but this one has quite a few bubbles along the edge on both skirts also the flaps have bubbles but its not much.
I haven't got a chance to take pictures of them yet. I can post them up in an hour or so. Lmk.
I haven't got a chance to take pictures of them yet. I can post them up in an hour or so. Lmk.
02-01-2016, 10:01 PM
#39
Former Vendor
Thread Starter
02-01-2016, 10:20 PM
#40
Former Vendor
Thread Starter
Blem Zr1 Style Side Skirts 1" Extended
Blem #1 (Vacuum Infused 12K 2x2) $500 Shipped. Tiny little bubbles on both of the skirts front, mid and rear part of the skirt. The bubble will not be as visible once installed. It does come with the flaps which also have tiny air pocket. The skirts are not polished, but are still shiny and very smooth.
Blem #3 (Handlaid 3K 2x2) $475 Shipped. This one has a couple open pockets on the driver side skirts where it meets the flap. The passanger side has NO bubble, but does have a hazy mark about has long as as the skirt. I know 100% it can be sanded and polished out. One of the flaps has a little chip on the bottom but that will not be visible at all once installed. The clearish haze you see on the flap which is the last picture the carbon was not pushed completely therefor leaving a bridge.
Blem #4 (Handlaid 3k 2x2) $500 shipped This one doesn't have much bubbles at all just the little ones that you see in the picture and it is only the driver side. The passenger side is clean so are the flaps.
Blem #1 (Vacuum Infused 12K 2x2) $500 Shipped. Tiny little bubbles on both of the skirts front, mid and rear part of the skirt. The bubble will not be as visible once installed. It does come with the flaps which also have tiny air pocket. The skirts are not polished, but are still shiny and very smooth.
Blem #3 (Handlaid 3K 2x2) $475 Shipped. This one has a couple open pockets on the driver side skirts where it meets the flap. The passanger side has NO bubble, but does have a hazy mark about has long as as the skirt. I know 100% it can be sanded and polished out. One of the flaps has a little chip on the bottom but that will not be visible at all once installed. The clearish haze you see on the flap which is the last picture the carbon was not pushed completely therefor leaving a bridge.
Blem #4 (Handlaid 3k 2x2) $500 shipped This one doesn't have much bubbles at all just the little ones that you see in the picture and it is only the driver side. The passenger side is clean so are the flaps.
Last edited by CF Kits & Performance; 02-01-2016 at 10:21 PM.