[Z06] New!! Two-Tone Leather Console Covers **$109.99**
10-18-2010, 07:27 AM
#1
Former Vendor
Thread Starter
Member Since: Dec 2007
Location: Ft Worth TX
Posts: 22,135
Likes: 0
Received 2 Likes
on
2 Posts
St. Jude Donor '12-'13
New!! Two-Tone Leather Console Covers **$109.99**
New at Corvette Mods!
Add a unique style and look to the interior of your C6
Our 2-Tone leather console cushions simply installs over the existing rock hard GM console pad and offers a great custom look at a very small price! Near the Bottom we also added the new embroidered console cushions with C6 logos from just $109.99.
No cutting, drilling or gluing. 100% removable at any time. Install takes minutes.
We have these Non Embroidered marked down from $129.99 for a limited time.
Click the sale link below to be taken to the special page where the Non Embroidered are marked down to $109.99
Click here to order:
http://www.corvettemods.com/C6-Corve...ne_p_5160.html
Scroll through our customers posts in this thread. You will see a lot of great customization so you can see what your C6 is capable of! We also offer matching brake and shift boots on our site to complete the look!
CLICK HERE TO GO TO ALL OF OUR LEATHER GOODS TO COMPLETE your C6!
http://www.corvettemods.com/Leather-Upgrades_c_392.html
http://www.corvettemods.com/C6-2005-...o_p_11129.html
http://www.corvettemods.com/C6-2005-...o_p_11128.html
http://www.corvettemods.com/C6-Corve...o_p_11122.html
Add a unique style and look to the interior of your C6
Our 2-Tone leather console cushions simply installs over the existing rock hard GM console pad and offers a great custom look at a very small price! Near the Bottom we also added the new embroidered console cushions with C6 logos from just $109.99.No cutting, drilling or gluing. 100% removable at any time. Install takes minutes.
We have these Non Embroidered marked down from $129.99 for a limited time.
Click the sale link below to be taken to the special page where the Non Embroidered are marked down to $109.99
Click here to order:
http://www.corvettemods.com/C6-Corve...ne_p_5160.html
Scroll through our customers posts in this thread. You will see a lot of great customization so you can see what your C6 is capable of! We also offer matching brake and shift boots on our site to complete the look!
CLICK HERE TO GO TO ALL OF OUR LEATHER GOODS TO COMPLETE your C6!
http://www.corvettemods.com/Leather-Upgrades_c_392.html
http://www.corvettemods.com/C6-2005-...o_p_11129.html
http://www.corvettemods.com/C6-2005-...o_p_11128.html
http://www.corvettemods.com/C6-Corve...o_p_11122.html
Another happy customer! We also have a full line of matching brake and shift boots too!
Last edited by corvettemods1; 12-24-2014 at 01:32 PM.
10-21-2010, 05:30 PM
#2
Le Mans Master
Member Since: Jan 2009
Location: Pottsboro; Sometimes Dallas Texas
Posts: 6,112
Likes: 0
Received 4 Likes
on
4 Posts
St. Jude Donor '12
Do you know which color red is the (red) used on Z06 interior....I have a 2010 Z06....RPO red interior. However, it's about 50-50 red/ebony.....I do NOT know which color red it is....I think it's a toss-up between victory red and magnetic red....I want one of these console covers but would like it matched to other red in cabin. I looked at build sheet and it is not indicated. Just says "RPO Red" interior. I want the one with ebony top/red sides. Just don't know which red it is. Thanks
10-21-2010, 05:51 PM
#3
Former Vendor
Thread Starter
Member Since: Dec 2007
Location: Ft Worth TX
Posts: 22,135
Likes: 0
Received 2 Likes
on
2 Posts
St. Jude Donor '12-'13
Do you know which color red is the (red) used on Z06 interior....I have a 2010 Z06....RPO red interior. However, it's about 50-50 red/ebony.....I do NOT know which color red it is....I think it's a toss-up between victory red and magnetic red....I want one of these console covers but would like it matched to other red in cabin. I looked at build sheet and it is not indicated. Just says "RPO Red" interior. I want the one with ebony top/red sides. Just don't know which red it is. Thanks
Last edited by corvettemods1; 01-20-2011 at 04:27 PM.
11-08-2010, 01:35 PM
#6
Melting Slicks
Update on this cover.
Ordered and was shipped promptly. It came in a box that would fit a pair of FRC's so the cover was superbly protected during shipping.
Went to ACE hardware and bought the #15 Torx driver ($6.99) and it took me more time to take off the car cover than it did to remove the console cover. Takes less than two minutes to remove.
Removed the 7 Torx screws that hold the existing console "pad" in less than 3 minutes.
Cleaned the edges with alcohol and let dry (takes about two minutes as well).
Cut the supplied two sided tape and add to the necessary areas. Less than 4 minutes.
Stretch and align the new padded cover over the console cover. Remove the other side of the two sided tape and press the padded cover to the tape.
Reinstall the inside panel and put back in the 7 torx screws.
Done deal!
I am telling you it took all of maybe 20 minutes to do this job. I'm going to leave the finished product indoors for a few days to keep it warm.
Pictures to follow.
Ordered and was shipped promptly. It came in a box that would fit a pair of FRC's so the cover was superbly protected during shipping.
Went to ACE hardware and bought the #15 Torx driver ($6.99) and it took me more time to take off the car cover than it did to remove the console cover. Takes less than two minutes to remove.
Removed the 7 Torx screws that hold the existing console "pad" in less than 3 minutes.
Cleaned the edges with alcohol and let dry (takes about two minutes as well).
Cut the supplied two sided tape and add to the necessary areas. Less than 4 minutes.
Stretch and align the new padded cover over the console cover. Remove the other side of the two sided tape and press the padded cover to the tape.
Reinstall the inside panel and put back in the 7 torx screws.
Done deal!
I am telling you it took all of maybe 20 minutes to do this job. I'm going to leave the finished product indoors for a few days to keep it warm.
Pictures to follow.
11-10-2010, 06:15 PM
#7
Former Vendor
Thread Starter
Member Since: Dec 2007
Location: Ft Worth TX
Posts: 22,135
Likes: 0
Received 2 Likes
on
2 Posts
St. Jude Donor '12-'13
Thanks Al! 
Update on this cover.
Ordered and was shipped promptly. It came in a box that would fit a pair of FRC's so the cover was superbly protected during shipping.
Went to ACE hardware and bought the #15 Torx driver ($6.99) and it took me more time to take off the car cover than it did to remove the console cover. Takes less than two minutes to remove.
Removed the 7 Torx screws that hold the existing console "pad" in less than 3 minutes.
Cleaned the edges with alcohol and let dry (takes about two minutes as well).
Cut the supplied two sided tape and add to the necessary areas. Less than 4 minutes.
Stretch and align the new padded cover over the console cover. Remove the other side of the two sided tape and press the padded cover to the tape.
Reinstall the inside panel and put back in the 7 torx screws.
Done deal!
I am telling you it took all of maybe 20 minutes to do this job. I'm going to leave the finished product indoors for a few days to keep it warm.
Pictures to follow.
Ordered and was shipped promptly. It came in a box that would fit a pair of FRC's so the cover was superbly protected during shipping.
Went to ACE hardware and bought the #15 Torx driver ($6.99) and it took me more time to take off the car cover than it did to remove the console cover. Takes less than two minutes to remove.
Removed the 7 Torx screws that hold the existing console "pad" in less than 3 minutes.
Cleaned the edges with alcohol and let dry (takes about two minutes as well).
Cut the supplied two sided tape and add to the necessary areas. Less than 4 minutes.
Stretch and align the new padded cover over the console cover. Remove the other side of the two sided tape and press the padded cover to the tape.
Reinstall the inside panel and put back in the 7 torx screws.
Done deal!
I am telling you it took all of maybe 20 minutes to do this job. I'm going to leave the finished product indoors for a few days to keep it warm.
Pictures to follow.
12-23-2010, 01:34 PM
#9
Drifting
Do you know which color red is the (red) used on Z06 interior....I have a 2010 Z06....RPO red interior. However, it's about 50-50 red/ebony.....I do NOT know which color red it is....I think it's a toss-up between victory red and magnetic red....I want one of these console covers but would like it matched to other red in cabin. I looked at build sheet and it is not indicated. Just says "RPO Red" interior. I want the one with ebony top/red sides. Just don't know which red it is. Thanks
03-04-2011, 09:47 PM
#12
Former Vendor
Thread Starter
Member Since: Dec 2007
Location: Ft Worth TX
Posts: 22,135
Likes: 0
Received 2 Likes
on
2 Posts
St. Jude Donor '12-'13
Came home from my latest trip to find that my favorite guys in the brown truck delivered me some goodies. Amongst the feast of mods was the two tone (Black/Titanium) leather console cover I ordered from CorvetteMods.com. The color was a perfect match and the install was pretty easy. The leather is a nice tight fit and needed a little persuasion from a hair dryer, which was actually a good thing because as it cooled down it made for a superb fit over the stock console lid. The whole install took less than an hour and as you can see below I think the results came out very nice.
Nice product, very happy with the results. Now off to the next mod
Nice product, very happy with the results. Now off to the next mod
11-04-2011, 11:28 AM
#15
Instructor
Member Since: Sep 2011
Location: Lansdale PA
Posts: 185
Likes: 0
Received 0 Likes
on
0 Posts
I just installed it in my Z06. Great product and nice addition to my Z interior. I love the smell of new leather too! Their customer service is also very nice. I ordered wrong color at first but they shipped right one without any additional charge.
Here are the pics.
Their customer service is also very nice. I ordered wrong color at first but they shipped right one without any additional charge. Here are the pics.
09-20-2012, 08:29 PM
#17
Guys, do you offer a stock black with red stitching 07 shift ****? I am looking to buy shift boot, e-brake handle with boot and center console cover. Not looking for two tone, just black with red stitching. Do you offer all these matching pieces? My vr z has red seat inserts, not sure what red it is though on the interior.
Thanks!
Thanks!
09-20-2012, 11:03 PM
#18
Former Vendor
Thread Starter
Member Since: Dec 2007
Location: Ft Worth TX
Posts: 22,135
Likes: 0
Received 2 Likes
on
2 Posts
St. Jude Donor '12-'13
Guys, do you offer a stock black with red stitching 07 shift ****? I am looking to buy shift boot, e-brake handle with boot and center console cover. Not looking for two tone, just black with red stitching. Do you offer all these matching pieces? My vr z has red seat inserts, not sure what red it is though on the interior.
Thanks!
Thanks!
09-21-2012, 12:44 AM
#19
09-21-2012, 01:06 AM
#20
Former Vendor
Thread Starter
Member Since: Dec 2007
Location: Ft Worth TX
Posts: 22,135
Likes: 0
Received 2 Likes
on
2 Posts
St. Jude Donor '12-'13
http://www.corvettemods.com/Corvette...es_p_5590.html
For the ****, inferno orange really looks red. Fyi
