[Z06] Mamo H/C/I install...Who should I have do it?
#1
Racer
Thread Starter
Mamo H/C/I install...Who should I have do it?
I have a question for everyone on here. I've been working with Tony for a while on this and I've got most of the parts. Here is the list:
MMS 265 TFS heads
Manton Custom Length Pushrods
Johnson Lifters
Yella Terra MMS Ultralite Shaftrockers
Cam
MSD
NW102
ARH 2" Headers with Cats
ATI Damper
Bosch Injectors
Ported ZR1 Pump
Katech C5-R Chain
MMS RPS Lightened BC2 Clutch with Katech Remote Bleeder
I'm looking for a good installer and tuner. I need to find a place that is willing to install parts that I've purchased from Tony. I'm in the Midwest but I'm willing to haul to car somewhere (within reason). I just want the install and the tune done right. There is a lot of money in that list so I want to make sure everything is done right.
Can anyone point me in the direction of a high quality shop for the install and tune?
Thanks!
MMS 265 TFS heads
Manton Custom Length Pushrods
Johnson Lifters
Yella Terra MMS Ultralite Shaftrockers
Cam
MSD
NW102
ARH 2" Headers with Cats
ATI Damper
Bosch Injectors
Ported ZR1 Pump
Katech C5-R Chain
MMS RPS Lightened BC2 Clutch with Katech Remote Bleeder
I'm looking for a good installer and tuner. I need to find a place that is willing to install parts that I've purchased from Tony. I'm in the Midwest but I'm willing to haul to car somewhere (within reason). I just want the install and the tune done right. There is a lot of money in that list so I want to make sure everything is done right.
Can anyone point me in the direction of a high quality shop for the install and tune?
Thanks!
#4
Actually its a 242/256 on a 114 + 3
(Typed the wrong digit on the estimate Ryan....sorry bout that!)
Make sure your cam card reads the same because the 256 is what I wanted and what I instructed Comp to cut for you.
--------------------------------------------------------------------------------------------------------------------------------------
Guys.....help out a fellow C6Z brother with some input on some shops that are good to work with in the middle of the country!
I encouraged Ryan to post hoping a few of you guys would chime in!
Cheers,
Tony
(Typed the wrong digit on the estimate Ryan....sorry bout that!)
Make sure your cam card reads the same because the 256 is what I wanted and what I instructed Comp to cut for you.
--------------------------------------------------------------------------------------------------------------------------------------
Guys.....help out a fellow C6Z brother with some input on some shops that are good to work with in the middle of the country!
I encouraged Ryan to post hoping a few of you guys would chime in!
Cheers,
Tony
__________________
Please take the time to also visit my website at www.MamoMotorsports.com
Please take the time to also visit my website at www.MamoMotorsports.com
Last edited by Tony @ Mamo Motorsports; 04-23-2017 at 02:55 AM.
#5
Melting Slicks
Member Since: Jun 2005
Location: Rochester NY
Posts: 2,734
Received 1,678 Likes
on
878 Posts
2018 C6 of Year Finalist
St. Jude Donor '10, '17
Sounds like a superb build. You are in the best of hands with Tony. If it's me, I would make the drive to Doug Rippie Motorsports (DRM) in Minnesota.
#9
Racer
Thread Starter
#13
Le Mans Master
Originally Posted by Whis9
Where is your location I cannot see on my phone
#14
Burning Brakes
Actually its a 242/256 on a 114 + 3
(Typed the wrong digit on the estimate Ryan....sorry bout that!)
Make sure your cam card reads the same because the 256 is what I wanted and what I instructed Comp to cut for you.
--------------------------------------------------------------------------------------------------------------------------------------
Guys.....help out a fellow C6Z brother with some input on some shops that are good to work with in the middle of the country!
I encouraged Ryan to post hoping a few of you guys would chime in!
Cheers,
Tony
(Typed the wrong digit on the estimate Ryan....sorry bout that!)
Make sure your cam card reads the same because the 256 is what I wanted and what I instructed Comp to cut for you.
--------------------------------------------------------------------------------------------------------------------------------------
Guys.....help out a fellow C6Z brother with some input on some shops that are good to work with in the middle of the country!
I encouraged Ryan to post hoping a few of you guys would chime in!
Cheers,
Tony
Sorry I don't have a shop to recommend for your area. I'd lend a hand and loan you a few special tools if you were in the North Mississippi area.