CorvetteForum - Chevrolet Corvette Forum Discussion

C7 Forced Induction/Nitrous C7 Corvette Turbochargers, Superchargers, Pulley Upgrades, Intercoolers, Wet and Dry Nitrous Injection, Meth
Sponsored by:
Sponsored by:

My 2017 A&A + METH Setup

   
Old 05-15-2017, 08:54 PM
  #21  
WarHammer619
Instructor
Thread Starter
 
WarHammer619's Avatar
 
Member Since: May 2017
Location: San Diego CA
Posts: 144
Received 13 Likes on 13 Posts
Default
Originally Posted by robert miller
The dyno should only be used to give a person a some what good WOT tune on the car, Not doing that on the street when a person get in the 800 to 1,k and over set up. Plus on the side you a rwhp & rwtq #. But a track will get the car truly dialed in under a true load. Robert
Absolutely agree. We always Log the 1/2 mile runs to improve where we can. At the end of the day, I am coming from a Procharged Challenger. This is better in SO many ways!!!!
WarHammer619 is offline  
Reply Like
Old 05-15-2017, 09:24 PM
  #22  
Dfwz06
Burning Brakes
 
Dfwz06's Avatar
 
Member Since: Jul 2014
Location: Midlothian Texas
Posts: 791
Received 142 Likes on 111 Posts
Default
You're boost numbers are a bit higher cause you're on stock manifolds. Just ignore the negative reviews and enjoy your new found power.
Dfwz06 is offline  
Reply Like
The following users liked this post:
WarHammer619 (05-15-2017)
Old 05-15-2017, 09:24 PM
  #23  
Dfwz06
Burning Brakes
 
Dfwz06's Avatar
 
Member Since: Jul 2014
Location: Midlothian Texas
Posts: 791
Received 142 Likes on 111 Posts
Default
I'm at 21lbs of boost due to stock manifolds and stock cam. I should be around 16lbs.
Dfwz06 is offline  
Reply Like
The following users liked this post:
WarHammer619 (05-15-2017)
Old 05-15-2017, 10:13 PM
  #24  
WarHammer619
Instructor
Thread Starter
 
WarHammer619's Avatar
 
Member Since: May 2017
Location: San Diego CA
Posts: 144
Received 13 Likes on 13 Posts
Default
Originally Posted by Dfwz06
You're boost numbers are a bit higher cause you're on stock manifolds. Just ignore the negative reviews and enjoy your new found power.
Thanks man. Just like every group I have been apart of, if you don't show a DYNO graph you are a liar, If you do it must be wrong. Hahahah, I am just blessed to have worked hard for a car like this at my point in life.
WarHammer619 is offline  
Reply Like
Old 05-15-2017, 10:57 PM
  #25  
WarHammer619
Instructor
Thread Starter
 
WarHammer619's Avatar
 
Member Since: May 2017
Location: San Diego CA
Posts: 144
Received 13 Likes on 13 Posts
Default
Originally Posted by Dfwz06
I'm at 21lbs of boost due to stock manifolds and stock cam. I should be around 16lbs.
BTW, your setup on the Z is insane!!!!!! I had a D1-R on my Challenger. cant imagine an F1R on a Z!!!!!!!!!!
WarHammer619 is offline  
Reply Like
Old 05-16-2017, 09:55 AM
  #26  
Dfwz06
Burning Brakes
 
Dfwz06's Avatar
 
Member Since: Jul 2014
Location: Midlothian Texas
Posts: 791
Received 142 Likes on 111 Posts
Default
Thanks. Good luck
Dfwz06 is offline  
Reply Like
Old 05-17-2017, 11:10 PM
  #27  
Boomscatty
Advanced
 
Boomscatty's Avatar
 
Member Since: Mar 2017
Posts: 53
Received 5 Likes on 4 Posts
Default
Originally Posted by C7&7
The T trim is the bigger head unit. He is probably right about 9-10 psi which is the right power for what he saw with meth. It'll be a 680 rwhp car with headers. That is basically the identical setup to the novi 1500 headers and meth cars which we see 680-700 wheel all day long.
My 2014 Z51 laid down 698whp and 637tq on an AA Ti with 2" Kooks, 3" X-pipe catless and methanol .
Boomscatty is offline  
Reply Like
The following users liked this post:
WarHammer619 (05-18-2017)
Old 05-18-2017, 12:58 AM
  #28  
WarHammer619
Instructor
Thread Starter
 
WarHammer619's Avatar
 
Member Since: May 2017
Location: San Diego CA
Posts: 144
Received 13 Likes on 13 Posts
Default
Originally Posted by Boomscatty
My 2014 Z51 laid down 698whp and 637tq on an AA Ti with 2" Kooks, 3" X-pipe catless and methanol .
HOLY ****!!!
WarHammer619 is offline  
Reply Like
Old 05-18-2017, 06:32 AM
  #29  
0Quik Z06
Former Vendor
 
Quik Z06's Avatar
 
Member Since: Oct 2003
Location: Devil's Island CA
Posts: 8,479
Received 411 Likes on 280 Posts

Default
Originally Posted by WarHammer619
Thanks for all the opinions, again the final number doesn't mean much. With the racing I do it will speak for itself on the 1/2 mile. First race for this car will be in November.
You running at Shift Sector? I believe they have an event in October, I should be running at that event. Getting ready to do the Si-V3 on my 14 Z51, I might be getting it done at A&A as well.
Last edited by Quik Z06; 05-18-2017 at 06:33 AM.
Quik Z06 is offline  
Reply Like
The following users liked this post:
WarHammer619 (05-19-2017)
Old 05-19-2017, 06:15 PM
  #30  
WarHammer619
Instructor
Thread Starter
 
WarHammer619's Avatar
 
Member Since: May 2017
Location: San Diego CA
Posts: 144
Received 13 Likes on 13 Posts
Default
Originally Posted by Quik Z06
You running at Shift Sector? I believe they have an event in October, I should be running at that event. Getting ready to do the Si-V3 on my 14 Z51, I might be getting it done at A&A as well.
Yes I will be. The company i work with is a Shift Sector Sponsor so both the owner and I run. I absolutely recommend talking to josh at A&A.
Last edited by WarHammer619; 05-19-2017 at 06:17 PM.
WarHammer619 is offline  
Reply Like
Old 05-19-2017, 06:20 PM
  #31  
FYREANT
I'm Batman..
Pro Mechanic
Support Corvetteforum!
 
FYREANT's Avatar
 
Member Since: Apr 2014
Location: Lehigh Acres FL
Posts: 6,130
Received 908 Likes on 561 Posts
Tech Contributor

Default
Originally Posted by WarHammer619
Yes I will be. The company i work with is a Shift Sector Sponsor so both the owner and I run. I absolutely recommend talking to josh at A&A.
I talked to Josh yesterday actually Lol. Bought a T trim kit to upgrade my Si trim
FYREANT is offline  
Reply Like
Old 05-19-2017, 07:35 PM
  #32  
robert miller
Team Owner
 
robert miller's Avatar
 
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes on 1,529 Posts

Default
Originally Posted by FYREANT
I talked to Josh yesterday actually Lol. Bought a T trim kit to upgrade my Si trim
Buddy glad you finally got one even if you got new. Going the fFL on vacation for 2 weeks get it on & tuned so I know what # to be looking for when I get back & get the car to my tuner.
robert miller is offline  
Reply Like
Old 05-19-2017, 08:33 PM
  #33  
FYREANT
I'm Batman..
Pro Mechanic
Support Corvetteforum!
 
FYREANT's Avatar
 
Member Since: Apr 2014
Location: Lehigh Acres FL
Posts: 6,130
Received 908 Likes on 561 Posts
Tech Contributor

Default
Originally Posted by robert miller
Buddy glad you finally got one even if you got new. Going the fFL on vacation for 2 weeks get it on & tuned so I know what # to be looking for when I get back & get the car to my tuner.
My car may not be a good comparison unless you are building for 900whp or more..
FYREANT is offline  
Reply Like
Old 05-19-2017, 10:57 PM
  #34  
robert miller
Team Owner
 
robert miller's Avatar
 
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes on 1,529 Posts

Default
Originally Posted by FYREANT
My car may not be a good comparison unless you are building for 900whp or more..
Forgot you got the diff block. Cant wait to see what she does for you on the track.
robert miller is offline  
Reply Like
Old 05-20-2017, 12:31 PM
  #35  
Silverboost
Racer
 
Silverboost's Avatar
 
Member Since: Nov 2008
Posts: 495
Received 50 Likes on 44 Posts

Default
Many times headers add less than you would think on our cars but the side effect is they sound bad ***!!
Silverboost is offline  
Reply Like
The following users liked this post:
WarHammer619 (06-17-2017)
Back to Subforum
C7 Forced Induction/Nitrous
View Next Unread
Johnny O'Connell Stage 1 Signature Series Suspension Kits - C7


Thread Tools
Search this Thread
Search this Thread:

Click for Advanced Search

Click for Advanced Search
Quick Reply: My 2017 A&A + METH Setup


Reply Closed Thread Share
Forum Jump
Trending Topics

All times are GMT -4. The time now is 03:43 AM.