New build on the C7 with A/A TI unit
#21
Team Owner
Thread Starter
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes
on
1,529 Posts
Thanks man for the remark it will have all some of the best parts in the rear end trans & motor. For no more rwhp power hoping it will hold together but will push it for meth 38% BTR stage II cam with the LT4 inj & pump. This will be as far as I will push the power level with a good tune on it.
Also the car is at the shop up in KNOXVILLE, TN as of today cant wait to get it back from Nick.. Will get some pic's as it come along with the work.. Robert
Also the car is at the shop up in KNOXVILLE, TN as of today cant wait to get it back from Nick.. Will get some pic's as it come along with the work.. Robert
#23
Team Owner
Thread Starter
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes
on
1,529 Posts
Well have every part of the running gear & motor out of the car. Was just told new motor will be done by tomorrow. Robert
Last edited by robert miller; 01-01-2019 at 07:17 PM.
#24
Team Owner
Thread Starter
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes
on
1,529 Posts
ttt
some pic's of the car & motor at Nicks shop getting worked on..
The following users liked this post:
FYREANT (01-05-2019)
#25
Bucking/surging when slowing down for a stop....I am ok with it but wish I had put a converter in it for better 60ft times when the diff was out for a Wavetrac
Last edited by Jaycajun; 01-06-2019 at 12:53 PM.
#26
Team Owner
Thread Starter
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes
on
1,529 Posts
I agree I know the 3200 stall will not be enough for a full track car but it is more of a street car for me. I just hope with the LG solid motor and trans mounts, & the 3 1/4 inch C.F. driveshaft with no couplers on it that the car is not to bad on the street. We will see when it is all together. Robert
#29
Team Owner
Thread Starter
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes
on
1,529 Posts
The following users liked this post:
FYREANT (01-14-2019)
#30
Team Owner
Thread Starter
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes
on
1,529 Posts
Think you man for the kinds words. Hope to have it all done by next month sometime now have gotten all my parts in now. Got the C.F. driveshaft into the tq tube has no couplers on it with the Circle D stall also..Robert
Last edited by robert miller; 01-16-2019 at 11:08 PM.
#31
Team Owner
Thread Starter
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes
on
1,529 Posts
ttt
Motor almost going into the car
#33
Team Owner
Thread Starter
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes
on
1,529 Posts
#36
Team Owner
Thread Starter
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes
on
1,529 Posts
#38
Team Owner
Thread Starter
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes
on
1,529 Posts
I hope so the motor will be going onto the stand along engine stand within the next week are so just needed some fittings to make the way into the shop. Going to be running it on the stand to make sure all is good before putting all together back on the cradle & back into the car.. Robert
#39
I hope so the motor will be going onto the stand along engine stand within the next week are so just needed some fittings to make the way into the shop. Going to be running it on the stand to make sure all is good before putting all together back on the cradle & back into the car.. Robert
#40
Team Owner
Thread Starter
Member Since: Jan 2007
Location: cookeville tennessee
Posts: 28,846
Received 1,762 Likes
on
1,529 Posts
ttt
You can buy a stand along set up but for the C7 it is about 2200.00 to be able to run it on a stand. So dam much more to this new c7 set up the c5 & c6 is about half that price. Just have to set up a tune in it to get the car to start is all will not be running no big RPM at all. Just making sure it runs and has no leaks much better than seeing something is wrong after you have this part back into the car.. Robert