What hardware do I need to install NoviStretch Bra?
#1
Drifting
Thread Starter
What hardware do I need to install NoviStretch Bra?
Help. I bough the C7-Corvette NoviStretch-Bra-Front-Bumper Mask many years ago and never installed. I've since lost the hardware.
Can anyone update me on the hardware needed? How many snaps do I need? Can I buy these snaps from Home Depot?
Thanks in advance!
Can anyone update me on the hardware needed? How many snaps do I need? Can I buy these snaps from Home Depot?
Thanks in advance!
#2
E-Ray, 3LZ, ZER, LIFT
Member Since: Sep 2007
Location: NE South Carolina
Posts: 29,447
Received 9,605 Likes
on
6,618 Posts
^^^
I had a similar need as I sold my 2014 with the original NovaStretch bra hardware and recently installed new hardware I bought for my Grand Sport. I kept the bra.
This is a PDF that describes my install and sources:
http://netwelding.com/Nylon_Bra.pdf
Probably won't find the hardware locally but you'll see the source I used in the PDF. Amazon carries the stainless steel snaps with sheet metal screws. They come with various length screws. You'll need 3 each side for the fenders and two for the bottom. Install the sides, snap in the Bra and then pull in udder the bumper and locate where those two snaps go.
You'll see I installed with the a splitter on my 2014 C7 and on my Grand Sport even with Stage 3 winglets. The same Marine accessories store that sells the stainless male snaps also sells snap extensions in various lengths. I had used these on m Pontoon boat cover as they shrink over time!m For the sStage 3 Winglets I only needed one on the lower snap on both sides.
I had a similar need as I sold my 2014 with the original NovaStretch bra hardware and recently installed new hardware I bought for my Grand Sport. I kept the bra.
This is a PDF that describes my install and sources:
http://netwelding.com/Nylon_Bra.pdf
Probably won't find the hardware locally but you'll see the source I used in the PDF. Amazon carries the stainless steel snaps with sheet metal screws. They come with various length screws. You'll need 3 each side for the fenders and two for the bottom. Install the sides, snap in the Bra and then pull in udder the bumper and locate where those two snaps go.
You'll see I installed with the a splitter on my 2014 C7 and on my Grand Sport even with Stage 3 winglets. The same Marine accessories store that sells the stainless male snaps also sells snap extensions in various lengths. I had used these on m Pontoon boat cover as they shrink over time!m For the sStage 3 Winglets I only needed one on the lower snap on both sides.
Last edited by JerryU; 09-16-2017 at 03:08 AM.
#4
I have an extra set PM sent .....
#6
Drifting
Thread Starter
Guys and gals, please help me extend a warm, 'Thank You" to fellow member bbrown450.
He was nice enough to send me (for free) an extra set of snaps so I could attach my Novistretch bra.
AND, he refused to let me pick up the shipping cost!
Listen, there is a lot of hate in this world.
It's reassuring to know that there are some people out there that are nice and thoughtful......and they can be a perfect stranger to you.
Remember to always Pay It Forward. You never know when it'll come full circle to you.
Thanks bbrown450
He was nice enough to send me (for free) an extra set of snaps so I could attach my Novistretch bra.
AND, he refused to let me pick up the shipping cost!
Listen, there is a lot of hate in this world.
It's reassuring to know that there are some people out there that are nice and thoughtful......and they can be a perfect stranger to you.
Remember to always Pay It Forward. You never know when it'll come full circle to you.
Thanks bbrown450
The following users liked this post:
Strake (09-22-2017)