RPIDON

C7 Corvette Stingray NoviStretch Front Bumper Mask

From the makers of the Original Stretch-to-Fit bras and mirror covers, NoviStretch Performance Protective Covers are available for your 2014-2018 C7 Corvette Stingray. Only available in color BLACK.

This C7 Corvette front bumper mask features:
*Synthetic Stretch Mesh Fabric
*Heavy Duty Elastic Trim
*All Black "Hidden" Hardware
*Snap and Strap Installation
*Patent Pending Design
*100% Manufactured in USA
*12 Month Limited Warranty

This C7 Corvette Stretch Mask is a great solution for those Corvette owners that do not want to drill into their brand new Stingray. This mask is a very easy installation and can be removed without any permanent modifications to your car. Once installed you can quickly remove the NoviStretch mask and store it in your Corvette's glove box. Once installed, you can put on and take off in a matter of minutes.

Please note, these are currently in production and will ship out on June 16, 2014. We are starting to take preorders and they will ship as soon as they can. Get your order in ASAP because the bugs are waiting for you!!

Item # FBM750V Use Coupon Code RPICHRIS5 on line or by phone when ordering and receive 5% off the listed website price!!

Website Link : http://www.rpidesigns.com/shop/item.aspx?itemid=4854

RPI Designs

More pictures for you guys:

RPI Designs

RPI Designs

Installation Instructions:

Tools Required: Short handle Philips screwdriver; #15 Torx head screwdriver; socket wrench; 7mm socket

SPECIAL INSTALLATION INSTRUCTIONS
Front License Plate Installation– A front license plate may be installed over the mask without causing harm to the mask. The small holes made by the mounting screws will not cause
the fabric to “run”. Thumbscrews may be used to make the removal of the license plate more convenient.

CLEANING AND CARE INSTRUCTIONS
• The mask can be cleaned by rinsing in water to remove any dirt or debris then squeezing the water out and let air-dry. Wash (by hand) only as necessary. Use a concentrated soap solution
on areas of the mask that may be particularly dirty.

• Always ensure areas covered by the mask are clean and free of sand and grit before installing the mask.

• For the best life do not leave the mask on the car while parked in the sun for extended periods.

• Avoid obstacles and low clearance areas in the roadway that may come in contact with the bottom of the car causing the mask to snag and the material to tear.

Step #1
Clean the bumper and surfaces under the car and the fender wells thoroughly (tar and grease remover
is recommended).

Step #2
Turn the front wheels to gain easier access to the fender liner mounting screws that you will be
replacing.

Step #3
Locate the mounting screws at the edge of the bumper inside the fender liner and remove them. Replace
each one as you go with the supplied snap-head screw studs. Repeat this step on the other side of the
car.

Step #4
Begin the installation by fastening the snaps on one end of the mask to the screws just installed
on the edge of the bumper.

Step #5
Stretch the mask across the front of the bumper and attach to the other side of the car.
Note: the tension in the mask is normal and important to the overall performance of the product.

Step #6
Pull the bottom edge of the mask down under the bumper, noting the position of the snaps on the
bottom edge of the mask. Replace the screws on the bottom of the bumper that best align with the
snaps on the mask with a snap head screw stud. Fasten the snaps on bottom of the mask to the
screws just installed on the bottom of the bumper.

Step #7
Locate and slightly loosen the screw holding the corner of the air dam on each side of the car allowing the
bottom edge of the mask to go between the bumper and the air dam. Note: This step is optional but
recommended for best fit.

Step #8 & #9
Open the hood and remove the plastic covering at each corner to expose the corner edge
of the body frame just inside the hood opening. [This piece is held in place with friction clips
and is easily removed by prying it loose with your hand]. Repeat this step for the other corner
of the mask. Holding the top of the mask pull it up to the hood opening and secure each
corner of the mask to the body frame

Steve Garrett

RPI Designs

Thanks again for the order!

RPIDON

A great and easy way of protecting the front of your C7!!

Mike Campbell

I will be placing an order before the end of May along with the mirror covers too. Just waiting for a check.

RPIDON

Warm weather is finally here , that means the bugs are out, get one of these and your front bumper and grille will thank you!!

RPIDON

Makes a Great Christmas Gift!!

RPI Designs

Mike Campbell

Well I finally got my NoviStretch Bra & Mirror masks and put them on today. I noticed a little note that said if I had any pictures to send them to you guys. Well, here they are. I know these won't protect from large flying objects, but, bugs and other smaller nasty projectiles are what I'm counting on.







and I don't think they look that bad on my white Stingray.

RPI Designs

Your car looks great! Thanks for posting some pictures!

RPI Designs

RPI Designs

Thank you for the orders! Use coupon code LANA5 to save 5% off your order!

RPIDON

Use Coupon Code RPICHRIS5 at Checkout for an Immediate Savings!!!

RPIDON

Thank you for the orders!

RPIDON

Use Coupon Code RPICHRIS5 for an Immediate Discount!

RPIDON

Thank You for shopping at https://www.rpidesigns.com/shop/item.aspx?itemid=4854 using Anuran5 code

RPI Designs

Thank You for shopping at https://www.rpidesigns.com/shop/item.aspx?itemid=4854 using Anuran5 code