2300 Club!
#161
#165
Burning Brakes
Did any other diy'ers notice the alignment pins/dowels for the lid were missing? I see the holes for them but no pins. I checked the blower, lid, my workbench, and entire floor of my garage and have not found them. Curious if anyone else noticed theres missing, and if not, do you know what they're made of? Metal or plastic? Thanks!
The following users liked this post:
Mikec7z (03-21-2019)
#166
Melting Slicks
Member Since: Nov 2000
Location: Merritt Island Florida
Posts: 2,225
Received 241 Likes
on
145 Posts
My pins where also missing, but i got info from Magnuson, it is done by purpose.... to avoid people dropping them into engine :-)
On another note.... there is a temp sensor passenger side, right behind the vacuum operated bypass valve, but there is not a piggy back harness that let me connect it to my wiring harness ?
anyone know what's up with that ?
tia
Rune
On another note.... there is a temp sensor passenger side, right behind the vacuum operated bypass valve, but there is not a piggy back harness that let me connect it to my wiring harness ?
anyone know what's up with that ?
tia
Rune
The following users liked this post:
Mikec7z (03-21-2019)
#167
Should have included a breakout harness for the TMAP connector, shoot a note to Magnuson and let them know it was missing,
It provides much better temp response than the TMAP.
It provides much better temp response than the TMAP.
The following users liked this post:
Z06Norway (03-25-2019)
#168
Instructor
Hey guys!
Taking my 17’ m7 z06/07 for cam/headers/ flex fuel/ pully.... it already has an Akro evo exhuast, cai, and ported tb.... this car is going to be road coursed....
‘’should I consider upgrading the supercharger to the 2300 to keep the engine temps down?
Or should I just enjoy those mods and upgrade that next year? Thanks!
Taking my 17’ m7 z06/07 for cam/headers/ flex fuel/ pully.... it already has an Akro evo exhuast, cai, and ported tb.... this car is going to be road coursed....
‘’should I consider upgrading the supercharger to the 2300 to keep the engine temps down?
Or should I just enjoy those mods and upgrade that next year? Thanks!
#169
Melting Slicks
Member Since: Nov 2000
Location: Merritt Island Florida
Posts: 2,225
Received 241 Likes
on
145 Posts
Anyone with a 2300 that can help out ?
There is no instructions on where to put this MAP sensor ?
Passenger side at rear of supercharger
And front of SC, passenger side there is a temp sensor under IC brick water in/out , how and where does it go into wiring harness ?
Anyone with a 2300 that can give advice and help out ?
Started her up with a bunch of error codes, P0033, P0034, P10BC, P227C, P3401 P3425, P3441, P3449.
Passenger side at rear of supercharger
And front of SC, passenger side there is a temp sensor under IC brick water in/out , how and where does it go into wiring harness ?
Anyone with a 2300 that can give advice and help out ?
Started her up with a bunch of error codes, P0033, P0034, P10BC, P227C, P3401 P3425, P3441, P3449.
#170
Great temperature sensor wire
Looking at my car the gray temperature sensor does not get plugged in as far as the other sensor I don't see one at all on my car had mine professionally installed to
The following users liked this post:
Z06Norway (03-29-2019)
#171
where is JHebert when you need him?
As far as a breakout baro sensor goes (not sure if that is what you might have or not) the ambient baro sensor is normally inside the MAF, but if it is broken out via a breakout harness, then it is just mounted anywhere in the engine bay.
If you are not talking about the ambient baro sensor breakout harness, and instead you are talking about temperature sensors, one of these guys who have used this blower are going to have to help you out.
As far as a breakout baro sensor goes (not sure if that is what you might have or not) the ambient baro sensor is normally inside the MAF, but if it is broken out via a breakout harness, then it is just mounted anywhere in the engine bay.
If you are not talking about the ambient baro sensor breakout harness, and instead you are talking about temperature sensors, one of these guys who have used this blower are going to have to help you out.
The following users liked this post:
Z06Norway (03-29-2019)
#172
2300 installed 2016 ZO6
As far as the first top sensor I do not have that in my alarm ring harness and for the gray temperature sensor mine is not plugged in it just laying there and I had to buy and professionally installed
The following users liked this post:
Z06Norway (03-29-2019)
#173
Racer
2 Questions
- Is the stock C7 Z06 Crank pulley pinned or keyed?
- Does the 2300 upgrade for a Z06 require pinning of the crank/pulley?
Thanks
- Is the stock C7 Z06 Crank pulley pinned or keyed?
- Does the 2300 upgrade for a Z06 require pinning of the crank/pulley?
Thanks
Last edited by Perf n Restore; 03-30-2019 at 07:27 AM. Reason: added "keyed"
#174
Burning Brakes
#175
Last edited by cajunboyz; 10-06-2019 at 03:35 PM.
#176
Very interested in this, & i read ALOT but still have questions. I have a 2016 A8 ZO6. If i go 2300, with 2" LT headers,No cats, X pipe to rear stock mufflers, AFE or Hallteck, Good tune on 93octane, 95-103 or whatever TB, I am @ sea level(south Louisiana) will i be around 690-700RWHP ??? If i install a pulley on this set up, will I have trouble with IAT's as compared to the Stock blower set up?? Oh car is mainly for Straight Line burst, roll ons, 50 or 60 - 180 or so..( not tracked where i can see heat soak might be more of a problem)
#177
#178
Drifting
Added a ported snout with a ZR1 95mm TB to my 2300. Again I have kook headers Afe intake, 5% lower pulley XTank,and tuned. Picked up 23/25rw with the snout and Tb. Brought me up to 702/734. Throttle response is instant. Well worth the up graded Tb.
the car is a 2016 Z06 m7
the car is a 2016 Z06 m7
#179
Added a ported snout with a ZR1 95mm TB to my 2300. Again I have kook headers Afe intake, 5% lower pulley XTank,and tuned. Picked up 23/25rw with the snout and Tb. Brought me up to 702/734. Throttle response is instant. Well worth the up graded Tb.
the car is a 2016 Z06 m7
the car is a 2016 Z06 m7
#180
Yall ported the stock snout, or a different snout.. Also thought I read where the Bigger TB's 103, 0r even bigger had picked up even more RWHP. Just on the fence on if to do the 2300 with all the lil tricks or put a 2650 on er