When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Does anyone have any concave or deep dish wheels on their Z06? If so, what do you have and can you provide some pics? I'm having a SUPER hard time finding wheels that fit as no one seems to carry wheels in our bolt pattern and offset. I feel like there should be a whole forum subcategory about wheels since I see so many aftermarket ones all over the forum. At the very least there should be a sticky!
I have a few different sets and depending on the price you want to spend there are a myriad of options available.
I have ACE Alloy AFF02 (19, 20), Stance SF03 (20, 20), Signature Forged SV305S (20, 21).
Google each of those and you can see pics and vendors for all these wheels are on this forum.
I looked at all of those and none of them are deep dish, and maybe it's just the angle I'm seeing but none of them look terribly concave. Maybe just slightly. Also the sig forged ones look like stock z06 wheels.i did see the ace alloy aff06 wheels and those are ok. Might have to go with those, but I don't love them.
Again, maybe I'm just not getting a good angle but I looked at all the wheels on their site and none were concave enough for me to notice. Their flagship series had a bit of a lip, but I wouldn't call it deep dish, plus they're all pretty ugly (though I'm not counting that. Don't expect anyone to know my taste)
AVANT GARDE WHEELS m580 it seems. 19” front 20” rear. I’d have to pull the wheels to find out exact offset and width but I Run the same 285 and 335 tires. Bought the car as it sits so I’m still figuring out all of the mods specifically.
Get ahold of Gerry cw4l or Khoa at Signature Forged, either one will get what you need. Dont buy cheap wheels to save a 1k or 2k now, you will end up spending more to replace the cheaper ones later, ask me how i know. Both are excellent!
Much to the point of what's been said above, the Chevrolet Corvette has notoriously high wheel offsets. The higher the offset, the less concave a wheel will be. In addition to that, if you want the deepest dish possible the center of the wheel has to be flat. The more concave you make the center face of a 3-piece wheel the more it robs you from the amount of dish you get.
Over the years we have help set up hundreds of Corvette's and our gallery can be seen here - https://wheelsboutique.com/gallery/chevrolet/pics/chevrolet-corvette. We focus on premium custom forged wheels built here in the U.S. An American legend like the Corvette deserves wheels built here. If you'd like more information & explanation on what's possible with your Corvette send me over a quick email and it will be my pleasure to help - David@WheelsBoutique.com
Does anyone have any concave or deep dish wheels on their Z06? If so, what do you have and can you provide some pics? I'm having a SUPER hard time finding wheels that fit as no one seems to carry wheels in our bolt pattern and offset. I feel like there should be a whole forum subcategory about wheels since I see so many aftermarket ones all over the forum. At the very least there should be a sticky!
Klassen iD M52R
Deep Concave front & rear
Forgestar Deep Concave front & rear
Vorsteiner V-FF 103 Deep Concave
You would only be able to run Deep Concave Front & Rear for the most part.
I have done a couple super deep concave profiles in the rear, but the fitment is aggressive.
Example: Regular fitment for the rear 20x12+46mm
Aggressive fitment Super Deep Concave 20x12+32
The rear will poke 14mm more outwards.
My customer over in AUS did have coilovers and was able to adjust the camber correctly but it sill had 5mm poke.
Let me know, we carry HRE, Brixton, ADV.1, Forgeline, Klassen, Forgestar, 360 forged, BC Forged. .
The fitment for all of the manufactures would be about the same.
here are a couple links to our threads brother, let me know if you have any questions. forum@vibemotorsports.com | 1-800-814-8423 x104
Thanks all for the inputs. I'm not sure why almost every aftermarket wheel I see for the C7s has very thin spokes. I prefer the slightly thicker spokes. Something like this
That's a Ferrada FR1 and when I talked to the guy at the place that sold these, 1) this was for a stingray, and 2) it didn't quite fit right anyway (slightly off bolt pattern) but they "made it ft" and I don't really want to do that. I'm still looking though
Much to the point of what's been said above, the Chevrolet Corvette has notoriously high wheel offsets. The higher the offset, the less concave a wheel will be. In addition to that, if you want the deepest dish possible the center of the wheel has to be flat. The more concave you make the center face of a 3-piece wheel the more it robs you from the amount of dish you get.
Over the years we have help set up hundreds of Corvette's and our gallery can be seen here - https://wheelsboutique.com/gallery/chevrolet/pics/chevrolet-corvette. We focus on premium custom forged wheels built here in the U.S. An American legend like the Corvette deserves wheels built here. If you'd like more information & explanation on what's possible with your Corvette send me over a quick email and it will be my pleasure to help - David@WheelsBoutique.com
Honestly I'd PREFER a deep dish with a flat face, but I'd settle for a deep concave. Now that's on the rear. I want the fronts to be basically flush. Maybe a very small lip or slightly concave.
11-08-2018, 01:55 PM
Concave/deep dish wheels
