Magnuson 2650
06-08-2019, 09:56 PM
#1
Instructor
Thread Starter
Magnuson 2650
Anyone have this on their beast yet? Looking to see some videos....
I ordered two.... One for my Trackhawk... and one for my z06... Look forward to sharing with you guys the outcomes!
I ordered two.... One for my Trackhawk... and one for my z06... Look forward to sharing with you guys the outcomes!
06-08-2019, 11:26 PM
#2
Supporting Vendor
we install the one here on the 18th.
__________________
Cordes Performance Racing aka "CPR"
Owner of AZ's premier LSX/LTX motorsports shop
http://cordesperformanceracing.com/
www.facebook.com/cordesperformanceracing.com
joe@cordesperformanceracing.com
480-359-5914
Cordes Performance Racing aka "CPR"
Owner of AZ's premier LSX/LTX motorsports shop
http://cordesperformanceracing.com/
www.facebook.com/cordesperformanceracing.com
joe@cordesperformanceracing.com
480-359-5914
06-08-2019, 11:31 PM
#3
Instructor
Thread Starter
06-09-2019, 12:20 AM
#5
Supporting Vendor
Facebook Post
should
The following users liked this post:
bbbvettes.com (06-16-2019)
06-09-2019, 03:06 AM
#6
not sure yet. however the lt5 sure does, 2300, and oem blower with our 5'' cold air intake
https://www.facebook.com/Cordesperfo...2111376384188/
should
https://www.facebook.com/Cordesperfo...2111376384188/
should
The following users liked this post:
Cordes Performance Racing (06-09-2019)
06-09-2019, 08:09 PM
#8
Race Director
My buddy is stock cam and heads just 2300 and a pulley. He is out of fuel at this point. I would imagine out the box you would need to upgrade the fuel system which is a pita in these cars compared to old gens.
06-09-2019, 09:13 PM
#9
Supporting Vendor
06-11-2019, 08:17 AM
#10
Supporting Vendor
😁 This thing is massive. It's 3" wider than a heartbeat 2300. Will require valve covers for sure so budget for that.
The following users liked this post:
chevyfanatic (09-06-2019)
06-11-2019, 09:02 AM
#12
Supporting Vendor
06-11-2019, 09:13 AM
#14
Supporting Vendor
Magnuson 2300, our 5" cold air intake, our heads/cam package, 103 mm throttle body, upper/lower, bolt on's, our fuel system, e85, meth, our expansion tank/ice tank, our heat exchanger. Car made 830 in 90 degree weather.
Last edited by Cordes Performance Racing; 06-11-2019 at 09:14 AM.
06-11-2019, 09:46 AM
#16
Supporting Vendor
$1000 more. They don't come with pulleys though so add $80 there. Also factor in valve covers so $500 for some moroso's (least expensive offering) than you need a welder to add pcv fittings onto the covers and hardware to mount coils.
The following users liked this post:
Shostopper (06-11-2019)
06-11-2019, 09:52 AM
#17
Melting Slicks
Any ability to run port injection or is that basically out due to the size of the blower?
06-11-2019, 09:56 AM
#18
Supporting Vendor
If you could you'd have to hang the injectors off the side at a terrible angle which I absolutely do not like. And than things get even more jam packed with rails, fittings, line, etc.
The following users liked this post:
chevyfanatic (09-06-2019)
06-11-2019, 09:58 AM
#19
Burning Brakes
Thanks I still plan on having you guys build my car when I get the funds.
The following users liked this post:
Cordes Performance Racing (06-11-2019)
06-11-2019, 10:04 AM
#20
Supporting Vendor
