CorvetteForum - Chevrolet Corvette Forum Discussion - View Profile: Anthony @ LGMotorsports

Go Back  CorvetteForum - Chevrolet Corvette Forum Discussion > Members List
Reload this Page >

Anthony @ LGMotorsports's Profile


0Anthony @ LGMotorsports Anthony @ LGMotorsports is offline

Former Vendor

Visitor Messages

Showing Visitor Messages 1 to 10 of 47
  1. C6z_racing
    07-13-2017 03:23 PM

    I bought some G2 coil overs from you last year for a C6Z race car, can you send me the setup specs again? Castor, camber, and toe?

  2. FlipRay
    11-26-2016 07:01 PM
    Anthony, got a quick question for you guys. Whats typically the spring rate for your LG GT2s for C6Z? I bought a set from you guys about a year ago and cant find any spec for spring rates anywhere. Do you guys do revalve jobs if I wanted to go stiffer springs? Thanks, just shoot me a PM back when you can.
  3. Boba Fett
    10-02-2016 08:01 PM
    Please pm a price for a set of the G2 coil overs for an 07 Z06. Buddy from Fla said you'll do the best price Thanks. Shipped to 12538
  4. C6C3Vettes
    08-02-2016 10:01 PM
    Anthony - have you mailed the rubber bumpers for my hood?

    Kevin Kohlscheen

    The corner of my CF hood nearest the windshield on the drivers side sticks up higher than the fender? Any ideas on how to adjust it? There are also a couple of cloudy spots that appear to be in the clear coat. Any ideas on that?


    Kevin Kohlscheen[/QUOTE]

    Make sure you use some kind of wax or polish with a uv protectant...I think Zanio does and other similar products do as well.

    for the corner....the carbon, or real carbon, per say will move around a bit and can change with this something that moves a bit with heat? Wonder if it did it while it was outside here? At any rant on some of the cars I have had to run a small rubber "bumper" so to speak about half way up the fender to cause the hood to bow a little bit to match the fender line which would typically bring that down...if I am right it is probably a little flat about half way up the fender?
  5. Rsharpatx
    05-26-2016 08:54 AM
    What would the price be with the quite endlinks?
  6. tbrent
    03-11-2016 12:09 PM
    Testin testing... Anthony are you okay?
  7. srm077
    02-25-2016 03:04 PM
    Do you have any of take off stock c6 z06 fascias lying around at the shop? My wife took mine out on a curb parking.
  8. SpartanSupps
    01-28-2016 08:43 PM
    Hello Anthony, I installed a LG cam and I needed the specs on it for a new head setup.
    The cam G7X5
    If you could pm or email those specs I would greatly appreciate it!
    email: [email protected]
    Thank you sir
    10-30-2014 09:47 PM
    Anthony can you please send me a PDF file for the instructions on the G2 coilover installation. I purchased from TPS and I did not receive anything with instructions. I;m having a nightmare of a time installing the rear coilovers and I'm a bit confused on how exactly they bolt up to the upper frame on a C5. It seems as if the coil spring will hit the axle shaft boot and rear tie rod. The bracket is offset and I just really need some good pictures if you have them to properly show me how to do it. You can PM me or my email is revha[email protected]

    thank you so much
  10. keith954
    04-09-2014 09:01 PM
    Clear out your inbox

About Me

  • About Anthony @ LGMotorsports
    Full Name
    Anthony Forney
    Lewisville TX
    Your Zip Code
    Country of Residence


Total Posts
Visitor Messages
Total Thanks
General Information
  • Last Activity: 10-13-2017 06:21 PM
  • Member Since: 08-16-2005


Showing Friends 1 to 10 of 60

Social Profiles

Instant Messaging
Send an Instant Message to Anthony @ LGMotorsports Using...
Home Page
This Page
Sponsored Ads
Vendor Directory

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

© 2018 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to and affiliated sites.