CorvetteForum - Chevrolet Corvette Forum Discussion - View Profile: vettenuts


vettenuts vettenuts is offline

CF Senior Member

Visitor Messages

Showing Visitor Messages 1 to 8 of 8
  1. vettenuts
    10-19-2011 05:18 AM
    vettenuts
    I have the housing and the M8-1.25 and 3/8-24 collets. However, "Cross" contacted me first about the tools so I need to hear back from him if he still wants them. These are absolutely the best stud tools I have ever used and they don't damage the threads at all.
  2. 08 ATOMIC-Z
    10-18-2011 10:01 PM
    08 ATOMIC-Z
    Which collett's do you have. I have the snap-on tool but only the collett for the CRANE studs. If you want to sell these let me know.
  3. vettenuts
    01-12-2010 12:27 PM
    vettenuts
    Depends on the year. Later years were pretty much identical except for the obvious cam and heads.
  4. deadcafe
    01-12-2010 10:22 AM
    deadcafe
    Hey brother I have a question for you concerning 2 engine's. I am in a constant battle with a great friend of mine about the LS1 VS the LS6. were these 2 engines built with the same bolt on parts to their stock short block would the LS6 short block see higher HP/TQ numbers? I told him they are the same block and it is like compairing a 2 bolt main 5.7 to a 4 bolt main 5.7. What are your thoughts
  5. vettenuts
    09-12-2008 11:50 AM
    vettenuts
    Here it is (I'm home today). I cut the end of of a socket and had it welded to a flat bar. Pretty simple if you know someone who welds and it will come in hand later too.




  6. T.J.
    09-12-2008 08:15 AM
    T.J.
    I'll find it.
    Thanks
  7. vettenuts
    09-11-2008 12:04 PM
    vettenuts
    You need to do this with the plugs out. I made a tool to do this, it is comprised of a socket (cut in half) welded to a 1/8" flat bar. I have posted photos of it before if you can find it with search. I can't get at it now due to being at work.
  8. T.J.
    09-11-2008 01:11 AM
    T.J.
    Vettenuts, I'm almost finished with the head install. I've been following the directions from ls1howto, but after placing the YT's on they reccomend to turn the motor by hand. I didn't remove the powersteering rack since doing heads only, so do I still need to turn the motor over by hand? I don't remember reading anything in the shop manual about needing to turn it over by hand to build up compression. Once again just checking before I mess up. Thanks for all of your advice.
    T.J.

About Me

  • About vettenuts
    City
    At the beach
    State
    in little Rhody
    Your Zip Code
    02879
    Occupation
    Mechanical Engineer - Structural Dynamics
    Year & Model
    2002 Convertible
    Color
    Mag Red
    Country of Residence
    US
  • Signature
    New England Captain - National Corvette Caravan 2003


    02 Mag Red Vette Convertible
    Callaway Honker CAI, ATI Balancer, Cloyes IRL chain, GMPP dampener, AFR 205's, AFR 6016 cam, YT Rockers, QTP Headers, Morel lifters, DeWitts, Textralia X-Grip & DTE Stage IV 3.90's.

Statistics

Total Posts
Visitor Messages
Total Thanks
General Information
  • Last Activity: Today 08:21 AM
  • Member Since: 03-16-1999

Friends

Showing Friends 1 to 8 of 8

Social Profiles

Instant Messaging
Send an Instant Message to vettenuts Using...
Home Page
http://corvetteforum.net/c4/vettenuts/
This Page
https://www.corvetteforum.com/forums/members/563-vettenuts.html
Sponsored Ads
Vendor Directory

All times are GMT -4. The time now is 03:19 PM.