Input on Building Slot Car Track
#1
Melting Slicks
Thread Starter
Input on Building Slot Car Track
I just purchased a slot car set and am drawing up plans to build the table but wanted to solicit input from anyone who's previously done this - I'm open to suggestions. Once it's built, I plan on having a GTG at my house (mid to late June) and holding races for everyone who wants to participate.
The track is roughly 9.8' x 6.6' (just under 25 feet of total track) so I'm planning on building the table 10x8' since most sheets of 3/4" plywood come in 4x8' sheets. The base/frame will be made of 2x4" and I'm thinking of building the whole thing in two sections to make it easier to move; one 4x8' and 6x8' - see diagram below:
The track is roughly 9.8' x 6.6' (just under 25 feet of total track) so I'm planning on building the table 10x8' since most sheets of 3/4" plywood come in 4x8' sheets. The base/frame will be made of 2x4" and I'm thinking of building the whole thing in two sections to make it easier to move; one 4x8' and 6x8' - see diagram below:
#2
With support underneath you could use a pulley system to lift/lower it in the garage or wherever you are placing it.
I still have all of the sets that our family had from the 1/32nd scale in the early 60's through the HO scale tracks of the 70's. 1/32nd scale was a rubber track. The HO and 1/24th scale was a plastic textured surface.
Be sure when building it that all your track connects smoothly so the cars don't catch on each section, especially in the turns.
Test power to the track at several points to be sure you are getting even power throughout the track as well. If not, add wiring from the transformer/controller section to the opposite side to help things out. Don't get that criss-cross section wrong
The last HO car I purchased was probably in the early 80's. The 1/32nd scale cars were hand built with brass tubing and had plastic bodies similar to models.
Have fun!
I still have all of the sets that our family had from the 1/32nd scale in the early 60's through the HO scale tracks of the 70's. 1/32nd scale was a rubber track. The HO and 1/24th scale was a plastic textured surface.
Be sure when building it that all your track connects smoothly so the cars don't catch on each section, especially in the turns.
Test power to the track at several points to be sure you are getting even power throughout the track as well. If not, add wiring from the transformer/controller section to the opposite side to help things out. Don't get that criss-cross section wrong
The last HO car I purchased was probably in the early 80's. The 1/32nd scale cars were hand built with brass tubing and had plastic bodies similar to models.
Have fun!
#3
Le Mans Master
This looks like fun, Aaron. At my age I fear I've lost both reaction time and eyesight. I to think 1:32-scale is the way to go, mostly for the variety of cars it provides. Lots of Corvettes. And other things as well.
Wonder if they make scale hay trucks so I can at least beat Poodle Girl when we compete. At least I can scare the bejeebers out of him.
Maybe you could build a to-scale replica of the XXX parking lot complete with little lawn chairs and a vineyard for those who prefer sour grapes. It might really be fun to find one of those ancient electric football games and paint up the players to look like participants while they run around in circles while awaiting their turns on the track.
I am considering building a replica of the C6 Aero Lightweight (one of 42) but I worry that it would be too light to stay in its own slot. Based on my experience with the hobby however, I will volunteer to be a corner worker.
Call me if you need any help. Have you seen the track at the LeMay Museum in Tacoma?
Wonder if they make scale hay trucks so I can at least beat Poodle Girl when we compete. At least I can scare the bejeebers out of him.
Maybe you could build a to-scale replica of the XXX parking lot complete with little lawn chairs and a vineyard for those who prefer sour grapes. It might really be fun to find one of those ancient electric football games and paint up the players to look like participants while they run around in circles while awaiting their turns on the track.
I am considering building a replica of the C6 Aero Lightweight (one of 42) but I worry that it would be too light to stay in its own slot. Based on my experience with the hobby however, I will volunteer to be a corner worker.
Call me if you need any help. Have you seen the track at the LeMay Museum in Tacoma?
#4
Melting Slicks
Thread Starter
Thanks for the replies. I like the idea of a pulley system - my shop has high ceilings with exposed beams so that is definitely feasible.
#5
Burning Brakes
That is very cool. Consider finding a used ping-pong table on CL as the base. Securing thinner than 3/4" plywood to the table could improve the portability.
#6
Melting Slicks
Thread Starter
I'd read about people using a ping pong table but it's smaller overall than the track I believe. I'll look into it some more. I'd originally thought about 3/4" plywood before I decided I needed a frame instead since I can't find one sheet of plywood measuring 10'x8'.
#7
Safety Car
Aaron, I have a fully loaded woodworking shop with planer, jointer, tablesaw, band saws (2) and more. if you need any work done let me know.
Last edited by fperra; 04-30-2016 at 09:51 PM.
#8
Le Mans Master
Member Since: Oct 2004
Location: Everett WA
Posts: 7,690
Received 476 Likes
on
353 Posts
C4 of Year Finalist (appearance mods) 2019
Do keep in mind that just like a train track ..... you can always buy a few extra pieces of track and .. you know .... make it bigger or at least plan for that in your construction design.
#9
Melting Slicks
Thread Starter
I figure I'd better start with what I have and see how that goes - how much fun it is, how many people I can get involved in tournaments, etc.
#10
Melting Slicks
We have a Carrera set we put up around the Tree every Christmas. I still have my HO cars from the late 60's, had a *** 1/32nd Cheetah when I was a kid, no idea what happened to it...You should get more track and make an epic road course.....
Last edited by JETninja; 05-04-2016 at 12:29 AM.
#11
Melting Slicks
Thread Starter
Thanks for the push - I've been trying to be "reasonable." Even before I ordered it, I was looking at all the various real-world track configurations & plans Carrera offers. It would be really easy to go overboard - but then again, if I can get the whole track on a pulley system to raise it to the rafters when not in use, bigger wouldn't be a bad thing.
#12
If you do a bigger one the limit may be your ability to reach the center of the track to make repairs (cars falling off the track). Cut a hole in the middle. Measure twice, cut once!
The other issue with suspended tracks is getting them solid while in the down position.
The other issue with suspended tracks is getting them solid while in the down position.
#13
Le Mans Master
If you do a bigger one the limit may be your ability to reach the center of the track to make repairs (cars falling off the track). Cut a hole in the middle. Measure twice, cut once!
The other issue with suspended tracks is getting them solid while in the down position.
The other issue with suspended tracks is getting them solid while in the down position.
#14
Melting Slicks
Thread Starter
If you do a bigger one the limit may be your ability to reach the center of the track to make repairs (cars falling off the track). Cut a hole in the middle. Measure twice, cut once!
The other issue with suspended tracks is getting them solid while in the down position.
The other issue with suspended tracks is getting them solid while in the down position.
#15
Melting Slicks
Riverside International Raceway comes to mind. Used to have pics of a slot car track of it, maybe on my Desk PC....I'll look sometime soon. But it had everything, long straights, banked turn, fast corners and some slow ones, and elevation changes.....
#16
Le Mans Master
Good idea, John. I've driven that track (okay not very quickly) . Aaron could save a (small) fortune on scenery, like trees.
#17
Melting Slicks
Thread Starter
That was an interesting track layout and would probably be quite fun with slot cars. It's not one of the plans Carrera has though but worth investigating.
#18
Melting Slicks
I grew up at that track so it's always been one of my favorites. In the 60's and early 70s my folks brought me to everything there, Can-Am, Trans-Am, Nascar, F5000, etc. Then I was driving myself there and went for everything including all the bike racing and sports cars. Got to drive it a number of times, and used to have access to huge lenses so I used to just step over the fence and get great shots. I was there for the very last event, an SCCA runoff on a shorten version of the track, and in the evening we all did a lap and officially closed it forever. My first son was in the back set as few month old baby. (prob why he has the huge racing bug as an adult!)
#19
Burning Brakes
I remember the track as well. In 1976 I had just picked up a Pantera in Long Beach and went to Riverside to watch the NASCAR Riverside 400 which was won by David Pearson. I ended up with one of my worst sunburns but it was a great race.
#20
Melting Slicks
In 1970 or so, I was 11yrs old and under the turn 6 grandstand, Richard Petty had flatted, so in his effort to catch up he'd just kiss the wall in front of me lap after lap, it was very cool watching his control of that Dodge.....