Getting closer (Wheels are back from powdercoating, reflectors blacked out)
My wheels just got back from Mike' (Corvette Pilot on this forum) powdercoating service and I wanted to share with you what a GREAT DEAL having work done by him is. I was familiar with his service since he did my brake calipers a year ago (see picture below), but what I didn't expect was that having him powdercoat my wheels was actually cheaper than getting it done anywhere local here in NJ/PA/NY, despite the shipping.
I asked Mike for a glossy black that matches my car's factory color. These are stock Front C6 factory rims, and 2 of them have been widened by Weldcraft Wheels in Michigan to 18 x 11": http://i529.photobucket.com/albums/d...s/DSCF2382.jpg http://i529.photobucket.com/albums/d...s/DSCF2383.jpg http://i529.photobucket.com/albums/d...s/DSCF2381.jpg I will be running these tires in the wide rims: 305 35 18 http://www.powerlabs.org/images/c6/abitires.jpg The black wheels will match my black C6 with smoked lights and reflectors: http://i529.photobucket.com/albums/d...s/DSCF2380.jpg http://i529.photobucket.com/albums/d...s/DSCF2376.jpg So now I've got the rear tires, all 4 rims, and tire pressure sensors; I still need the front tires, and I am putting C6 logos on the center caps. I am also planning on a thin red lip around the edge of the wheels, matching the brake calipers, and also 2 red decals on the sides of the hood, to break up the black a bit... What do you think? Keep the wheels all black, or have the thin red lip painted around the edge? |
If it were me I'd keep them all black. Should be a nice setup when done! Agressive but still the sleeper look for the untrained eye!
|
Personally I think all black wheels look like wheels missing hubcaps. I think you need something to break it up a bit. Perhaps the C6 flag for the center caps will be enough. See how that looks first and then decide on the stripe.
A trick I did was to paint the rotor hubs a bright silver/chrome color. They match the color of the rotor face and they make the black wheels stand out more now. I'll get pics tomorrow. |
:thumbs: Looks great brother! Post pics asap!
CYA |
cool, looks nice.. btw, someone is sittin' in your tires..... :D
|
I have a similar setup as you do. Blacked out lights etc. and Im actually going to leave the lip chrome to break up the black and still keep a little shine in the car. As far as decals on the hood leave the stuff off. It looks so much better all sleak.
|
Originally Posted by c6 batmobile
(Post 1569237470)
I have a similar setup as you do. Blacked out lights etc. and Im actually going to leave the lip chrome to break up the black and still keep a little shine in the car. As far as decals on the hood leave the stuff off. It looks so much better all sleak.
http://www.vettestripes.com/new%20pi...S2/c6hs2_9.jpg I figured it'd be a good idea for the car show and since it is just $30 worth of Vynil I can always power wash them off afterwards if I get tired of the look :) I also got the fender stripes, for both fenders, but have not decided if I want to run them or not.. What do you guys think? http://www.vettestripes.com/new%20pi...nder/c6fd3.jpg |
For Me, visually, its hard to accept a totally one color anything...So I vote thin lip on the wheels, otherwise the whole area of the wheel is all hollow looking, and either one or the other on the stripes.
|
Do you have any closeups of how the weld looks from the inside after the powdercoating?
Steve |
Originally Posted by skamp
(Post 1569240667)
Do you have any closeups of how the weld looks from the inside after the powdercoating?
Steve It is pretty discrete. You'd have to know what you were looking for to spot that once the wheels have tires on them and they are mounted on the car since the welds are behind the brake rotors and painted over... |
All black.. :thumbs:
|
I like black wheels on a black car if the offset and stance is right. However, they can lack definition without a stripe to set them off from the rest of the car so I vote black with a red stripe.
|
Badass car, Sam!
|
All BLACK :thumbs:
The calipers red will be just enough to set it off. |
Skip the red stripes on the wheels and on the fenders. I like Corvette flags idea for the hubcaps.
|
I just got my wheels powdercoated locally. I think they look like crap...I wish I had gone with Mike instead. They are gloss black, I also got my calipers powdercoated red. I will post pics later when I get the car back together. I also painted my rotors bright silver.
|
BTW, I like the fender stripes. No stripes on the wheels though.
|
Originally Posted by bad2000z
(Post 1569245492)
I just got my wheels powdercoated locally. I think they look like crap...I wish I had gone with Mike instead. They are gloss black, I also got my calipers powdercoated red. I will post pics later when I get the car back together. I also painted my rotors bright silver.
|
Love the finish on the wheels, but you're right they lack something!!!!
I just bought a set of 18 from Aintqk(rj) to widen, can you pm me with the details and cost??:thumbs: |
http://i242.photobucket.com/albums/f...z/IMG_1034.jpg
http://i242.photobucket.com/albums/f...z/IMG_1033.jpg http://i242.photobucket.com/albums/f...z/IMG_1037.jpg Hopefully I'll have pics later after I get everything together. |
All times are GMT -4. The time now is 08:05 PM. |
© 2024 MH Sub I, LLC dba Internet Brands