Big boost build (pic heavy)
 

Figured I would start a thread up since my big build is coming up to the finish line finally. Backstory of the car was a 441ci stroker 13.1 CR setup. Made good power but I was wanting something more. I started the teardown and found a buyer for the motor in the car. Gave me a head start on everything else I was going to need in the future. This is my first big boost build and between this forum and alot of local friends (Unreal) I have been able to get it all together.
Basic rundown on the setup:
LSX Block 429CI
4.0 Stroke X 4.130 Bore
Callies Dragonslayer Crank
Callies I-Beam Rods
Wiseco -18cc Pistons
Cam Motion custom grind camshaft

Basically the rundown on the shortblock now to the long block.
Texas Speed 285cc 6 Bolt heads 70CC
Ti Intake valves, Iconnel exhaust valves
PAC 1207X Springs
Smith Bros 3/8 .135 wall pushrods
LS7 Intake manifold/90MM TB.

To get it all to the ground went with a Monster LT1-S Triple disc clutch.

Fuel System went with Fore Innovations Triple pump setup -10 feed -8 return
Be on E-85 most of its life
Bosch 210 Injectors

Supercharger setup
A&A Corvette YSI-B Head unit
A&A Direct Drive
IW 10% O.D. Balancer
10 Rib upgrade to try and eliminate as much belt slip as possible.

Exhaust
ARH 1 7/8 LT
Catless X Pipe
LG GT4 Axle Back

That's the basic rundown of the car. Will attach pictures of it along the way and how it sits now. Thanks for reading!
https://cimg8.ibsrv.net/gimg/www.cor...2b430220b9.jpg
https://cimg0.ibsrv.net/gimg/www.cor...6bd7bf75db.jpg
https://cimg2.ibsrv.net/gimg/www.cor...fc09e0310a.jpg
https://cimg3.ibsrv.net/gimg/www.cor...abd8744b33.jpg
https://cimg4.ibsrv.net/gimg/www.cor...62fa7b160.jpeg
https://cimg6.ibsrv.net/gimg/www.cor...bb0cf67149.jpg
https://cimg8.ibsrv.net/gimg/www.cor...c577e48a9f.jpg
https://cimg0.ibsrv.net/gimg/www.cor...a50e86b946.jpg
https://cimg2.ibsrv.net/gimg/www.cor...5d52f6cae8.jpg
https://cimg3.ibsrv.net/gimg/www.cor...4b487738d2.jpg
https://cimg4.ibsrv.net/gimg/www.cor...3ced1fb76c.jpg
https://cimg7.ibsrv.net/gimg/www.cor...7779ca21d8.jpg
https://cimg8.ibsrv.net/gimg/www.cor...72d403dcb1.jpg
https://cimg9.ibsrv.net/gimg/www.cor...a8d73ab072.jpg
First wash in over a year. Was filthy
https://cimg0.ibsrv.net/gimg/www.cor...073dda4fb9.jpg
Heading to the shop for the fuel system

In for results.

What shop is doing fuel system and tuning?

It's gonna be a beast ! :cheers:

Excited for you... Watching the build! My F1-X build will be tuned soon hopefully!

You and me both man.
Modern Performance in Glendale. Chris tuned my last setup. Good dude
Thanks man been a long project for sure!
That's awesome, cars gonna be an animal!

Very cool, didn't realize there were competent tuners on our side of town, I'm at 67th / HV but use CPR. You must be like a kid at Christmas waiting for tune!

Yea they're off 67th and Northern. The anticipation is killing me!

I just dropped mine off Friday probably won't be done until 12th or 15th, trying to get the summer IATs down.

this engine look insane! Congrats.

I appreciate it ��

Very nice. What's your end goal? Are you going to overspin the blower?

I'll be satisfied with anything around 1000 in our current weather in AZ. Have a 2.70 head unit pulley and 10% OD at 7k should be around 72k rpm

:lurk:

So you must be the Yellow ZR! I've been seeing lately LOL
I'm also at 67th/HV :)

Nacho needs that spray installed !!!!!! LOL

Can't wait to see the finished product :)

:D Yeah, I live up by Deems actually where 51st and 55th intersect north of HV. Would love to see your build after it's finished.

Yea he needs to put it on already!!

Dang, What did a build like that cost if you don't mind me asking?

Stopped adding it up after 20k honestly