CorvetteForum - Chevrolet Corvette Forum Discussion - Search Results

Search: Posts Made By: Solid LT1
Showing results 1 to 17 of 17
Search took 0.03 seconds.
06-05-2017, 05:18 PM
Replies: 5
Views: 413
Posted By Solid LT1

Yes those cup washer go between the spider gears...

Yes those cup washer go between the spider gears and the posi case and will fall out when you least need them to....get the case in a position where you can get a washer in...align the spider gear...
03-01-2017, 11:57 PM
Replies: 5
Views: 796
Posted By Solid LT1

I have a Greenwood 5 link and Guldstrand cobbled...

I have a Greenwood 5 link and Guldstrand cobbled 6 link set up (work is pretty crude but, I was told it came off a car fabbed in Dicks shop)....if your interested I'm ready to clear some stuff out of...
09-08-2016, 01:46 PM
Replies: 7
Views: 2,023
Posted By Solid LT1

Pan takes normal Corvette pick up.....all small...

Pan takes normal Corvette pick up.....all small block pick ups for corvettes are the same.
Forum: C3 General
07-16-2016, 08:45 PM
Replies: 62
Views: 5,026
Posted By Solid LT1

Ken at Lonestar might be the largest rebuilder of...

Ken at Lonestar might be the largest rebuilder of Delco Moraine 4 piston calipers BUT......the original rebuilder who engineered and perfected the stainless steel re-sleeveing of Moraine calipers was...
05-30-2016, 09:06 PM
Replies: 19
Views: 2,707
Posted By Solid LT1

This IS the most MISERABLE! job to do of any on...

This IS the most MISERABLE! job to do of any on the C3 Vette in my opinion.....talking C-60 equipped C3 Vettes.....
05-13-2016, 12:17 AM
Replies: 1
Views: 482
Posted By Solid LT1

RH side is Passenger.....usually has the thickest...

RH side is Passenger.....usually has the thickest shim pack but not always.....the thickness of shims is dictated by gear pattern/backlash requirements.
05-04-2016, 01:57 PM
Replies: 8
Views: 871
Posted By Solid LT1

Smokey did tons of testing using a clear cover on...

Smokey did tons of testing using a clear cover on the SY-1 intake. They work like gangbusters in the RPM ranges they are tuned for.....out of the range.....NOT SO GOOD! I ended up modifying 2 NASCAR...
05-04-2016, 12:20 PM
Replies: 37
Views: 3,281
Posted By Solid LT1

You CANT put a Holley electric choke on a factory...

You CANT put a Holley electric choke on a factory Holley carb set up for a divorced choke. If the car the OP is working on is an LT-1 Vette, they should hunt up a factory intake and go from there.
Forum: C3 General
04-17-2016, 10:13 PM
Replies: 226
Views: 19,806
Posted By Solid LT1

My wife and I did the Grand Canyon, Bryce and...

My wife and I did the Grand Canyon, Bryce and Zion Canyon last year. If your in Springdale near Zion, I highly recommend breakfast at "The Spotted Dog" diner, make reservations because it's one of...
Forum: C3 General
03-24-2016, 03:02 PM
Replies: 125
Views: 11,848
Posted By Solid LT1

I think there should be an alliance between the...

I think there should be an alliance between the Corvette Museum and the NCRS. There should be a artifact library of club and GM documents yo support the restoration hobby. Most European manufacturers...
03-24-2016, 12:17 AM
Replies: 18
Views: 2,716
Posted By Solid LT1

I've built around 20 LT-1s/Z28 302 motors in my...

I've built around 20 LT-1s/Z28 302 motors in my life. I run my motors pretty hard, I don't use cheap parts in my builds, I'll use a $99 oil pump over a $47 one anytime if I think the part will add...
02-25-2016, 06:33 PM
Replies: 5
Views: 566
Posted By Solid LT1

BUY the harness from Wilcox....its Lectric...

BUY the harness from Wilcox....its Lectric Limited, they have better pricing on them than you could get by buying into Lectric Limited for a $5K dealer order. Thanks Wilcox!
02-17-2016, 12:50 AM
Replies: 42
Views: 3,177
Posted By Solid LT1

If your smart you'll not do too many aftermarket...

If your smart you'll not do too many aftermarket upgrades to a 72 LT-1 roadster. The factory F-41 type suspension upgrade I did on my 72 LT-1 coupe gave me an autocross championship not too many...
01-30-2016, 08:22 PM
Replies: 19
Views: 2,570
Posted By Solid LT1

I don't think highly of those Global West...

I don't think highly of those Global West bushings. I know they require welding the threaded "spud" in the lower control arm shaft, the lower shaft is a forging and I don't think highly of the...
Forum: C3 General
01-11-2016, 05:12 PM
Replies: 48
Views: 4,243
Posted By Solid LT1

I hope for your sake you have a reserve on your...

I hope for your sake you have a reserve on your LT-1! They don't seem to pull many $$ at BJ's....good luck with the sale:thumbs:
02-13-2013, 12:28 AM
Replies: 10
Views: 1,120
Posted By Solid LT1

I use Simple Green or Castrol Super Clean for...

I use Simple Green or Castrol Super Clean for this task. Just get a cheap plastic tarp protect your concrete floor and throw it away when done. I also have an "El Cheapo" hand held steam cleaner that...
Forum: C3 General
09-21-2012, 12:18 AM
Replies: 650
Views: 144,150
Posted By Solid LT1

MULSANNE BLUE! wife wanted LeMans Blue, I said...

MULSANNE BLUE! wife wanted LeMans Blue, I said NO! original color it is!

48145663

Looks better in full motion! Link: http://www.youtube.com/watch?v=Xg8UGPPsBsY
Showing results 1 to 17 of 17


 
Forum Jump

Sponsored Ads
Vendor Directory

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.