CorvetteForum - Chevrolet Corvette Forum Discussion - Search Results


Showing results 1 to 12 of 12
Search took 0.02 seconds.
Search: Posts Made By: 85 Stalker
Forum: C4 General Discussion 09-08-2017, 10:04 AM
Replies: 14
Views: 510
Posted By 85 Stalker
I'll need to find an older picture, mine were...

I'll need to find an older picture, mine were black and blue.
Forum: C4 General Discussion 09-08-2017, 07:25 AM
Replies: 14
Views: 510
Posted By 85 Stalker
I had them before I converted the interior, they...

I had them before I converted the interior, they are very nice covers that are well made.
Forum: C4 General Discussion 08-17-2017, 08:01 PM
Replies: 11
Views: 361
Posted By 85 Stalker
If you are planning to hide the light wires in...

If you are planning to hide the light wires in the support structure now would be a good time to drill the holes for routing (before you paint).

I used Krylon flat black on mine and it looks just...
Forum: C4 General Discussion 06-14-2017, 05:17 PM
Replies: 14
Views: 605
Posted By 85 Stalker
For years the only way I would drive the Vette is...

For years the only way I would drive the Vette is with the top off. But now that I'm on the downhill side of 50 I enjoy it with the top on, windows up and the AC on high.:steering:
Forum: C4 General Discussion 06-03-2017, 12:48 PM
Replies: 44
Views: 2,113
Posted By 85 Stalker
Twin turbo / meth Gen III HEMI in a 80 Aspen. ...

Twin turbo / meth Gen III HEMI in a 80 Aspen. The interior is from a 2015 SRT - everything is built from the ground up.

...
Forum: C4 General Discussion 06-02-2017, 06:05 PM
Replies: 11
Views: 695
Posted By 85 Stalker
Should move plenty of air focused directly to the...

Should move plenty of air focused directly to the spray bar and intercooler. If I need to open it up a little more that will be real easy to remove the center section and bridge it with an aluminum...
Forum: C4 General Discussion 05-27-2017, 03:23 PM
Replies: 11
Views: 695
Posted By 85 Stalker
I think this will flow well with the front end,...

I think this will flow well with the front end, it should be a clean look. If not, back to the drawing board:crazy:
Forum: C4 General Discussion 05-26-2017, 04:45 PM
Replies: 11
Views: 695
Posted By 85 Stalker
Just ordered the Duplicolor rattle can base/clear...

Just ordered the Duplicolor rattle can base/clear -- we'll see how close it is.............
Forum: C4 General Discussion 05-25-2017, 03:38 PM
Replies: 11
Views: 695
Posted By 85 Stalker
Making my own A/O Forced Air Inlet Plate

I've searched far and wide for an A/O Forced Air Inlet plate, that is one item that has become very scarce. With my car the plate opening is cut out for the intercooler and Co2 spray bar. For a...
Forum: C4 General Discussion 01-07-2017, 09:56 AM
Replies: 98
Views: 9,113
Posted By 85 Stalker
Another stock C4.... :-) ...

Another stock C4.... :-)


https://cimg0.ibsrv.net/gimg/www.corvetteforum.com-vbulletin/960x639/80-vette_at_quarry_3a92c0bc20e624759157d2c9a2834a584836d20c.jpg
...
Forum: C4 General Discussion 12-15-2016, 06:00 AM
Replies: 13
Views: 1,429
Posted By 85 Stalker
Two Kicker L5's ...

Two Kicker L5's

https://cimg2.ibsrv.net/gimg/www.corvetteforum.com-vbulletin/1632x1224/80-black_interior_c2c46060a07bedb0f00d8bd606f4a80b69c4098d.jpg
Forum: C4 General Discussion 11-04-2016, 01:24 PM
Replies: 44
Views: 2,303
Posted By 85 Stalker
We made a casting for my SR with an embedded C4...

We made a casting for my SR with an embedded C4 emblem. The casting was based off the original finned lid which does not have as many fasteners as yours.
...
Showing results 1 to 12 of 12

 
Forum Jump
Sponsored Ads
Vendor Directory

All times are GMT -4. The time now is 06:35 PM.