CorvetteForum - Chevrolet Corvette Forum Discussion - Search Results

Notices
Search: Posts Made By: Darinm
Showing results 1 to 16 of 16
Search took 0.21 seconds.
Forum: C3 General
03-20-2018, 08:22 AM
Replies: 8
Views: 314
Posted By Alan 71

Hi D, An award for your car, GREAT! Pretty...

Hi D,
An award for your car, GREAT!

Pretty nifty radiator hose!!!
Regards,
Alan
03-20-2018, 07:31 AM
Replies: 3
Views: 228
Posted By cooper9811

I have steeroids and the GM setup used on the...

I have steeroids and the GM setup used on the early 90s camaro/firebird. However, the Saginaw-style pump is the one used with this kit, and it also does not necessitate the conversion to a rack and...
Forum: C3 General
03-19-2018, 09:10 PM
Replies: 8
Views: 314
Posted By Vettedreamer74

The clear coolant hose is AWESOME!! Never seen it...

The clear coolant hose is AWESOME!! Never seen it before. Did you make it yourself? Car looks great and your engine bay looks fantastic! Do you have a crate in there?
Forum: C3 General
03-19-2018, 10:51 AM
Replies: 8
Views: 314
Posted By henrikse

Great job Nice car!

Great job Nice car!
10-27-2017, 12:13 PM
Replies: 10
Views: 262
Posted By MelWff

Just to be safe check the connections on the...

Just to be safe check the connections on the alternator. Make sure the large red wire connection is tight and unplug the two wire connector, look for any corrosion, and plug it back in.
Forum: C3 General
06-12-2017, 04:36 PM
Replies: 31
Views: 1,693
Posted By henrikse

If you look at pg 8a-43 and 44 at the choke relay...

If you look at pg 8a-43 and 44 at the choke relay circuit you will see there are 2 capacitors (c115 and c602. Check these to make sure they are not shorted. Can check them disconnected with ohmmeter....
Forum: C3 General
06-04-2017, 06:22 PM
Replies: 31
Views: 1,693
Posted By henrikse

First where is the water coming in that caused...

First where is the water coming in that caused corrosion? If you have fixed the water problem you have two choices? One would be to replace the fuse box and wiring from it to the connectors which...
Forum: C3 General
05-31-2017, 03:39 PM
Replies: 31
Views: 1,693
Posted By Willcox Corvette

The 79 schematic won't work for your car... but...

The 79 schematic won't work for your car... but just so people know, if you right click and copy that file, then paste it into your paint program it becomes a life size traceable schematic.
...
Forum: C3 General
05-31-2017, 10:37 AM
Replies: 31
Views: 1,693
Posted By Cooter Tech

Here is the entire page. Hope it helps

Here is the entire page. Hope it helps
Forum: C3 General
05-31-2017, 09:43 AM
Replies: 31
Views: 1,693
Posted By Cooter Tech

I know the misery of working under the dash, I...

I know the misery of working under the dash, I feel like a walrus trying to get out from under it. Is there any chance the radio is causing the voltage drop? Did you disconnect the connector in the...
Forum: C3 General
04-22-2017, 10:54 PM
Replies: 8
Views: 613
Posted By cagotzmann

I have the same wildwood calipers. YOU...

I have the same wildwood calipers.

YOU CANNOT BLEED the rear wildwood D8-4 calipers mounted on the car.

I removed the units placed a block between the pads to simulate the rotor width. Stood...
Forum: C3 General
04-22-2017, 04:46 PM
Replies: 8
Views: 613
Posted By henrikse

I've read they are hard to bleed and some take up...

I've read they are hard to bleed and some take up to 4 times to get a pedal. I would say to bleed them again. Are you using vacuum pump or somebody pumping the brakes?
I read an interesting article...
04-09-2017, 11:01 AM
Replies: 26
Views: 1,366
Posted By REELAV8R

Are these heads the 195 cc runners or the 185cc...

Are these heads the 195 cc runners or the 185cc runners?

Just about as important as flow in the heads is velocity. Too little velocity and you may suffer from sluggish bottom end and poor...
04-08-2017, 12:37 PM
Replies: 26
Views: 1,366
Posted By v2racing

I would run a cam with something in the mid 230's...

I would run a cam with something in the mid 230's @ .050" in a hydraulic roller. The exact numbers for split and lift would depend on the flow numbers from your heads. Did your engine builder give...
04-05-2017, 03:28 PM
Replies: 26
Views: 1,366
Posted By REELAV8R

Yes cylinder pressure is related to CR as well....

Yes cylinder pressure is related to CR as well. It is also related to the duration on the cam. The higher the duration on your cam then the later the intake valve closes to start compressing the...
12-01-2016, 12:13 PM
Replies: 12
Views: 1,976
Posted By resdoggie

Darinm, I have sidepipes and put a bung/plug in...

Darinm, I have sidepipes and put a bung/plug in each collector. The O2 sensor is at the 4 0'clock position which is not recommended, as you noted. However, I use the afr gauge only for tuning and...
Showing results 1 to 16 of 16


 
Forum Jump

Sponsored Ads
Vendor Directory