CorvetteForum - Chevrolet Corvette Forum Discussion - Search Results

Notices
 
Search: Posts Made By: Jebbysan
Showing results 1 to 25 of 195
Search took 0.17 seconds.
07-09-2018, 08:43 PM
Replies: 12
Views: 519
Posted By Jebbysan

Yep....except no green coolant.....water only,...

Yep....except no green coolant.....water only, filtered preferred or even distilled if you want to go through the hassle.....
Neutralize and then flush two or three times with water and it should...
07-09-2018, 08:14 PM
Replies: 7
Views: 280
Posted By Jebbysan

I like Dart heads....so my recommendation would...

I like Dart heads....so my recommendation would be a pair of Dart 180 Pro 1 Platinums (NOT the SHP).
Here is my cam recommendation.........
07-09-2018, 06:24 PM
Replies: 12
Views: 439
Posted By Jebbysan

They are out there......I scored a pair of Dart...

They are out there......I scored a pair of Dart 200cc Iron Eagles on E-Bay ironically from a Corvette shop for $500.....they needed nothing when they got to me but the I.D. locators that everyone...
07-09-2018, 05:49 PM
Replies: 12
Views: 519
Posted By Jebbysan

Wood Bleach as a Flush (Oxilic Acid) and Baking...

Wood Bleach as a Flush (Oxilic Acid) and Baking Soda as a neutralizer afterward. This use to be the ingredients of Prestones Two-Part flush some years ago after it was banned in 05'
The stuff works!...
07-09-2018, 05:45 PM
Replies: 10
Views: 285
Posted By Jebbysan

Leave the Fel-Pro gasket passages alone. I...

Leave the Fel-Pro gasket passages alone. I suggest you find a copy of the performance gasket catalogue and read it. There are about 25 different head gaskets for SBC. The performance catalogue...
07-09-2018, 03:18 PM
Replies: 38
Views: 866
Posted By Jebbysan

I think you are running lean......the A/F should...

I think you are running lean......the A/F should be 12.0 or so under WOT for max power........the 770 Street Avenger runs notoriously lean out of the box.
If that A/F is correct on the Dyno...
06-17-2018, 11:26 AM
Replies: 17
Views: 595
Posted By Jebbysan

I recommend the Dart Pro1 180cc Platinums. Best...

I recommend the Dart Pro1 180cc Platinums. Best bang for the buck out of the box IMHO. Stay away from the SHP as it does not have the wet flow tech or the finish work the Pro1 has........
AFR stuff...
Forum: C3 General
05-22-2018, 09:10 AM
Replies: 99
Views: 10,292
Posted By Jebbysan

Glad to help.....nothing exotic, just straight up...

Glad to help.....nothing exotic, just straight up basic stuff and attention to detail.....
I still have the X-Pipe and still have not installed it!
Someday....life is demanding right now ;)

Jebby
05-20-2018, 07:33 PM
Replies: 5
Views: 299
Posted By Jebbysan

I had the MSD tach drive and 6AL in my 66'...

I had the MSD tach drive and 6AL in my 66' 327/350 and loved it. Curved perfectly....and fired instantly.

I run a Mallory Opti-Spark and 6AL in the 72' 406.....and this is a great system as...
04-04-2018, 07:38 PM
Replies: 45
Views: 1,313
Posted By Jebbysan

Initial timing on a fairly stock engine is not...

Initial timing on a fairly stock engine is not too critical as long as it is somewhere around 12-16.......mild small blocks seem to like 14.......
It is more important to set the total and see where...
03-26-2018, 01:18 PM
Replies: 40
Views: 1,331
Posted By Jebbysan

Remove the negative bat cable and run a test...

Remove the negative bat cable and run a test light in series. One end on the cable and one end on the post itself. If there is a draw.....the light will come on.
From there....start pulling fuses in...
03-26-2018, 09:16 AM
Replies: 11
Views: 424
Posted By Jebbysan

Good show.....SBC and BBC oil the cam first! ...

Good show.....SBC and BBC oil the cam first!

Jebby
03-25-2018, 02:45 PM
Replies: 11
Views: 424
Posted By Jebbysan

Word of advice....cam bearings go in with a...

Word of advice....cam bearings go in with a specific order.....this order is usually print on the box flap when you open it. BUT.....make sure somebody did not mixed up the bearing in the box. Look...
03-25-2018, 01:21 PM
Replies: 11
Views: 424
Posted By Jebbysan

I would replace them. Jebby

I would replace them.

Jebby
03-21-2018, 08:26 AM
Replies: 39
Views: 1,231
Posted By Jebbysan

Annular vs. Downleg has zero to do with vacuum at...

Annular vs. Downleg has zero to do with vacuum at WOT if the carbs for both types are properly sized for the application.
Generally I have watched most annular stuff go pig fat past the power peak...
03-20-2018, 07:42 AM
Replies: 23
Views: 751
Posted By Jebbysan

48265900 TCI rattler......they work.....but...

48265900

TCI rattler......they work.....but have not seen anyone run one for 15+ years.......been around since 97' or so......

Jebby
03-18-2018, 01:32 PM
Replies: 41
Views: 1,991
Posted By Jebbysan

I myself run a simple PCV setup with a Mr. Gasket...

I myself run a simple PCV setup with a Mr. Gasket chrome breather. The 406 only makes 10 inches of vacuum but the system works fine.
Since this photo....I have gotten rid of the line going to the...
03-18-2018, 12:04 PM
Replies: 23
Views: 751
Posted By Jebbysan

You are exactly right about a bigger balancer...

You are exactly right about a bigger balancer being able to snuff out harmonics better.....BUT.....on a pro balanced internal assembly....the smallest one available is really the choice.....Big...
03-18-2018, 11:28 AM
Replies: 13
Views: 457
Posted By Jebbysan

I have something to add.......I bought one...

I have something to add.......I bought one locally and although it works great it does not have the bleeders on the side above the brake line outlets.......I do not have a NCRS car, but I wish it...
03-15-2018, 08:15 PM
Replies: 24
Views: 896
Posted By Jebbysan

If the aluminum is in good shape on the...

If the aluminum is in good shape on the intake.....then no sealant is needed if it is FLAT.

Take the water neck and put a piece of 80 grit on a flat plate or granite stone to check and make the...
03-15-2018, 08:02 PM
Replies: 23
Views: 751
Posted By Jebbysan

Given that you are running high quality...

Given that you are running high quality parts....I recommend this unit and they are the best out there:

https://www.summitracing.com/parts/ati-917060/overview/

You simply cannot buy a better...
03-10-2018, 06:41 PM
Replies: 11
Views: 1,022
Posted By Jebbysan

PM sent. Jebby

PM sent.

Jebby
03-10-2018, 05:29 PM
Replies: 22
Views: 832
Posted By Jebbysan

As stated the Fed Mog kit is for open chamber...

As stated the Fed Mog kit is for open chamber heads........but as far as kits go.....that is a damn good one for a meat and potatoes street build......
Here is the one I would get:
...
03-10-2018, 05:10 PM
Replies: 20
Views: 683
Posted By Jebbysan

I recommend the HP series 830cfm unit. The HP...

I recommend the HP series 830cfm unit. The HP series is and always has been a rock solid performer.......I have one on my own car.....it took very little to make it just right. Anyone who has ever...
03-01-2018, 01:47 PM
Replies: 12
Views: 816
Posted By Jebbysan

What a spectacular deal.....I have this setup on...

What a spectacular deal.....I have this setup on my 72' and it rides and handles terrific.......as far as ride height, the front is adjustable....I don't think you could get a better stance:

Jebby
Showing results 1 to 25 of 195
 


 
Forum Jump

Sponsored Ads
Vendor Directory

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.