CorvetteForum - Chevrolet Corvette Forum Discussion - Search Results


Showing results 1 to 14 of 14
Search took 0.15 seconds.
Search: Posts Made By: terry82
Forum: C3 Tech/Performance 09-10-2017, 06:17 PM
Replies: 18
Views: 644
Posted By Dynra Rockets
OEM 81-82 have the tubes up high OEM 84-91 have...

OEM 81-82 have the tubes up high
OEM 84-91 have the tubes down low.

If you have an automatic you can use either. If you have a stock manual with Z bar then you cannot use the C4 on the drivers...
Forum: C3 Tech/Performance 08-15-2017, 07:06 PM
Replies: 15
Views: 343
Posted By REELAV8R
small metal box attatched to the firewall just...

small metal box attatched to the firewall just above and to the right (as you are facing rear of car) of your blower motor. Should have a couple of plugs into it. Look to see if they are melted or...
Forum: C3 Tech/Performance 08-15-2017, 05:21 PM
Replies: 15
Views: 343
Posted By REELAV8R
I'd look at the fan connections, The fan relay...

I'd look at the fan connections, The fan relay contactor ( for wear and corrosion) and the size of ground wire you used with the fan. Any one of these can cause a high amperage draw. Should have a...
Forum: C3 General 07-14-2017, 05:45 PM
Replies: 39
Views: 1,846
Posted By Dynra Rockets
They are 407 stainless. (ie, low nickle and...

They are 407 stainless. (ie, low nickle and chromium content, mostly mild steel). That means you can weld on it with standard rod you would use for mild steel without issue.

I did mine myself...
Forum: C3 Tech/Performance 07-10-2017, 10:20 AM
Replies: 65
Views: 2,893
Posted By Street Rat
That's when you send the little people in. Wives...

That's when you send the little people in. Wives and kids come to mind.
:D
Forum: C3 General 07-05-2017, 08:37 PM
Replies: 5
Views: 154
Posted By Big2Bird
90% sure it's 15/16" socket. Not metric.

90% sure it's 15/16" socket. Not metric.
Forum: C3 General 06-29-2017, 09:49 AM
Replies: 6
Views: 243
dryer

first remove the rocker panel from the passenger side then 3 screws from the bottom for access panel and it is super easy:rock:
Forum: C3 Tech/Performance 05-20-2017, 04:05 PM
Replies: 2
Views: 261
Posted By Buccaneer
Some 82 CFI info from GM engineer

Just a couple pages from this book which is a good read for the CFI guys. Short, but somewhat informative from the engineering perspective. Got this from a friend at vettes and caddies this morning....
Forum: C3 General 05-19-2017, 11:12 AM
Replies: 39
Views: 1,846
Posted By garrettb
They didn't say, but I'm 99% certain they're...

They didn't say, but I'm 99% certain they're stainless.
Forum: C3 General 04-17-2017, 12:47 PM
Replies: 6
Views: 715
Posted By chstitans42
Forum: C3 General 11-05-2016, 11:41 PM
Replies: 2,711
Views: 182,815
Posted By Bergerboy
Experienced the dreaded "Bleeder Valve Snap-Off"...

Experienced the dreaded "Bleeder Valve Snap-Off" on my right front caliper.
Snapped off during a re-build, and left only less than 1/8" of threaded shaft exposed.
Any advice on how to extract the...
Forum: C3 Tech/Performance 08-20-2016, 06:26 PM
Replies: 20
Views: 1,839
Posted By Jebbysan
It was a 305ci. rated 165 stock.....RPO LO3 The...

It was a 305ci. rated 165 stock.....RPO LO3
The LG4 was a 4bbl....rated at 145......
The Camaro crossfire system was identical though.

You would need about 200 hp to run 15.5 in a 3rd gen Z-28....
Forum: C3 General 06-11-2016, 09:13 PM
Replies: 11
Views: 1,044
Posted By Paul L
I hope you can see my original post and pics....

I hope you can see my original post and pics. Believe me it has made a world of driving pleasure since I did that job several moons ago.
Forum: C3 General 03-11-2016, 11:49 AM
Replies: 15
Views: 632
Posted By MelWff
Vacuum

The hose collapses due to atmospheric pressure being greater than internal pressure. This will only occur during the cool down process when the system attempts to suck coolant back into the...
Showing results 1 to 14 of 14

 
Forum Jump
Sponsored Ads
Vendor Directory

All times are GMT -4. The time now is 05:12 PM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.