CorvetteForum - Chevrolet Corvette Forum Discussion - Search Results

 
Search: Posts Made By: sccaGT1racer
Showing results 1 to 25 of 50
Search took 0.03 seconds.
05-22-2019, 05:02 PM
Replies: 39
Views: 2,983
Posted By sccaGT1racer

From what I seen on the ls1. Its probably got a...

From what I seen on the ls1. Its probably got a broken piston. They like to break the ring land between the top and second ring. If you catch it soon enough it will clean up with a .005 overbore....
05-21-2019, 06:37 AM
Replies: 9
[Z06] Re wings
Views: 977
Posted By sccaGT1racer

https://fairclothcomposites.com/ If you want...

https://fairclothcomposites.com/ If you want aero that makes big downforce.
05-20-2019, 06:34 AM
Replies: 15
Views: 667
Posted By sccaGT1racer

They always did the sound readings just after the...

They always did the sound readings just after the uphill when I was racing there. I got shut down during a Scca race weekend for being over 105 db with boom tubes on my 640 hp busch north car. I...
05-15-2019, 05:55 AM
Replies: 12
Views: 703
Posted By sccaGT1racer

150 degrees is the oil temp that I wait for.

150 degrees is the oil temp that I wait for.
04-30-2019, 06:45 AM
Replies: 12
Views: 599
Posted By sccaGT1racer

Brake clean and air pressure is how I cleaned...

Brake clean and air pressure is how I cleaned mine. Completely disassemble the main tank because there are a lot of places where debris can get trapped.
04-11-2019, 06:15 AM
Replies: 5
Views: 491
Posted By sccaGT1racer

700 front and 650 rear will get you in the...

700 front and 650 rear will get you in the ballpark. swaybar sizes?
03-31-2019, 08:14 PM
Replies: 18
Views: 883
Posted By sccaGT1racer

You should have went with 315 hoosiers on the...

You should have went with 315 hoosiers on the front. The 33.3 mm strano front bar is a good match for the stock rear bar. It is what I run with the stock rear bar on my c6 z06. The eibach adjustable...
01-23-2019, 05:42 AM
Replies: 25
Views: 3,451
Posted By sccaGT1racer

Completely stock 22000 miles spun rod bearings...

Completely stock 22000 miles spun rod bearings due to connecting rods rubbing together.
01-17-2019, 03:05 PM
Replies: 13
Views: 697
Posted By sccaGT1racer

Joe Aquilante PHOENIX PERFORMANCE 610 482-0141 ...

Joe Aquilante PHOENIX PERFORMANCE 610 482-0141 Call JOE He will be able to answer that for sure. Im going to say the konis are not going to have a length issue.
01-17-2019, 02:01 PM
Replies: 13
Views: 697
Posted By sccaGT1racer

My suggestion would be Koni yellow sports ...

My suggestion would be Koni yellow sports 3013-1023 fronts 3013-1024 rears They will have plenty of control and a step up from the stock t-1s.
01-15-2019, 05:52 PM
Replies: 12
Views: 719
Posted By sccaGT1racer

Starting with your ride height where it needs to...

Starting with your ride height where it needs to be and sway bars disconnected. Put the car one scales and adjust the cross weights diagonally. As an example if you add 1 turn to the LF and RR you...
01-02-2019, 07:01 AM
Replies: 28
Views: 1,418
Posted By sccaGT1racer

Get the van steel or borg Delrin kits and do all...

Get the van steel or borg Delrin kits and do all 4 corners. They are proven.
10-20-2018, 06:33 AM
Replies: 54
Views: 4,183
Posted By sccaGT1racer

I cant wait for these cars to age and become...

I cant wait for these cars to age and become reasonable to buy. Awesome car.
09-08-2018, 07:22 AM
Replies: 4
Views: 647
Posted By sccaGT1racer

The max bore size on a ls3 is 4.070. If you go...

The max bore size on a ls3 is 4.070. If you go to a ls7 block the max bore is 4.130.
08-31-2018, 06:50 AM
Replies: 23
Views: 1,560
Posted By sccaGT1racer

My 20's would only make noise when hitting the...

My 20's would only make noise when hitting the brakes when not up to temp.
07-29-2018, 06:27 AM
Replies: 7
Views: 470
Posted By sccaGT1racer

Delrin bushing set from van steel, 35 mm van...

Delrin bushing set from van steel, 35 mm van steel front bar, 1 inch adjustable rear bar, 4 18x10.5 rims from bobs house of wheels, 4 315 hoosier a7s , koni shocks yellows, max rear negative camber...
07-16-2018, 05:42 AM
Replies: 19
Views: 898
Posted By sccaGT1racer

The 1243 code means the pump motor stalled/isn't...

The 1243 code means the pump motor stalled/isn't running. On a c5 corvette the front to rear bias control is in the abs module. When there are active codes there is no bias control.
06-29-2018, 10:17 AM
Replies: 7
Views: 741
Posted By sccaGT1racer

If you want it to still ride smooth keeps the...

If you want it to still ride smooth keeps the springs you have and go with big bars soft springs. Id say go with a 35 mm front bar and a adjustable 1 inch bar for the rear. Change the shocks and get...
06-25-2018, 05:59 AM
Replies: 101
Views: 8,033
Posted By sccaGT1racer

I would use a 3rd party for the valve spring...

I would use a 3rd party for the valve spring testing. If you read the entire thread Josh had clearance issues with rocker arms and push rods. When you pay a premium price you don't expect to be a...
05-31-2018, 02:04 PM
Replies: 7
Views: 478
Posted By sccaGT1racer

It may help but only if the vac pump can over...

It may help but only if the vac pump can over come the crankcase pressure. You may want to look into a daily or are dry sump system as you will be halfway there for cost. You could also do a #12 line...
05-25-2018, 05:39 AM
Replies: 24
Views: 1,664
Posted By sccaGT1racer

just get the additive in it and drive it. The...

just get the additive in it and drive it. The short time you drove it did no damage. Its just a drain and fill so the plates had lube on them just not enough friction modifier. Go do some figure 8's...
05-09-2018, 06:54 AM
Replies: 17
Views: 830
Posted By sccaGT1racer

18x11 front with a 315 and 18x13 rear with a 345....

18x11 front with a 315 and 18x13 rear with a 345. You need to choose a class first because that will direct your choices.
05-02-2018, 11:41 AM
Replies: 29
Views: 1,749
Posted By sccaGT1racer

The radio didn't make a difference if it was...

The radio didn't make a difference if it was plugged in or not. Its the interface that plugs in between the factory harness and the radio.
05-02-2018, 06:26 AM
Replies: 29
Views: 1,749
Posted By sccaGT1racer

Unplug the aftermarket radio interface. I had...

Unplug the aftermarket radio interface. I had three of them that kept the bus active and the modules would not go to sleep. The draw was 58 milliamps. I ended up returning the radio back to stock...
04-13-2018, 06:25 AM
Replies: 49
Views: 2,946
Posted By sccaGT1racer

It looks like a piece of valve guide. There is...

It looks like a piece of valve guide. There is not enough taper to be a keeper.
Showing results 1 to 25 of 50
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.