CorvetteForum - Chevrolet Corvette Forum Discussion - Search Results

Notices
 
Search: Posts Made By: WVZR-1
Showing results 1 to 25 of 500
Search took 0.65 seconds.
08-02-2018, 10:17 AM
Replies: 5
Views: 247
Posted By WVZR-1

I would think that the 'engine pad information'...

I would think that the 'engine pad information' would be sufficient to ID the engine aspect of the car you have.
08-01-2018, 08:24 PM
Replies: 2
Views: 177
Posted By WVZR-1

Does the SPID LABEL show the UJ6 option? If it...

Does the SPID LABEL show the UJ6 option? If it doesn't I believe it safe to assume the car doesn't have. Make sure SPID VIN matches the windshield VIN.

If the option is present then - does the 2...
08-01-2018, 11:25 AM
Replies: 9
Views: 385
Posted By WVZR-1

The only issue I've seen discussed with a reduced...

The only issue I've seen discussed with a reduced thickness adapter is the stud spinning in the adapter. The splines on the stud is very short. I believe the studs could be pinned to avoid the...
07-30-2018, 11:58 AM
Replies: 2
Views: 147
Posted By WVZR-1

GM SPO mentions 1/2-20 for LT engines but...

GM SPO mentions 1/2-20 for LT engines but mentions also a 2d design for '96 that's M12-1.75. I've never seen an M12-1.75 but I've never owned a '96. Could you expect either? Maybe!!

!0 or so years...
07-25-2018, 05:46 AM
Replies: 4
Views: 196
Posted By WVZR-1

Maybe this has failed. I don't know that this...

Maybe this has failed. I don't know that this link will stick. If this has failed buy a switch.

https://www.amazon.com/ACDelco-10497876-Signal-Switch-Spring/dp/B0013FTYKS

I'd think it odd for...
07-22-2018, 11:32 AM
Replies: 6
Views: 186
Posted By WVZR-1

1st requirement would be A4 or M6? There's...

1st requirement would be A4 or M6? There's internal differences in dimmer/wiper, SIR etc but so long as you 'paid attention' to which you used there's certainly options that you could maybe consider....
07-19-2018, 08:22 AM
Replies: 15
Views: 568
Posted By WVZR-1

Might this be your VIN? 1G1YY225XT5113924 Might...

Might this be your VIN? 1G1YY225XT5113924 Might be easier for you to compare using the last 8 of the VIN vs attempting a match of just the last 5. It was quite easy to build a coupe VIN with an LT5.....
07-18-2018, 10:01 AM
Replies: 15
Views: 568
Posted By WVZR-1

If the LT4 fit the VIN 'restraints' a phone call...

If the LT4 fit the VIN 'restraints' a phone call to a local dealer would validate if the recall was thought to have been accomplished. It would mean at least the 'paper' was done. The work? Most...
07-18-2018, 07:05 AM
Replies: 2
Views: 230
Posted By WVZR-1

I don't believe it should be an issue if you...

I don't believe it should be an issue if you don't mind losing the ABS. In an earlier thread I mentioned changing to '91+ spindles to use on earlier cars but a few weeks later I had rethought that...
07-15-2018, 08:45 PM
Replies: 4
Views: 157
Posted By WVZR-1

See if after you remove the handle the...

See if after you remove the handle the replacement can be installed with the 'rod and clip' attached to the handle. If yes then I'd think it easier to drop the rod into the latch. I put may car back...
07-14-2018, 10:02 AM
Replies: 9
Views: 325
Posted By WVZR-1

YES on the 3.73 - here in the WV 'twisties' I...

YES on the 3.73 - here in the WV 'twisties' I thought 3.73 might be ideal.

Do the math for 3.73 - 3.90 and 4.10, The 3.90 never gets much conversation but I believe it would make many very happy....
07-13-2018, 03:28 AM
Replies: 6
Views: 290
Posted By WVZR-1

Look at 6E3-52 in the '85 FSM - That shows the BO...

Look at 6E3-52 in the '85 FSM - That shows the BO module wiring and also the connector just above it. Maybe this eBay offering could be used for your wire ID also I have no idea not ever having owned...
07-12-2018, 08:39 PM
Replies: 12
Views: 382
Posted By WVZR-1

FSM 10-17 image 10-24 and door lock cylinder...

FSM 10-17 image 10-24 and door lock cylinder assembly is in a couple pages earlier. There's not an alarm pawl for '85 I see looking at the FSM.

I tried to get a snapshot inside of my door but the...
07-10-2018, 04:41 PM
Replies: 10
Views: 340
Posted By WVZR-1

Have you actually measured the HEX of the nuts?...

Have you actually measured the HEX of the nuts? I've absolutely no experience with the later C4 BPM Valve but all of the FSM specs seem to mention 13 lb ft for flare nuts every where (BPM Valve...
07-10-2018, 07:40 AM
Replies: 10
Views: 340
Posted By WVZR-1

Post a link to that 'instructional video' so that...

Post a link to that 'instructional video' so that you can get very direct responses. If that were so every time a brake hose was removed the ISO/BUBBLE would be unusable. The same would be said of...
07-08-2018, 03:02 PM
Replies: 4
Views: 294
Posted By WVZR-1

Looks to be the 'DEFOGGER CONTROL' . Wires...

Looks to be the 'DEFOGGER CONTROL' . Wires should be PNK/BLK, ORN, BLK/WHT and PPL. Do you have the FSM?
07-07-2018, 08:22 PM
Replies: 12
Views: 420
Posted By WVZR-1

The Starter Enable Relay is just left of the...

The Starter Enable Relay is just left of the column - you didn't answer the question > do you have the FSM? Did you check the PURPLE wire at the starter when 'KEY TO START' and also the larger cable...
07-03-2018, 11:08 AM
Replies: 11
Views: 341
Posted By WVZR-1

Yes - any 'HEXw/notch' is Metric spec.

Yes - any 'HEXw/notch' is Metric spec.
07-02-2018, 08:43 AM
Replies: 11
Views: 341
Posted By WVZR-1

I'd think you return the evap core and get a...

I'd think you return the evap core and get a correct one. I've never seen anyone mix/match Metric spec to earlier SAE spec fittings. The 'notch' in the hex of your evap tells me it's Metric spec and...
06-24-2018, 10:22 AM
Replies: 8
Views: 241
Posted By WVZR-1

To defeat it just remove the 'hatch' circuit...

To defeat it just remove the 'hatch' circuit breaker in the fuse box.Disconnecting the battery I'd think is extreme! Do your courtesy lights function correctly?
06-21-2018, 08:48 AM
Replies: 27
Views: 1,019
Posted By WVZR-1

I have this part # in a '90 SPO catalog for a...

I have this part # in a '90 SPO catalog for a 'coupe only' - #15 in this image.




...
06-13-2018, 08:32 AM
Replies: 10
Views: 262
Posted By WVZR-1

^^^ Good job!! Sometimes 'IN LIVING...

^^^

Good job!!

Sometimes 'IN LIVING COLOR' just works. Your snapshot pretty much confirms the FSM 8A-201 is correct.
06-12-2018, 10:10 AM
Replies: 4
Views: 188
Posted By WVZR-1

Inner tie rod -- looks to me that '88 - '92 are...

Inner tie rod -- looks to me that '88 - '92 are the same and the '93+ are different at least by part #. The difference appears to be internals and rack body because the boots have different part #...
06-12-2018, 09:37 AM
Replies: 8
Views: 232
Posted By WVZR-1

If I had 'known' I would have told you - I don't...

If I had 'known' I would have told you - I don't know why you'd consider eBay. I gave you 2 part #'s you should be able to buy/try local!!!

From the looks of your return line (THE KINK) I'd say...
06-11-2018, 07:08 PM
Replies: 10
Views: 262
Posted By WVZR-1

If you have the actual Helm FSM HAZARD 8A-201-20...

If you have the actual Helm FSM HAZARD 8A-201-20 FIG #33 and the DIRECTIONAL 8A-201-24 #41 & 8A-201-25 #42

BOOK 2 8A-201 is after the wiring diagrams. You should have no issues.
Showing results 1 to 25 of 500
 


 
Forum Jump

Sponsored Ads
Vendor Directory

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.