CorvetteForum - Chevrolet Corvette Forum Discussion - Search Results



Showing results 1 to 15 of 15
Search took 0.02 seconds.
Search: Posts Made By: Donald #31176
Forum: C1 & C2 Corvettes 02-14-2017, 06:01 PM
Replies: 4
Views: 311
Posted By Donald #31176
A graphite base lube like Kable Ease works well....

A graphite base lube like Kable Ease works well. You will need to remove the cable from the dash side as there is a bulb on that side of the cable that prevents you from removing the cable on the...
Forum: C1 & C2 Corvettes 01-19-2017, 09:08 AM
Replies: 13
Views: 537
Posted By Donald #31176
When repros were not available I had my original...

When repros were not available I had my original re cored. Still going strong after 25 years.
Forum: C1 & C2 Corvettes 12-01-2016, 09:14 AM
Replies: 8
Views: 442
Posted By Donald #31176
Most original C-1 caps are Non vented . 56 and...

Most original C-1 caps are Non vented . 56 and some 57s are vented but the originals have a concentric circle front design.
Forum: C1 & C2 Corvettes 06-19-2016, 10:03 AM
Replies: 7
Views: 510
Posted By Donald #31176
Is this what youre looking for? ...

Is this what youre looking for?

http://www.ebay.com/itm/252040568540

http://www.gccorvettes.com/catalogs/56-57Catalog.pdf
Forum: C1 & C2 Corvettes 06-18-2016, 07:40 PM
Replies: 26
Views: 1,080
Posted By Donald #31176
There is an battery door in the drivers side...

There is an battery door in the drivers side wheel well to access the installation and removal of the battery. A group 24 battery is the size you need.
Forum: C1 & C2 Corvettes 05-31-2016, 08:54 AM
Replies: 21
Views: 1,543
Posted By Donald #31176
The following are B28 P/Ns B28 > > > NAPA...

The following are B28 P/Ns

B28
> > > NAPA VC 1810
> > > AC D1312C
> > > STANDARD VC 177
> > > NIEHOFF DR 305
> > > BW V329

The B28 which is made by Standard Auto Products was discontinued...
Forum: C1 & C2 Corvettes 05-19-2016, 05:01 PM
Replies: 5
Views: 461
Posted By Donald #31176
5 to 10 thousands drive gear end play works well....

5 to 10 thousands drive gear end play works well. As far as points read the following

http://www.ncrs.org/forums/showthread.php?83936-NAPA-Echlin-ignition-points-(contact-set)&highlight=point
Forum: C1 & C2 Corvettes 05-08-2016, 10:35 AM
Replies: 3
Views: 444
Posted By Donald #31176
62 NCRS TIMJG sez "block casting date must...

62 NCRS TIMJG sez "block casting date must precede ID engine assembly date generally by no more than than 2 weeks."
Forum: C1 & C2 Corvettes 04-01-2016, 09:45 AM
Replies: 5
Views: 675
Posted By Donald #31176
Default Re: C2 Front / Rear alignment specs ...

Default Re: C2 Front / Rear alignment specs

Front camber: 0 deg.
Front caster: as much as possible up to 2.5 deg. within the adjustment range for power steering.
Front toe-in: 1/32"...
Forum: C1 & C2 Corvettes 03-18-2016, 11:23 PM
Replies: 2
Views: 353
Posted By Donald #31176
From NCRS site JohnZ post. ...

From NCRS site JohnZ post.

http://www.ncrs.org/forums/showthread.php?86490-C1-Body-mount-shims&highlight=body+shims+number
Forum: C1 & C2 Corvettes 02-24-2016, 04:57 PM
Replies: 21
Views: 1,192
Posted By Donald #31176
I believe the armature and field coils for a 35...

I believe the armature and field coils for a 35 amp generator are as follow

armature- Delco #1940161
field coils- Delco #1922701

2268 generator (drive end plate) Delco 1947307-nubs @ 3 & 9...
Forum: C1 & C2 Corvettes 12-23-2015, 06:17 PM
Replies: 10
Views: 790
Posted By Donald #31176
If they re RPO 276 wide wheels (15 x 5 1/2) they...

If they re RPO 276 wide wheels (15 x 5 1/2) they are riveted. Otherwise the common 62 wheels were welded.

PS Another source for C-1 wheels is George Stelzer aka Vettewheelman on Ebay.
Phone #...
Forum: C1 & C2 Corvettes 11-07-2015, 11:58 AM
Replies: 25
Views: 958
Posted By Donald #31176
Assuming your engine has a 30-30 cam & your idle...

Assuming your engine has a 30-30 cam & your idle vacuum is about 10/11 inches HG you need a Standard Auto product p/n VC 177 stamped B28. Other P/Ns are

ACDelco 1312C
Borg W. V329
Niehoff Dr...
Forum: C1 & C2 Corvettes 10-01-2015, 10:30 AM
Replies: 8
Views: 523
Posted By Donald #31176
I believe Delco Remy specs called for 3K ohms-5K...

I believe Delco Remy specs called for 3K ohms-5K ohms per foot.
Forum: C1 & C2 Corvettes 09-16-2015, 07:43 PM
Replies: 57
Views: 2,403
Posted By Donald #31176
Is the intake manifold heat cross over blocked...

Is the intake manifold heat cross over blocked off?
Is the heat riser on the exhaust manifold working or wired open?
New Pertronix ignitors require 12 volts to run. Perhaps the coil is mismatched...
Showing results 1 to 15 of 15

 
Forum Jump

All times are GMT -4. The time now is 10:15 PM.