CorvetteForum - Chevrolet Corvette Forum Discussion - Search Results

Notices
Search: Posts Made By: CA_WxMan
Showing results 1 to 17 of 17
Search took 2.93 seconds.
01-23-2019, 10:43 PM
Replies: 26
Views: 1,795
Posted By F22

Here's my solution to keeping oil off the headers...

Here's my solution to keeping oil off the headers when changing your oil filter.

...
10-14-2018, 12:16 PM
Replies: 8
Views: 579
Posted By GTR1999

Some points to consider Terminology = the...

Some points to consider

Terminology = the name of the housing is Carrier, the posi is the Case. To avoid confusion I call the carrier a housing and the posi the case

The 1350 & 1480 axles use...
09-18-2018, 03:29 AM
Replies: 24
Views: 1,848
Posted By Greg

Easy Dash Bulb Socket Upgrade.

I like easy.
If you've been inside half as many C3 dashboards as I have, then you know what a pain in the ass the original single wire dash bulb sockets can become with age. The ground rings...
07-10-2018, 03:06 PM
Replies: 12
Views: 756
Posted By cuisinartvette

QMP racing engines in Chatsworth has a CNC...

QMP racing engines in Chatsworth has a CNC program to do just this. Used them many times.
818) 576-0816
03-03-2018, 07:10 AM
Replies: 21
Views: 1,083
Posted By RIFRAFT

Chris, beginners are always welcome at the Byrd...

Chris, beginners are always welcome at the Byrd events. Open courses, good speed and transitions, and easy to read. If it fits your schedule I highly recommend going.

There are no Camarillo...
02-11-2018, 07:51 PM
Replies: 6
Views: 826
Posted By ignatz

I installed mine strictly for autocross. I...

I installed mine strictly for autocross. I wanted better seats and harness. The installation wasn't too bad, but the bar has some distinct disadvantages. To put the t-tops in the back, you need to...
02-03-2018, 07:22 PM
Replies: 27
Views: 2,606
Posted By Alan 71

Hi L, The separator is pretty simple so they...

Hi L,
The separator is pretty simple so they really don't 'go bad'.
Sometimes the type I pictured can leak because of a crack.
I'm really not sure how the one on your tank might be configured....
12-27-2017, 02:11 PM
Replies: 7
Views: 1,116
Posted By Mooser

https://cimg2.ibsrv.net/gimg/www.corvetteforum.com...

https://cimg2.ibsrv.net/gimg/www.corvetteforum.com-vbulletin/799x500/80-c3vetterotordimensions_757cd524ff0cd2a574f8874b9498e7d003f2e046.jpg
11-07-2017, 11:13 PM
Replies: 997
Views: 470,755
Posted By 3JsVette

CA_WxMan Nice choice with the wheel/tire...

CA_WxMan Nice choice with the wheel/tire combination. The wheels compliment the color of the car perfectly. You certainly filled the wheel wells. :thumbs:
On a side note that 1st picture is poster...
Forum: C3 General
11-05-2017, 12:49 AM
Replies: 3,767
Views: 287,701
Posted By Richard454

Idiot Lights...

Got my gauges finalized...well almost...

I was looking for something to replace the seatbelt light and push button then ended up completely reconfiguring it-

The camera really doesn't do it...
04-30-2017, 09:09 AM
Replies: 14
Views: 1,071
Posted By Dynra Rockets

As long as you are pressing stuff in, might as...

As long as you are pressing stuff in, might as well take a look at your lower shock mounts also.

The factory specifies a BP19 bar pin type lower mount with 2.62" holt-to-hole mounting and 3.19"...
04-27-2017, 09:20 PM
Replies: 997
Views: 470,755
Posted By SpeedRacerMach

Chris, I have to correct my self, these are not...

Chris,
I have to correct my self, these are not 18x9s, they are 18x8s. So the rim width is pretty much comparable to an original 15x8 with the exception of the offset. Originals had a -3 offset,...
04-27-2017, 04:58 PM
Replies: 997
Views: 470,755
Posted By FKING1

CORRECTION I run 275's rear & 245's frt on...

CORRECTION

I run 275's rear & 245's frt on 18x9.5. Car is lowered.
No rubs.
Forum: C3 General
04-16-2017, 01:21 PM
Replies: 4
Views: 347
Posted By Alan 71

Hi dp, The AIM indicates a small screw/bolt...

Hi dp,
The AIM indicates a small screw/bolt goes up through the bracket on the duct into a u-clip on the bracket for the odometer re-set and courtesy lamp.
Is there a hole in the bracket where the...
Forum: C3 General
04-13-2017, 06:36 PM
Replies: 3,756
Views: 221,399
Posted By papawana

wiring diagrams

great story!!! thanks for the thanks...I have sent out 10's of thousands of these diagrams to help fellow corvette owners...you will notice that very few check the thank you finger for my...
Forum: C3 General
01-07-2017, 04:08 PM
Replies: 3,756
Views: 221,399
Posted By papawana

wiring diagrams

diagrams sent
Forum: C3 General
12-10-2016, 07:48 PM
Replies: 9
Views: 653
Posted By kanvasman

West System products at a marine supply place...

West System products at a marine supply place have different catalysts depending on the temp. And their set up is ALMOST foolproof, one squirt from each can ( different size dispensers already...
Showing results 1 to 17 of 17


 
Forum Jump

Sponsored Ads
Vendor Directory

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.