CorvetteForum - Chevrolet Corvette Forum Discussion - Search Results

Notices
Search: Posts Made By: SteveOO
Showing results 1 to 16 of 16
Search took 0.04 seconds.
01-12-2018, 09:48 AM
Replies: 52
Views: 11,923
Posted By SteveOO

My TX Speed kit came with stock length push rods....

My TX Speed kit came with stock length push rods. I think your rocker bolts are to long and bottoming out in head before the saddle gets tight. That's what mine did, using the new bolts in the kit. I...
01-07-2018, 09:49 AM
Replies: 42
Views: 10,137
Posted By SteveOO

I will sell the kent moore tool now that I am...

I will sell the kent moore tool now that I am done with it. I paid $50.
12-26-2017, 11:06 PM
Replies: 10
Views: 5,352
Posted By SteveOO

Kicked off my high heels, maxed out my torque...

Kicked off my high heels, maxed out my torque wrench 200+ ft #, got the 90 degrees. Yes new bolt came with kit.
12-26-2017, 07:08 PM
Replies: 10
Views: 5,352
Posted By SteveOO

I am checking the torque on the final 90 degrees...

I am checking the torque on the final 90 degrees and I am getting 110 ft #, from 12 oclock to 12:30. Any one check the torque on this? So I have gone form 48 to 110 pounds in 1/16 of a turn, ie its...
12-26-2017, 06:53 PM
Replies: 52
Views: 11,923
Posted By SteveOO

I wanted to hear it run before installing timing...

I wanted to hear it run before installing timing chain cover and accessories. If I had to tear it back down its quicker and cheaper. Also wanted to verify oil pressure in case the pump had to be...
12-25-2017, 06:13 PM
Replies: 52
Views: 11,923
Posted By SteveOO

I warmed the oil pan (don't ask how)- restarted,...

I warmed the oil pan (don't ask how)- restarted, and am getting high oil pressure at this location, when I backed out sensor it squirted 10 ft. Not sure why sensor is not reading.
I am also now...
12-25-2017, 04:20 PM
Replies: 52
Views: 11,923
Posted By SteveOO

I warmed the oil pan (don't ask how)- restarted,...

I warmed the oil pan (don't ask how)- restarted, and am getting high oil pressure at this location, when I backed out sensor it squirted 10 ft.
I am also now getting oil to most rockers.
The engine...
12-24-2017, 01:57 PM
Replies: 52
Views: 11,923
Posted By SteveOO

l86

l86
12-24-2017, 10:58 AM
Replies: 52
Views: 11,923
Posted By SteveOO

With the dod oil holes plugged, how would the...

With the dod oil holes plugged, how would the sender unit ever get oil pressure in this location? The valley cover is getting no oil.??
12-23-2017, 08:51 PM
Replies: 52
Views: 11,923
Posted By SteveOO

Oil Pump, I did not have the alignment tool. I...

Oil Pump, I did not have the alignment tool. I loosened the 4 bolts and spun the engine with the starter, self centering the gears. We will see if this works. I'm hopeful.
Lifters, I am re-using the...
12-23-2017, 06:39 PM
Replies: 52
Views: 11,923
Posted By SteveOO

cam dod delete Tx Speed kit

I have been following this thread as I've been installing my Tx Speed cam, dod delete, cam phase limiter, trunion upgrade, header kit. 2017 Denali L86. Thread has been real asset, well done Thanks!...
12-16-2017, 08:59 PM
Replies: 42
Views: 10,137
Posted By SteveOO

How much force should it take? I am concerned if...

How much force should it take? I am concerned if it is not seated it will distort my pre-load measurements. It does not just slide on over the lifter.
12-16-2017, 08:11 PM
Replies: 42
Views: 10,137
Posted By SteveOO

I am installing a Texas Speed cam with 32% fuel...

I am installing a Texas Speed cam with 32% fuel lobe, they supplied a lash cap. I have my valley cover off. It looks like there is a factory lash cap on the end of the push rod. The cap wobbles like...
11-22-2017, 02:53 PM
Replies: 52
Views: 11,923
Posted By SteveOO

Lonnie at Texas Speed told me today that the oil...

Lonnie at Texas Speed told me today that the oil pump can be aligned by inserting feeler gauge .002-.003 around the crankshaft to center the gear on the shaft. He also said the 4 13mm bolts can be...
11-21-2017, 01:31 PM
Replies: 52
Views: 11,923
Posted By SteveOO

Here is a link for the Oil Pump housing alignment...

Here is a link for the Oil Pump housing alignment tool.
@ $125 its a little pricy
Could I scribe the alignment on a template using the bolt holes as a work around? or is this absolutely the way to...
11-21-2017, 12:50 PM
Replies: 52
Views: 11,923
Posted By SteveOO

May i ask how you cleaned the pistons, head deck...

May i ask how you cleaned the pistons, head deck and exhaust ports?
thx
Showing results 1 to 16 of 16


 
Forum Jump

Sponsored Ads
Vendor Directory

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.