[Z06] DashLogic display controller for Z06
Thread Starter
Former Vendor
Joined: Sep 2013
Posts: 295
Likes: 1
From: Utah
DashLogic Z06 display controller now with NPP control
DashLogic is the most advanced way of displaying vehicle data to date. There is nothing to install, no programing, no changes to your vehicle in any way. Simply plug in the DashLogic device to your vehicles OBD-II port and DashLogic turns your factory dashboard display into a fully customizable gauge canvas. See all of the data your vehicle has to offer on your Driver Information Center or Head-Up Display. DashLogic doesn't stop there, you can also customize visual and audible alerts that you set to any condition for any vehicle value, fully customizable by you. Just in case your car doesn't have a sensor for a value you would like to watch, DashLogic also has two auxiliary inputs so you can add up to two aftermarket sensors to be viewed on your DIC or HUD as well as be used for alerts. The DashLogic alerts system is a very advanced tool, this is not your run of the mill type of simple alert that only watches one value. DashLogic will take into account several conditions for one alert, all of those conditions fully customizable by you.
DashLogic is also a controller for NPP exhaust systems using the mirror switch.
Also here is a quick example of a simple 3500 RPM Alert
DashLogic is also a controller for NPP exhaust systems using the mirror switch.
Also here is a quick example of a simple 3500 RPM Alert
Last edited by PalmerPerformance; Oct 15, 2013 at 06:44 PM.
Thread Starter
Former Vendor
Joined: Sep 2013
Posts: 295
Likes: 1
From: Utah
Pro
Joined: Aug 2004
Posts: 511
Likes: 0
From: Normal IL
Purchased this a couple weeks ago and finally got it set up this weekend. Very easy to set up a personalized display and warnings on the computer.
Just need the snow to melt so I can get out and test it out
Just need the snow to melt so I can get out and test it out
Thread Starter
Former Vendor
Joined: Sep 2013
Posts: 295
Likes: 1
From: Utah
New Firmware available. This firmware has added a PID so you can set an alarm to washer fluid level (for methanol injection cars), added MAF Hz, and Vehicle voltage.
http://www.palmerperformance.com/dow...ware_v1.17.ehx
http://www.palmerperformance.com/dow...ware_v1.17.ehx
Team Owner
Joined: May 2004
Posts: 26,345
Likes: 232
From: SoCal
New Firmware available. This firmware has added a PID so you can set an alarm to washer fluid level (for methanol injection cars), added MAF Hz, and Vehicle voltage.
http://www.palmerperformance.com/dow...ware_v1.17.ehx
http://www.palmerperformance.com/dow...ware_v1.17.ehx
DH
Thread Starter
Former Vendor
Joined: Sep 2013
Posts: 295
Likes: 1
From: Utah
Yes it does. You can even set alarms to chime vehicle chimes and show on the display any time you are knocking.
Here is a pre tune demo
You can also put the knock amount with the alert text which I should have done in that video.... It could have said "Knocking 5.2*" on the display. You also don't have to be viewing knock on the display for the alert to work, it will show no matter what data you are viewing.
Here is a pre tune demo
You can also put the knock amount with the alert text which I should have done in that video.... It could have said "Knocking 5.2*" on the display. You also don't have to be viewing knock on the display for the alert to work, it will show no matter what data you are viewing.
Last edited by PalmerPerformance; Jun 14, 2014 at 09:28 PM.
Team Owner
Joined: May 2004
Posts: 26,345
Likes: 232
From: SoCal
Yes it does. You can even set alarms to chime vehicle chimes and show on the display any time you are knocking.
Here is a pre tune demo
DashLogic Knock Alarm - YouTube
You can also put the knock amount with the alert text which I should have done in that video.... It could have said "Knocking 5.2*" on the display. You also don't have to be viewing knock on the display for the alert to work, it will show no matter what data you are viewing.
Here is a pre tune demo
DashLogic Knock Alarm - YouTube
You can also put the knock amount with the alert text which I should have done in that video.... It could have said "Knocking 5.2*" on the display. You also don't have to be viewing knock on the display for the alert to work, it will show no matter what data you are viewing.
By looking at your website It looks like AFR will require the PLX and WB 02 sensor, correct?
I have an Aim Solo DL that plugs into the OBII port. Is there a way to run both simultaneously ???
DH
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Thread Starter
Former Vendor
Joined: Sep 2013
Posts: 295
Likes: 1
From: Utah
You can use any Wideband with a 0-5v output, it doesn't have to be PLX, but we do offer a discount package with the PLX Wideband. I know that DashLogic will work with the Solo, but I can't be for sure our message requests won't confuse the Solo? What displays on the Solo? Is it possible to have it not requesting the same data as the DashLogic is showing?
Team Owner
Joined: May 2004
Posts: 26,345
Likes: 232
From: SoCal
You can use any Wideband with a 0-5v output, it doesn't have to be PLX, but we do offer a discount package with the PLX Wideband. I know that DashLogic will work with the Solo, but I can't be for sure our message requests won't confuse the Solo? What displays on the Solo? Is it possible to have it not requesting the same data as the DashLogic is showing?
But it only shows time on its display while in track mode.
It does not collect maf, spark, KR etc.
I'm mostly interested in KR
And I'm not going to install a wide band.
DH
Team Owner
Joined: May 2004
Posts: 26,345
Likes: 232
From: SoCal
You can use any Wideband with a 0-5v output, it doesn't have to be PLX, but we do offer a discount package with the PLX Wideband. I know that DashLogic will work with the Solo, but I can't be for sure our message requests won't confuse the Solo? What displays on the Solo? Is it possible to have it not requesting the same data as the DashLogic is showing?
DH
Thread Starter
Former Vendor
Joined: Sep 2013
Posts: 295
Likes: 1
From: Utah
Thread Starter
Former Vendor
Joined: Sep 2013
Posts: 295
Likes: 1
From: Utah
It is not an ELM327 device, it will not work as an ELM device. We will have DashLogic added as a connection hardware on our next ScanXL update, and it will be able to log on that Windows software.
