Parts No Longer Made or Stocked for C6Z06 or ZR1
Thread Starter
Drifting
Joined: Sep 2000
Posts: 1,579
Likes: 415
From: Fulshear TX
Parts No Longer Made or Stocked for C6Z06 or ZR1
Let's start the list and also provide links to new or reconditioned substitute parts: Updated 11/25/2025.
Front fenders C6 Z06 Front Fenders | Faircloth Composites – Faircloth composites
Starters
ABS.TC Modules
C6Z06 front fenders Fairclothcomposites@gmail.com
C6Z06 Starters Powermaster 9509
C6Z06 ABS/TC Modules
steering rack
C6Z06 rear fenders C6Z06 front fenders Fairclothcomposites@gmail.com Note that these replacements will be carbon fiber, not SMC so weight will be less and cost will be greater.
ZR1 side skirts C6Z06 front fenders Fairclothcomposites@gmail.com Ditto above.
ZR1 splitter C6Z06 front fenders Fairclothcomposites@gmail.com Ditto above
C6Z06 Doors C6Z06 front fenders Fairclothcomposites@gmail.com Ditto above
C6/ Z06/ZR1 front bumpers
ZR1 CCBs
ZR1 fuel pumps T1 Automotive ESLM?
ZR1 fuel sending units
Fuel tank crossover/coupler
FE5 Magnaride rear shocks. Use from Cadillac XLR?
HVAC module - rebuild yours from Automotive Scientific in Rogersville, TN
LS7 long block crate engine
ZR1 power steering pump- Holley 198-103
ZR1 power steering pulley/bracket
ZR1 power steering reservoir-occasionally found on eBay. Cadillac XLR-V uses the same one.
ZR1 water pump
Several people have wanted to complain to GM's highest levels about GM's apparent decision not to support our C6Z06 and C6ZR1 cars with replacement parts. Please send your comments, suggestions, and complaints to: Mary Barra, GM CEO at Mary.bara@gm.com and her team's email address is execreferral@gm.com regarding replacement parts availability for our C6Z06 and C6ZR1 cars.
Front fenders C6 Z06 Front Fenders | Faircloth Composites – Faircloth composites
Starters
ABS.TC Modules
C6Z06 front fenders Fairclothcomposites@gmail.com
C6Z06 Starters Powermaster 9509
C6Z06 ABS/TC Modules
steering rack
C6Z06 rear fenders C6Z06 front fenders Fairclothcomposites@gmail.com Note that these replacements will be carbon fiber, not SMC so weight will be less and cost will be greater.
ZR1 side skirts C6Z06 front fenders Fairclothcomposites@gmail.com Ditto above.
ZR1 splitter C6Z06 front fenders Fairclothcomposites@gmail.com Ditto above
C6Z06 Doors C6Z06 front fenders Fairclothcomposites@gmail.com Ditto above
C6/ Z06/ZR1 front bumpers
ZR1 CCBs
ZR1 fuel pumps T1 Automotive ESLM?
ZR1 fuel sending units
Fuel tank crossover/coupler
FE5 Magnaride rear shocks. Use from Cadillac XLR?
HVAC module - rebuild yours from Automotive Scientific in Rogersville, TN
LS7 long block crate engine
ZR1 power steering pump- Holley 198-103
ZR1 power steering pulley/bracket
ZR1 power steering reservoir-occasionally found on eBay. Cadillac XLR-V uses the same one.
ZR1 water pump
Several people have wanted to complain to GM's highest levels about GM's apparent decision not to support our C6Z06 and C6ZR1 cars with replacement parts. Please send your comments, suggestions, and complaints to: Mary Barra, GM CEO at Mary.bara@gm.com and her team's email address is execreferral@gm.com regarding replacement parts availability for our C6Z06 and C6ZR1 cars.
Last edited by Z.06; Nov 25, 2025 at 09:43 PM. Reason: Added comment
Popular Reply
Oct 21, 2025, 11:12 PM
Thread Starter
Drifting
Joined: Sep 2000
Posts: 1,579
Likes: 415
From: Fulshear TX
We need to understand how deep of a hole we are in to keep the best Corvette Z06 version alive. Also we need to encourage the aftermarket to address this problem.
Thread Starter
Drifting
Joined: Sep 2000
Posts: 1,579
Likes: 415
From: Fulshear TX
I agree this list will get longer. My intent is to save time for people who need to replace discontinued OEM factory parts, such that they are not having to call a dozen potential suppliers to find what they need. I have been on Corvette Forum for 25 years now, and I cannot remember seeing something like this, but if something already exists -- please let me know.
I think the guidelines for putting a part on the list should be that it is a factory C6Z06 or C6ZR1 factory part which is no longer in production. People who add out of stock parts are not required to add alternate suppliers but they can if they have them. Other people can add alternate suppliers as well. I think we should not list used take-off parts as a supplier/source, but a reputable parts rebuilder should be OK.
C6Z06 front fenders Fairclothcomposites@gmail.com
Starters Powermaster 9509
ABS/TC Modules ?
RedZ4me: When I saw your list, I had to wonder if these parts are all ZR1 specific? If so, we need to specify that as well. Did you go looking for these parts on GMpartsdirect? What did you substitute for your car?
I think the guidelines for putting a part on the list should be that it is a factory C6Z06 or C6ZR1 factory part which is no longer in production. People who add out of stock parts are not required to add alternate suppliers but they can if they have them. Other people can add alternate suppliers as well. I think we should not list used take-off parts as a supplier/source, but a reputable parts rebuilder should be OK.
C6Z06 front fenders Fairclothcomposites@gmail.com
Starters Powermaster 9509
ABS/TC Modules ?
RedZ4me: When I saw your list, I had to wonder if these parts are all ZR1 specific? If so, we need to specify that as well. Did you go looking for these parts on GMpartsdirect? What did you substitute for your car?
Melting Slicks
Joined: Mar 2006
Posts: 2,249
Likes: 297
From: Woodbury MN
I think the purpose of this list is to not just to list discontinued parts, but to post where one can find replacement parts.
Racer
Joined: Mar 2023
Posts: 344
Likes: 144
From: Saint Louis
Quality parts are hard to find, I hate when looking for a part, some Chinese crap comes up. I know a lot of OEM parts are made in China but they are a least supposed to be made to manufacturers specs. The knockoff stuff is of very poor quality.
It would be nice if we had access to GM's parts locator so we could find NOS parts in dealers inventory not just at the online retail outlets.
It would be nice if we had access to GM's parts locator so we could find NOS parts in dealers inventory not just at the online retail outlets.
Pro
Joined: Feb 2005
Posts: 732
Likes: 276
this would be really helpful. My Z was hit last December and it took 6 months to get body parts. Faircloth couldn’t say how long a wait so I had body shop contact Corvette Central. They offered a Fiberglass fender for $3000 and about 6 weeks plus. I looked farther down their list and found a pair of ZR1 carbon fiber fenders for $2200 for the pair and got them in 4 weeks.
Thread Starter
Drifting
Joined: Sep 2000
Posts: 1,579
Likes: 415
From: Fulshear TX
Parts No Longer Made or Stocked for C6Z06 and ZR1
You are exactly correct and as Bruno and Rocsvette expressed it gives us the opportunity to signal the quality of the replacement parts as well as the time frame needed to get them. I had a recent experience of cracking an OEM carbon fiber front fender. The problem did not disable the car. I went to Faircloth to have a replacement built, and the result was a very high-quality part albeit several weeks later. This worked well for me, because I could accept the wait time to get the best part. My reality was that the only alternative was to have a body shop acquire a damaged OEM fender salvaged from a wrecked Z06 and repair it with filler. I did not accept this alternative.
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
10 Revolutionary 'Corvette Firsts' Most People Don't Know
Joe Kucinski
5 Reasons to Upgrade to an LS6-Powered Corvette; 5 Reasons to Stay LT2
Michael S. Palmer
2027 Corvette vs The World: Every C8 vs Its Closest Competitor
Joe Kucinski
10 Most Common Corvette Problems of the Last 20 Years!
Joe Kucinski
5 MOST and 5 LEAST Popular Corvette Model Years in History!
Joe Kucinski
2027 Corvette Buyer's Guide: Everything You Need to Know!
Joe Kucinski
10 Things C8 Corvette Owners Hate (But Won't Tell You)
Joe Kucinski
10 Best Corvettes Coming to Barrett-Jackson Palm Beach 2026!
Brett Foote
Every Corvette Grand Sport Explained! (C2, C4, C6, C7, & C8)
Joe Kucinski
Le Mans Master
Joined: May 2011
Posts: 5,186
Likes: 545
From: Ontario
I agree this list will get longer. My intent is to save time for people who need to replace discontinued OEM factory parts, such that they are not having to call a dozen potential suppliers to find what they need. I have been on Corvette Forum for 25 years now, and I cannot remember seeing something like this, but if something already exists -- please let me know.
I think the guidelines for putting a part on the list should be that it is a factory C6Z06 or C6ZR1 factory part which is no longer in production. People who add out of stock parts are not required to add alternate suppliers but they can if they have them. Other people can add alternate suppliers as well. I think we should not list used take-off parts as a supplier/source, but a reputable parts rebuilder should be OK.
C6Z06 front fenders Fairclothcomposites@gmail.com
Starters Powermaster 9509
ABS/TC Modules ?
RedZ4me: When I saw your list, I had to wonder if these parts are all ZR1 specific? If so, we need to specify that as well. Did you go looking for these parts on GMpartsdirect? What did you substitute for your car?
I think the guidelines for putting a part on the list should be that it is a factory C6Z06 or C6ZR1 factory part which is no longer in production. People who add out of stock parts are not required to add alternate suppliers but they can if they have them. Other people can add alternate suppliers as well. I think we should not list used take-off parts as a supplier/source, but a reputable parts rebuilder should be OK.
C6Z06 front fenders Fairclothcomposites@gmail.com
Starters Powermaster 9509
ABS/TC Modules ?
RedZ4me: When I saw your list, I had to wonder if these parts are all ZR1 specific? If so, we need to specify that as well. Did you go looking for these parts on GMpartsdirect? What did you substitute for your car?
Instructor
Joined: May 2024
Posts: 103
Likes: 29
been bothering me for a while that as time goes and I keep reading more and more parts discontinued. I have left and right fuel senders thinking I may need them one day for common p2068 code and have one brand new right side oem side carbon skirt. These three items avail now if anyone needs them. Tube for skirt is big, might be costly to ship from Ontario Canada though.
Le Mans Master
Joined: May 2011
Posts: 5,186
Likes: 545
From: Ontario
Race Director
Joined: Oct 2004
Posts: 12,828
Likes: 4,637
@Z.06 Sometimes the littlest things are really important. As you know, I'm from C5 land. Our fobs have been out of production for many years. You guys might want to check out if there are any fobs left, as I'm sure they're out of production. For the most part, the aftermarket C5 fobs suck......
Thread Starter
Drifting
Joined: Sep 2000
Posts: 1,579
Likes: 415
From: Fulshear TX
C6 Key fobs
@Z.06 Sometimes the littlest things are really important. As you know, I'm from C5 land. Our fobs have been out of production for many years. You guys might want to check out if there are any fobs left, as I'm sure they're out of production. For the most part, the aftermarket C5 fobs suck......
Thread Starter
Drifting
Joined: Sep 2000
Posts: 1,579
Likes: 415
From: Fulshear TX
So here's what I have so far:
C6Z06 front fenders Fairclothcomposites@gmail.com
C6Z06 Starters Powermaster 9509
C6Z06 ABS/TC Modules ?
steering rack
C6Z06 rear fenders C6Z06 front fenders Fairclothcomposites@gmail.com Note that these replacements will be carbon fiber, not SMC so weight will be less and cost will be greater.
ZR1 side skirts C6Z06 front fenders Fairclothcomposites@gmail.com Ditto above.
ZR1 splitter C6Z06 front fenders Fairclothcomposites@gmail.com Ditto above
C6Z06 Doors C6Z06 front fenders Fairclothcomposites@gmail.com Ditto above
ZR1 CCBs
ZR1 fuel pumps
ZR1 fuel sending units
Fuel tank crossover/coupler
There will be others sp please add them. Now we should apply our collective experience to add alternative suppliers of NOS or acceptably rebuilt parts on the list.
C6Z06 front fenders Fairclothcomposites@gmail.com
C6Z06 Starters Powermaster 9509
C6Z06 ABS/TC Modules ?
steering rack
C6Z06 rear fenders C6Z06 front fenders Fairclothcomposites@gmail.com Note that these replacements will be carbon fiber, not SMC so weight will be less and cost will be greater.
ZR1 side skirts C6Z06 front fenders Fairclothcomposites@gmail.com Ditto above.
ZR1 splitter C6Z06 front fenders Fairclothcomposites@gmail.com Ditto above
C6Z06 Doors C6Z06 front fenders Fairclothcomposites@gmail.com Ditto above
ZR1 CCBs
ZR1 fuel pumps
ZR1 fuel sending units
Fuel tank crossover/coupler
There will be others sp please add them. Now we should apply our collective experience to add alternative suppliers of NOS or acceptably rebuilt parts on the list.
Thread Starter
Drifting
Joined: Sep 2000
Posts: 1,579
Likes: 415
From: Fulshear TX
I think it would be to the advantage of the companies in the aftermarket Corvette business to support this post with their knowledge/experience. As GM/Corvette stop supporting our C6Z06 and ZR1 with production and inventory, it is natural for the aftermarket to move in and support that market. C6Z06/ZR1 owners need your support, so the intent of this post is to most efficiently direct current owners to reputable NOS and remanufactured replacement parts. My ask is that you help me update the data, such that the car owners can be efficiently directed to suppliers.
Instructor
Joined: Jan 2006
Posts: 220
Likes: 70
From: Rocky Mountains USA
