**C5 High Horse Power Club**
#121
Le Mans Master
#122
#125
Race Director
Member Since: Dec 2010
Location: Atlanta, GA
Posts: 10,426
Received 1,261 Likes
on
1,056 Posts
2020 Corvette of the Year Finalist (performance mods)
C5 of Year Winner (performance mods) 2019
you have a dyno sheet to prove it?
#126
Add me please
Forged rod and piston 346
Finishline 4l65E
Paxton 2200r
10 rib with flip drive
Pump E and meth
ID1700’s
BTR Equalizer 1 intake
Trickflow 225 heads
Ls2 TB
916 rwhp
753 rwtq
Last edited by EgoKlr; 06-20-2019 at 03:26 AM.
#127
Le Mans Master
my update (finally): still stock short block LS1, TVS2300, heads, cam, exhaust, KillerChiller on pump 93 = 650whp / 630wtq
so how's this work if an electrical storm last week put a queer-tron in the dyno that made it work good enough to tune with but wouldn't let it save pulls in order to print a sheet?
so how's this work if an electrical storm last week put a queer-tron in the dyno that made it work good enough to tune with but wouldn't let it save pulls in order to print a sheet?
#128
Le Mans Master
#129
Race Director
Member Since: Dec 2010
Location: Atlanta, GA
Posts: 10,426
Received 1,261 Likes
on
1,056 Posts
2020 Corvette of the Year Finalist (performance mods)
C5 of Year Winner (performance mods) 2019
my update (finally): still stock short block LS1, TVS2300, heads, cam, exhaust, KillerChiller on pump 93 = 650whp / 630wtq
so how's this work if an electrical storm last week put a queer-tron in the dyno that made it work good enough to tune with but wouldn't let it save pulls in order to print a sheet?
so how's this work if an electrical storm last week put a queer-tron in the dyno that made it work good enough to tune with but wouldn't let it save pulls in order to print a sheet?
#131
Instructor
UPDATE:
04 Base C5
Stock bottom end
Trick Flow Heads
Tourqer V2 Cam
36lb (white) FAST Injectors
Vararam Intake
C6Z Fuel Pump Module
Nitrous Outlet Plate kit Kit: 200 shot
Nitrous Outlet stand alone fuel tank (C16 in tank)
656whp / 692ft/lb
The following users liked this post:
Awesome04Vette (06-16-2019)
#135
Race Director
Member Since: Dec 2010
Location: Atlanta, GA
Posts: 10,426
Received 1,261 Likes
on
1,056 Posts
2020 Corvette of the Year Finalist (performance mods)
C5 of Year Winner (performance mods) 2019
nitrous though so it doesn't count
The following users liked this post:
Awesome04Vette (06-16-2019)
#136
May I join the 700 club?
737whp 655wtq
Bought it barely running and driving about a month ago. Wouldnt even rev past 4000rpm it was running so poorly. Probably have over 100 hours of work into it already basically tearing it down to a shortblock and redoing EVERYTHING.
- SDPC Raceshop iron block 383 stroker. Fully forged and studded top and bottom. -15cc pistons.
- Advanced induction 317 heads
- Chinese stainless headers and xpipe. Billy boat bullet axle back
- A&A corvette TI blower, 3.3" pulley, 8 rib with overdrive balancer and secondary drive system. (I have been told with the 10% overdrive balancer that this might be overdriving the blower)
- 255lph fuel pump in the stock location with fully stock lines and regulator
- 450lph external pump on a hob switch pulling from a bung on the tank feeding a regulator set to 60psi up front
- 100lb injectors
- Tuned by yours truely (Have well over 100 credits purchased through HPT so I have done a few to say the least). Running closed loop and even have functioning knock sensors.
Bought it barely running and driving about a month ago. Wouldnt even rev past 4000rpm it was running so poorly. Probably have over 100 hours of work into it already basically tearing it down to a shortblock and redoing EVERYTHING.
#137
Pro
2003 6spd coupe
PRC stage 2.5 317 heads, 226/228 .600/.600 114
stock bottom
1 7/8” catless ARH’s
A&A V3Ti, 3.8” pulley
A&A single pump fuel system
2 bar Map , Centerforce Dyad clutch
PRC stage 2.5 317 heads, 226/228 .600/.600 114
stock bottom
1 7/8” catless ARH’s
A&A V3Ti, 3.8” pulley
A&A single pump fuel system
2 bar Map , Centerforce Dyad clutch
Last edited by RockyMtC5; 07-04-2019 at 01:53 PM.
#138
Race Director
Member Since: Dec 2010
Location: Atlanta, GA
Posts: 10,426
Received 1,261 Likes
on
1,056 Posts
2020 Corvette of the Year Finalist (performance mods)
C5 of Year Winner (performance mods) 2019
I don't know if the op has any interest in keeping this updated, I tried to contact him awhile back and got no response... maybe someone that knows him could let him know