CorvetteForum - Chevrolet Corvette Forum Discussion
0 2023/05/27 05:41:08
MSD 6A failure, I believe caused by voltage variant of burnt starter wiring. Considered repair, but the power transistors and other devices are at the end of their life expectancy.
MSD 6A failure, I believe caused by voltage variant of burnt starter wiring. Considered repair, but the power transistors and other devices are at the end of their life expectancy.
0 2023/05/31 06:37:58
Mallory Uni-Lite module melted due to engine compartment heat in a V-8 Vega. Just for information. The module still works, but I don't care to trust it.
Mallory Uni-Lite module melted due to engine compartment heat in a V-8 Vega. Just for information. The module still works, but I don't care to trust it.
0 2023/05/31 06:38:17
Vendors were bored to say the least. A lot of parts, but few buyers. 90 + degrees didn't help much as well as 3 or more small town celebrations with car shows within 30 miles of BN.
Vendors were bored to say the least. A lot of parts, but few buyers. 90 + degrees didn't help much as well as 3 or more small town celebrations with car shows within 30 miles of BN.
0 2023/06/03 12:38:46
Great band: Biscuits & Gravy. Didn't display a lot of SEX, but there was no lack of talent. I even chased the wife around for 15 seconds or so.
Great band: Biscuits & Gravy. Didn't display a lot of SEX, but there was no lack of talent. I even chased the wife around for 15 seconds or so.
0 2023/06/03 12:38:54
Plenty of clearance.
Plenty of clearance.
0 2023/06/03 12:59:49
54.5 inch long belt.
54.5 inch long belt.
0 2023/06/03 12:59:59
No Vacuum can, but you can see the wires.
No Vacuum can, but you can see the wires.
0 2023/06/04 12:43:18
0 2023/06/10 18:42:09
0 2023/06/11 06:16:00
A few C3s down the line. Every C series (1 thru 8) was represented somewhere.
A few C3s down the line. Every C series (1 thru 8) was represented somewhere.
0 2023/06/11 10:53:21
What's not to love. Gear Heads swapping lies. Better than any show.
What's not to love. Gear Heads swapping lies. Better than any show.
0 2023/06/11 10:53:33
You have to look close for a couple of C2s 65 and 67. Also had a 58 restomod and an original 58. R66 is behind me. Couldn't get it all.
You have to look close for a couple of C2s 65 and 67. Also had a 58 restomod and an original 58. R66 is behind me. Couldn't get it all.
0 2023/06/11 10:53:45
HD Delco Remy starter with C.I. nose
HD Delco Remy starter with C.I. nose
0 2023/06/18 15:39:45
Brown v.s. black cap solenoids
Brown v.s. black cap solenoids
0 2023/06/18 15:40:04
standard duty starter for 154 tooth flywheel closest to you and heavy duty starter for 168 tooth flywheel generally used on BBs and trucks.
standard duty starter for 154 tooth flywheel closest to you and heavy duty starter for 168 tooth flywheel generally used on BBs and trucks.
0 2023/06/21 14:19:58
BUBBA's best, I guess.
BUBBA's best, I guess.
0 2023/06/25 18:22:43
MSD-6A electronics.
MSD-6A electronics.
0 2023/06/25 18:22:48
Casting number should give you the bore diameter of the master cylinder
Casting number should give you the bore diameter of the master cylinder
0 2023/07/17 18:33:12
Date code stamped and not sure what the 75 means.
Date code stamped and not sure what the 75 means.
0 2023/07/17 18:33:16
You may not be able to read the stamp, it is BS on this 68 master cylinder.
You may not be able to read the stamp, it is BS on this 68 master cylinder.
0 2023/07/17 18:33:23
If it was good enough for Ricky- - - - - -
If it was good enough for Ricky- - - - - -
0 2023/07/21 18:17:18
Broken latch pawl - what are the chances of finding just that piece?
Broken latch pawl - what are the chances of finding just that piece?
0 2023/07/24 14:18:58
Easy access, but does make getting to the negative side of the battery a little harder.
Easy access, but does make getting to the negative side of the battery a little harder.
0 2023/07/27 14:00:49
Held by the hood bumper bolt - no additional modifications to the bracket.
Held by the hood bumper bolt - no additional modifications to the bracket.
0 2023/07/27 14:02:06
Level from top of expansion tank cap
Level from top of expansion tank cap
0 2023/08/01 13:01:38
Use anything to hold the loop up. Don't bend it any further than necessary to clear the male wedge.
Use anything to hold the loop up. Don't bend it any further than necessary to clear the male wedge.
0 2023/09/04 09:08:06
Look like a MSD and maybe the pink wire is from it??
Look like a MSD and maybe the pink wire is from it??
0 2023/09/05 18:57:39
1. The grommet thru the firewall and pink wire to the 2. ballast resistor. The ballast resistor may have been removed and the pink wire ran to the MSD unit.
1. The grommet thru the firewall and pink wire to the 2. ballast resistor. The ballast resistor may have been removed and the pink wire ran to the MSD unit.
0 2023/09/06 07:02:06
0 2023/09/06 07:02:15
0 2023/09/07 17:37:15
I measured it twice as the photo has a shadow or something that looks like a gap under the end of the rule, but there is not
I measured it twice as the photo has a shadow or something that looks like a gap under the end of the rule, but there is not
0 2023/09/07 17:37:58
This reading is zero Ohms indicating no resistance which is good.
This reading is zero Ohms indicating no resistance which is good.
0 2023/09/08 11:48:21
This upside down horse shoe is called Ohms for resistance measurements with no power on the circuit.
This upside down horse shoe is called Ohms for resistance measurements with no power on the circuit.
0 2023/09/08 11:49:51
If testing the ignition switch, you must turn the switch to each position to test the resistance.
If testing the ignition switch, you must turn the switch to each position to test the resistance.
0 2023/09/08 11:50:55
Jumper at the ignition switch connector with jumper wire. Battery disconnected to install jumper.
Jumper at the ignition switch connector with jumper wire. Battery disconnected to install jumper.
0 2023/09/08 12:15:58
The bulkhead connector is difficult to reach and can be broken if you get to rough.
The bulkhead connector is difficult to reach and can be broken if you get to rough.
0 2023/09/08 12:24:04
This is the key lock cylinder. Put the key in and turn it to the ACC position and you should feel the brass button with the paper clip in the small hole, then push the paper clip in and turn the key counterclockwise a little more and pull out on the lock cylinder.
This is the key lock cylinder. Put the key in and turn it to the ACC position and you should feel the brass button with the paper clip in the small hole, then push the paper clip in and turn the key counterclockwise a little more and pull out on the lock cylinder.
0 2023/09/10 18:09:56
This is the lock housing. If you magnify it, you can see the brass pin that you have to push in.
This is the lock housing. If you magnify it, you can see the brass pin that you have to push in.
0 2023/09/10 18:10:06
To reinstall the lock cylinder, align it in the position that you removed it, ACC and work it inward and then turn it back to OFF. Do not force it.
To reinstall the lock cylinder, align it in the position that you removed it, ACC and work it inward and then turn it back to OFF. Do not force it.
0 2023/09/10 18:10:26