Lethal Performance Grand sport F1A
#1
Burning Brakes
Thread Starter
Member Since: Dec 2010
Location: San Antonio TX
Posts: 831
Likes: 0
Received 0 Likes
on
0 Posts
Lethal Performance Grand sport F1C
We worked pretty hard to finish up a members car that protects our country every day. The customer came to us after he had been left in the cold from another shop that is no longer open and took his hard earned money. He recovered his car and brought it to us and we worked hard inorder to get it to him. We worked with the customer as mush as possible to fix everything we could possibly do inorder to stay within his budget. The car was needing some attention to detail and alot of mistakes had been made when the new drive-line was installed so we corrected as many as possible. The customer wants to see 1000 rwhp from the build the only limiting factor I see is the heads being a LS3. We have made over 900 rwhp with LS3 heads with Ty's car and no coolant loss but tuning will net what we feel is the limit to this. Car does have LS9 gaskets and we didn't have all the specs of the car but she is up and running and the customer got his car back
2008 Corvette Z51
Engine: 408 9:5:1 compression built to handle everything I can throw at it...lol
Procharger F1C w/ 8 rib
Overdrive crank pulley ATI
4 inch S/C pulley
Dewitts Radiator
A&A "Big" intercooler upgrade
205lb Fuel Injector Clinic Injectors (bitch to tune.)
Fuel system can handle anything
Holley fuel rails
RPM Level 6 Trans
Rear end machined for 30 spline input shaft on tranny
Tick master
Monster triple disc
Kooks headers
1 7/8 runners with a 3 inch connector
S pipe jet coated Full Zo6 exhaust
Custom grind Comp Cam specs 227/245@50 115 LSA 637 lift
Brian Tooley 660" Lift Platinum Spring Kit with Titanium Retainers SK001
Rollmaster LS3 Double-Roller Adjustable Timing Set - 4X Cam Gear
LS7 lifters
MGW Shifter
Stock LS3 heads with LS9 head gaskets.
Dual Nozzle Snow performance stage 2 with progressive controller
Custom 3 piece Forza Forged wheelsF- 20X12 and R-20X14
Z06 Seats
Full Grand Sport Body with front splitter
E85
Diff was leaking. Replaced and resealed O ring
Alll cleaned up and ready for service
Other shop cut the fan wiring. We soldered the wiring back together with connector barrels inorder to make sure she had a good connection.
Re did the fuel system wiring as much as possible. Regulator and wiring were not correct and locations where relocated. To protect the wiring as much as possible. Would have preferred to put the controller inside the car.
2008 Corvette Z51
Engine: 408 9:5:1 compression built to handle everything I can throw at it...lol
Procharger F1C w/ 8 rib
Overdrive crank pulley ATI
4 inch S/C pulley
Dewitts Radiator
A&A "Big" intercooler upgrade
205lb Fuel Injector Clinic Injectors (bitch to tune.)
Fuel system can handle anything
Holley fuel rails
RPM Level 6 Trans
Rear end machined for 30 spline input shaft on tranny
Tick master
Monster triple disc
Kooks headers
1 7/8 runners with a 3 inch connector
S pipe jet coated Full Zo6 exhaust
Custom grind Comp Cam specs 227/245@50 115 LSA 637 lift
Brian Tooley 660" Lift Platinum Spring Kit with Titanium Retainers SK001
Rollmaster LS3 Double-Roller Adjustable Timing Set - 4X Cam Gear
LS7 lifters
MGW Shifter
Stock LS3 heads with LS9 head gaskets.
Dual Nozzle Snow performance stage 2 with progressive controller
Custom 3 piece Forza Forged wheelsF- 20X12 and R-20X14
Z06 Seats
Full Grand Sport Body with front splitter
E85
Diff was leaking. Replaced and resealed O ring
Alll cleaned up and ready for service
Other shop cut the fan wiring. We soldered the wiring back together with connector barrels inorder to make sure she had a good connection.
Re did the fuel system wiring as much as possible. Regulator and wiring were not correct and locations where relocated. To protect the wiring as much as possible. Would have preferred to put the controller inside the car.
Last edited by LethalPerformanceTX; 01-05-2014 at 09:16 AM.
#2
Burning Brakes
Thread Starter
Member Since: Dec 2010
Location: San Antonio TX
Posts: 831
Likes: 0
Received 0 Likes
on
0 Posts
Lethal Performance Grand sport F1C
Redid the Meth Nozzles. Did not like the routing or the sealing method used
Much better
Redid the clutch. Spacing was not correct and the slave had to be milled and clearanced. Speed bleeder needed to be notched.
Last edited by LethalPerformanceTX; 01-05-2014 at 08:53 AM.
#3
Burning Brakes
Thread Starter
Member Since: Dec 2010
Location: San Antonio TX
Posts: 831
Likes: 0
Received 0 Likes
on
0 Posts
#4
Thanks a lot Lethal Performance for all the hard work and help. Loving the car everyday. The guys at Lethal Performance are amazing! They sacrificed their own time during the holidays to get me going. They truly put an end to a nightmare. Here are my specs
2008 Corvette Z51
Engine: 408 9:5:1 compression built to handle everything I can throw at it...lol
Procharger F1C w/ 8 rib
Overdrive crank pulley ATI
4 inch S/C pulley
Dewitts Radiator
A&A "Big" intercooler upgrade
205lb Fuel Injector Clinic Injectors (bitch to tune.)
Fuel system can handle anything
Holley fuel rails
RPM Level 6 Trans
Rear end machined for 30 spline input shaft on tranny
Tick master
Monster triple disc
Kooks headers
1 7/8 runners with a 3 inch connector
S pipe jet coated Full Zo6 exhaust
Custom grind Comp Cam specs 227/245@50 115 LSA 637 lift
Brian Tooley 660" Lift Platinum Spring Kit with Titanium Retainers SK001
Rollmaster LS3 Double-Roller Adjustable Timing Set - 4X Cam Gear
LS7 lifters
MGW Shifter
Stock LS3 heads with LS9 head gaskets.
Dual Nozzle Snow performance stage 2 with progressive controller
Custom 3 piece Forza Forged wheelsF- 20X12 and R-20X14
Z06 Seats
Full Grand Sport Body with front splitter
E85
2008 Corvette Z51
Engine: 408 9:5:1 compression built to handle everything I can throw at it...lol
Procharger F1C w/ 8 rib
Overdrive crank pulley ATI
4 inch S/C pulley
Dewitts Radiator
A&A "Big" intercooler upgrade
205lb Fuel Injector Clinic Injectors (bitch to tune.)
Fuel system can handle anything
Holley fuel rails
RPM Level 6 Trans
Rear end machined for 30 spline input shaft on tranny
Tick master
Monster triple disc
Kooks headers
1 7/8 runners with a 3 inch connector
S pipe jet coated Full Zo6 exhaust
Custom grind Comp Cam specs 227/245@50 115 LSA 637 lift
Brian Tooley 660" Lift Platinum Spring Kit with Titanium Retainers SK001
Rollmaster LS3 Double-Roller Adjustable Timing Set - 4X Cam Gear
LS7 lifters
MGW Shifter
Stock LS3 heads with LS9 head gaskets.
Dual Nozzle Snow performance stage 2 with progressive controller
Custom 3 piece Forza Forged wheelsF- 20X12 and R-20X14
Z06 Seats
Full Grand Sport Body with front splitter
E85
#5
Burning Brakes
Thread Starter
Member Since: Dec 2010
Location: San Antonio TX
Posts: 831
Likes: 0
Received 0 Likes
on
0 Posts
Thanks a lot Lethal Performance for all the hard work and help. Loving the car everyday. The guys at Lethal Performance are amazing! They sacrificed their own time during the holidays to get me going. They truly put an end to a nightmare. Here are my specs
2008 Corvette Z51
Engine: 408 9:5:1 compression built to handle everything I can throw at it...lol
Procharger F1C w/ 8 rib
Overdrive crank pulley ATI
4 inch S/C pulley
Dewitts Radiator
A&A "Big" intercooler upgrade
205lb Fuel Injector Clinic Injectors (bitch to tune.)
Fuel system can handle anything
Holley fuel rails
RPM Level 6 Trans
Rear end machined for 30 spline input shaft on tranny
Tick master
Monster triple disc
Kooks headers
1 7/8 runners with a 3 inch connector
S pipe jet coated Full Zo6 exhaust
Custom grind Comp Cam specs 227/245@50 115 LSA 637 lift
Brian Tooley 660" Lift Platinum Spring Kit with Titanium Retainers SK001
Rollmaster LS3 Double-Roller Adjustable Timing Set - 4X Cam Gear
LS7 lifters
MGW Shifter
Stock LS3 heads with LS9 head gaskets.
Dual Nozzle Snow performance stage 2 with progressive controller
Custom 3 piece Forza Forged wheelsF- 20X12 and R-20X14
Z06 Seats
Full Grand Sport Body with front splitter
E85
2008 Corvette Z51
Engine: 408 9:5:1 compression built to handle everything I can throw at it...lol
Procharger F1C w/ 8 rib
Overdrive crank pulley ATI
4 inch S/C pulley
Dewitts Radiator
A&A "Big" intercooler upgrade
205lb Fuel Injector Clinic Injectors (bitch to tune.)
Fuel system can handle anything
Holley fuel rails
RPM Level 6 Trans
Rear end machined for 30 spline input shaft on tranny
Tick master
Monster triple disc
Kooks headers
1 7/8 runners with a 3 inch connector
S pipe jet coated Full Zo6 exhaust
Custom grind Comp Cam specs 227/245@50 115 LSA 637 lift
Brian Tooley 660" Lift Platinum Spring Kit with Titanium Retainers SK001
Rollmaster LS3 Double-Roller Adjustable Timing Set - 4X Cam Gear
LS7 lifters
MGW Shifter
Stock LS3 heads with LS9 head gaskets.
Dual Nozzle Snow performance stage 2 with progressive controller
Custom 3 piece Forza Forged wheelsF- 20X12 and R-20X14
Z06 Seats
Full Grand Sport Body with front splitter
E85
#6
It's all good. Took it out to the 151 meet last night. Felt good to get back out there in the scene. Had a couple pukes out there, but that's normal. Had one guy tell me that he hasn't heard a P1SC sound so good...lmao. Got a grand total of 397 miles on the new motor. Bought new fender inserts and installed them yesterday. No more broke clips and gorrilla glue..lmao. Gonna pick up a new line for the blow off valve, it was fluttering a lot because I have an old line from the last setup that is burnt up from headers. Now that the big stuff is out of the way I can start working on some more small details that need to be addressed.
#7
Safety Car
Looking forward to what it makes.
#10
Instructor
Danny took care of me when i was there a few months ago, him and his crew went above and beyond...
Depending on the thickness of my wallet I'll hafta see what they can do about getting my car back on the road lol..
Setup looks awesome man - congrats
Depending on the thickness of my wallet I'll hafta see what they can do about getting my car back on the road lol..
Setup looks awesome man - congrats
#15
Le Mans Master
Nice job fixing their mess, It's always a pain to redo another shops screw up. I heard about the cops at his apartment the other morning check serial numbers. They thought it was my Z because of the red wheels.
#19
Race Director
I finally settled in on them about seven years ago after doing business with several other shops. Back then, like this thread, Lethal worked their magic on my C5 that another shop had half-a$$ed. Danny and Lethal have gone above and beyond with customer service to me and my friends.
Now how much more nut swinging do I have to do to get a discount on that TT kit bro or at least a free nights stay at the casa with the next round of mods
#20
Nice job Lethal! No surprise here though i know how the Lethal Crew gets down, they always treat me and my friends great,and do dam good job, i wouldn't take my car anywhere else!
Congrats to the Owner of the Grand sport, sick car!
Congrats to the Owner of the Grand sport, sick car!