Houston engine builders
#1
Le Mans Master
Thread Starter
Houston engine builders
Anyone familair with Houston Enigne and Balancing service.
http://www.houstonengine.com/#ContactInformation
They seem to know their stuff. A lot drag racing winners.
Local opinions?
http://www.houstonengine.com/#ContactInformation
They seem to know their stuff. A lot drag racing winners.
Local opinions?
#2
Pro
Anyone familair with Houston Enigne and Balancing service.
http://www.houstonengine.com/#ContactInformation
They seem to know their stuff. A lot drag racing winners.
Local opinions?
http://www.houstonengine.com/#ContactInformation
They seem to know their stuff. A lot drag racing winners.
Local opinions?
Westside.Performance.And.Machine.Inc.713-465-7996
Been usig Them for years
BuffaloBILL
#3
Tech Contributor
Anyone familair with Houston Enigne and Balancing service.
http://www.houstonengine.com/#ContactInformation
They seem to know their stuff. A lot drag racing winners.
Local opinions?
http://www.houstonengine.com/#ContactInformation
They seem to know their stuff. A lot drag racing winners.
Local opinions?
#4
Race Director
Member Since: Jan 2000
Location: Corsicana, Tx
Posts: 12,616
Received 1,877 Likes
on
915 Posts
2020 C2 of the Year - Modified Winner
2020 Corvette of the Year (performance mods)
C2 of Year Winner (performance mods) 2019
2017 C2 of Year Finalist
That was Tommy Costales way back when. Good stuff. Westside is good also...
I would also strongly recommend G&G Machine up near Tomball. Great little shop that takes pride on what they do. Ask for Joe and tell him you're *another* Vette guy that Jim sent by. He's been doing a lot of work for us with no complaints from anyone. Good pricing, gets it done when he says he will. No machine shop jail!
JIM
I would also strongly recommend G&G Machine up near Tomball. Great little shop that takes pride on what they do. Ask for Joe and tell him you're *another* Vette guy that Jim sent by. He's been doing a lot of work for us with no complaints from anyone. Good pricing, gets it done when he says he will. No machine shop jail!
JIM
#5
Burning Brakes
Houston E & B is one of the best shops in the area in one of the crappiest neighborhoods. He's also the go-to guy for most of the serious drag racers in this area. I personally know 3 of the people on that customer list and they win a lot of races. His work isn't cheap but quality work never is.
Tommy's dad Luther was a legend around here when I was a kid. I don't know if any of the Houston guys remember the old Invader 57 T-bird drag car that ran at the old drag strip on I-45 over 30 years ago. I think that was Tommy's first drag car. He's ran a 67 Corvette in Super Gas for at least 25 years.
Tommy's dad Luther was a legend around here when I was a kid. I don't know if any of the Houston guys remember the old Invader 57 T-bird drag car that ran at the old drag strip on I-45 over 30 years ago. I think that was Tommy's first drag car. He's ran a 67 Corvette in Super Gas for at least 25 years.
Last edited by BLee; 02-14-2011 at 09:28 AM.
#6
Burning Brakes
That was Tommy Costales way back when. Good stuff. Westside is good also...
I would also strongly recommend G&G Machine up near Tomball. Great little shop that takes pride on what they do. Ask for Joe and tell him you're *another* Vette guy that Jim sent by. He's been doing a lot of work for us with no complaints from anyone. Good pricing, gets it done when he says he will. No machine shop jail!
JIM
I would also strongly recommend G&G Machine up near Tomball. Great little shop that takes pride on what they do. Ask for Joe and tell him you're *another* Vette guy that Jim sent by. He's been doing a lot of work for us with no complaints from anyone. Good pricing, gets it done when he says he will. No machine shop jail!
JIM
Joe
I have my new G&G 383 'spare' sitting in the corner ready to go when one of our guys break something.
#7
Le Mans Master
Thread Starter
At least your paying for skill and not overhead.
You are right just an old gas station. Very unassuming shop.
Man, the economic downturn has hit that area real hard. do
He balanced my flywheel and pressure plate. I was impressed by his skill.
I am going to have him unshroud my valves and pin the studs.
But I may have him build me a stroker motor down the line.
Compared to a mail order or crate engine. I think I would get a more precise build for my money.
#8
Le Mans Master
Thread Starter
Westside are nice guys. Seem to know their stuff and they have an engine dyno!
They are going to
unshroud my valves
extend my pushrod slots for 1.6 rockers
install screw in studs (they appear to be press in for a stock look)
pocket port the 461s.
Pretty reasonable price and ready by end of this coming week.
Last edited by MiguelsC2; 02-20-2011 at 03:36 AM.