So, you are retired. What did you do today with your C1 or C2 ?
#81
Safety Car
Haven’t done much to the 61 in the last few days. Watched it in the back ground as I worked on another project. So far I’ve bored it .125” over, 3 angle valve job with slightly larger 1.600” Chevy valves, modified the oil system to full flow from the original partial flow where it filtered some oil at the end of the line. We are having the 4.000” stroke Mercury crank ground and balanced. Several other mods are in the works as time permits. I’ll be installing a 409 Chevy water pump, sbc harmonic damper and pulleys, AC compressor, power steering, and alternator. I'm going to fit modern one piece seals on the crank instead of the junk rope seals. This will be a pretty nice piece of eye candy when done.
I know it’s not a Corvette but at least I’m getting some Chevy parts in it.
I know it’s not a Corvette but at least I’m getting some Chevy parts in it.
Last edited by Robert61; 06-19-2018 at 11:38 PM.
The following 2 users liked this post by Robert61:
59BlueSilver (06-19-2018),
6T7L71CPE (06-19-2018)
#82
Intermediate
Due to health issues for the last couple of years retirement is not going to be quite what I had planned for. So today I moved my c-1 out to the road and put a for sale in the window.
#83
Safety Car
That sucks. I hope you prevail in whatever it is.
#86
Team Owner
I was all set to tackle it solo but when I told the wife you had offered to do it; she said, "....are you nuts, get the car the hell over to Mark!"
She's watched me work on cars for 50 years and knows it ain't pretty...what with the blood and the cursing and tools thrown across the garage....
Last edited by Frankie the Fink; 06-20-2018 at 04:06 AM.
#87
And I'm damned glad you did !!!
I was all set to tackle it solo but when I told the wife you had offered to do it; she said, "....are you nuts, get the car the hell over to Mark!"
She's watched me work on cars for 50 years and knows it ain't pretty...what with the blood and the cursing and tools thrown across the garage....
I was all set to tackle it solo but when I told the wife you had offered to do it; she said, "....are you nuts, get the car the hell over to Mark!"
She's watched me work on cars for 50 years and knows it ain't pretty...what with the blood and the cursing and tools thrown across the garage....
The following users liked this post:
Frankie the Fink (06-20-2018)
#88
Race Director
Member Since: Jun 2006
Location: Inverness FL
Posts: 17,891
Received 727 Likes
on
621 Posts
St. Jude Donor '07
used the 62's trunk to lay out the tools to change the windshield wiper motor in the caravan...
doesn't get driven much anymore...
Bill
doesn't get driven much anymore...
Bill
Last edited by wmf62; 06-20-2018 at 07:36 AM.
#90
Enjoy while you can.
Thread Starter
Member Since: May 2008
Location: 10th District Court OHIO
Posts: 17,170
Received 2,686 Likes
on
1,273 Posts
Ohio Events Coordinator
2023 C8 of the Year Finalist - Unmodified
2022 C2 of the Year Finalist - Unmodified
C2 of Year Finalist (stock) 2019
St. Jude Donor '14-'15-'16-'17-‘18-'19-'20-'21-'22-'23-'24
12th day of retirement and I haven't found the time or good weather to take the sweet silver out for a ride
#91
Been retired for 8 years sold the corvette got the RV ready to roll .
#92
Enjoy while you can.
Thread Starter
Member Since: May 2008
Location: 10th District Court OHIO
Posts: 17,170
Received 2,686 Likes
on
1,273 Posts
Ohio Events Coordinator
2023 C8 of the Year Finalist - Unmodified
2022 C2 of the Year Finalist - Unmodified
C2 of Year Finalist (stock) 2019
St. Jude Donor '14-'15-'16-'17-‘18-'19-'20-'21-'22-'23-'24
Finally, got the sweet silver out for a spin and back home for a wash.
#93
Team Owner
I put in an electric fuel pump under the tank on the 63 to fend off the vapor lock from Orlando summer heat.....its supposed to work well but the little SOB is noisy. Operated via side panel push button switch...
#94
Interesting what is the Pressure of that pump I see you cushion the pump thru the tank any vibration to cockpit
#95
Team Owner
The pump is the Sundely 12V 4-6 psi pump.... After comparing to a bunch of small, low pressure pumps this one had the longest expected life and appropriate pressure and would fit where I wanted it -- Amazon has them...
No vibration, but with the key on and engine not running you sure hear it... Of course, that might be lessened when I get the spare tire tub installed again...
No vibration, but with the key on and engine not running you sure hear it... Of course, that might be lessened when I get the spare tire tub installed again...
#96
Melting Slicks
The pump is the Sundely 12V 4-6 psi pump.... After comparing to a bunch of small, low pressure pumps this one had the longest expected life and appropriate pressure and would fit where I wanted it -- Amazon has them...
No vibration, but with the key on and engine not running you sure hear it... Of course, that might be lessened when I get the spare tire tub installed again...
No vibration, but with the key on and engine not running you sure hear it... Of course, that might be lessened when I get the spare tire tub installed again...
#97
Le Mans Master
Previously, I stripped everything to bare glass and removed the flares. Yesterday I shot everything with 3 coats of epoxy primer. Taking today off to rest my weary bones before the real work starts.
The following users liked this post:
BlackMoon (11-24-2018)
#98
Melting Slicks
Did you use "flare repair" panels or full quarters? Got any progress pictures of the repairs? Thanks