FS: C2 New Frame, Birdcage, Engine, Transmission
#1
Drifting
Thread Starter
C2 New Frame, Partial Birdcage, 327/350 Engine, 4 Spd Transmission
New Vette Products C2 frame. No VIN number. C2 with BBC dimple.SOLD
Partial birdcage. Coupe cage with the roof hoop removed. SOLD
ENGINE AND TRANSMISSION ARE SOLD.
Thanks, Walt.
Partial birdcage. Coupe cage with the roof hoop removed. SOLD
ENGINE AND TRANSMISSION ARE SOLD.
Thanks, Walt.
Last edited by Vogie; 11-19-2018 at 03:22 PM. Reason: Engine Sold
The following users liked this post:
Wjkiefiuk@comcast.ne (02-15-2018)
#4
Drifting
Thread Starter
I will sell these separately or in any combination. The price quoted is the "back up to the door and clear the shop" price. With four items there is approximately 64 possible combinations and prices so compliance with forum rules to the letter of the law will be difficult.
Last edited by Vogie; 02-10-2018 at 08:52 PM.
#6
Drifting
Thread Starter
#10
c2 parts karl 330-620-3302
New Vette Products C2 frame. No VIN number. C2 with BBC dimple. Coupe, but easily made roadster by adding two body mounts. Per the Chevrolet Performance Manual: full perimeter seam welded, lower control arm mounts gusseted, engine mount horns boxed. Center crossmember converted to C3 removable unit (included). After market GM200R4 crossmember included. Gloss black powder coat by Van Steel. Never installed under a body.
Partial birdcage. Coupe cage with the roof hoop removed. Fair shape (excellent according to David Crane in California - NOT). Windshield posts okay. Dash area is good, front door posts are good, sills are good. Z-bar missing. Entire cage as is.
327/350 engine from my 1966. TI distributor. All accessories (not known if original alternator and carb). Flywheel and clutch. Ignition shielding not complete. Receipt for engine work done for previous owner years ago. Running when removed from my car. Stored for 10+ years.
Four speed transmission from my 1966. Includes bell housing and shifter. Still attached to the engine.
Available for inspection on request. Will provide photos to serious inquirers. PLEASE! ATTENTION! Contact me by email at wvogelgesang at tampabay dot rr dot com. I am not a frequent visitor so PMs may sit unanswered for a long while.
$7500.00 or reasonable offer
All located in Seffner, Florida (in the Tampa Bay area). I can deliver within the Central Florida area. Buyers out of central Florida will have to arrange transport or shipping.
Thanks, Walt.
Partial birdcage. Coupe cage with the roof hoop removed. Fair shape (excellent according to David Crane in California - NOT). Windshield posts okay. Dash area is good, front door posts are good, sills are good. Z-bar missing. Entire cage as is.
327/350 engine from my 1966. TI distributor. All accessories (not known if original alternator and carb). Flywheel and clutch. Ignition shielding not complete. Receipt for engine work done for previous owner years ago. Running when removed from my car. Stored for 10+ years.
Four speed transmission from my 1966. Includes bell housing and shifter. Still attached to the engine.
Available for inspection on request. Will provide photos to serious inquirers. PLEASE! ATTENTION! Contact me by email at wvogelgesang at tampabay dot rr dot com. I am not a frequent visitor so PMs may sit unanswered for a long while.
$7500.00 or reasonable offer
All located in Seffner, Florida (in the Tampa Bay area). I can deliver within the Central Florida area. Buyers out of central Florida will have to arrange transport or shipping.
Thanks, Walt.
#16
Race Director
Member Since: Mar 2009
Location: Canada's capital
Posts: 19,777
Received 4,583 Likes
on
2,157 Posts
2020 Corvette of the Year Finalist (appearance mods)
C1 of Year Finalist (appearance mods) 2019
Bump for you......hell of a deal for the engine/trans combo.
#17
Melting Slicks
Hey there fellow Corvetter's I echo Kerrmudgeon's thoughts on the frame. I purchased one of these for my '66 BB several years ago and have not looked back. The frame of my '66 was partially toasted, why put untold sums of $$$ into a toasted frame only to be able to say "it has it's original frame"......yes with about a million patches to keep it together".....lol. My car has been NCRS judged twice receiving a 97.2 last time out. Not one call out was made regarding the frame.....and that's what I got to say about that.
Quite honestly am surprised the frame is still available.
Quite honestly am surprised the frame is still available.
#18
Administrator
Member Since: Jul 2000
Location: About 1100 miles from where I call home. Blue lives matter.
Posts: 51,414
Received 5,331 Likes
on
2,775 Posts
Hey there fellow Corvetter's I echo Kerrmudgeon's thoughts on the frame. I purchased one of these for my '66 BB several years ago and have not looked back. The frame of my '66 was partially toasted, why put untold sums of $$$ into a toasted frame only to be able to say "it has it's original frame"......yes with about a million patches to keep it together".....lol. My car has been NCRS judged twice receiving a 97.2 last time out. Not one call out was made regarding the frame.....and that's what I got to say about that.
Quite honestly am surprised the frame is still available.
Quite honestly am surprised the frame is still available.
#19
Team Owner
Member Since: Aug 2008
Location: Rochester NY
Posts: 31,358
Received 5,010 Likes
on
2,529 Posts
St. Jude Donor '09-'10-'11-'12-'13-'14-'15-'16-'17-'18-‘19-'20-'21-'22-'23-'24
The following users liked this post:
Chummy85623 (05-06-2018)
#20
Melting Slicks