Custom Corvette Garage Art
Thread Starter
Former Vendor
Joined: Apr 2015
Posts: 95
Likes: 0
From: Colorado
Custom Corvette Garage Art
Seems there is a good amount of interest in these so I'll go ahead and put this out there.
I custom pick the wood (or Acrylic), design from scratch, draw, and then engrave and paint fill. I finish it up with a metal frame, hangers and wire. It takes me an average of 2-3 weeks from design to shipping.
The wood pcs start at 400 and the acrylic pcs start at 325 (I have white acrylic as well that we can paint fill the engraving black). This includes your choice for the metal frame, stain color if we go with wood, shipping in the US, and of course as many proofs as it takes to get the design right. The pcs are 24”X18” plus or minus an inch with the frame and how the woodworking turns out.
Suggestions and input are always welcome and helpful to me! We can do any kind of customization from wood type to different designs.
These really will make your garage/office/living room standout! Or use it to put on display at shows.
Shoot me a PM or email to get started!
I custom pick the wood (or Acrylic), design from scratch, draw, and then engrave and paint fill. I finish it up with a metal frame, hangers and wire. It takes me an average of 2-3 weeks from design to shipping.
The wood pcs start at 400 and the acrylic pcs start at 325 (I have white acrylic as well that we can paint fill the engraving black). This includes your choice for the metal frame, stain color if we go with wood, shipping in the US, and of course as many proofs as it takes to get the design right. The pcs are 24”X18” plus or minus an inch with the frame and how the woodworking turns out.
Suggestions and input are always welcome and helpful to me! We can do any kind of customization from wood type to different designs.
These really will make your garage/office/living room standout! Or use it to put on display at shows.
Shoot me a PM or email to get started!
Thread Starter
Former Vendor
Joined: Apr 2015
Posts: 95
Likes: 0
From: Colorado
Hey guys I'm going to run a sale on these, as I haven't even paid off the cost to be a sponsor here yet.
250.00 for a piece that is engraved on either white or black acrylic. This includes the custom drawing, frame, and shipping.
325.00 for a wood alder piece with your choose of stain color, custom drawing, frame and shipping.
*** I custom draw each of these, if you have a photo of your car we can use that***
250.00 for a piece that is engraved on either white or black acrylic. This includes the custom drawing, frame, and shipping.
325.00 for a wood alder piece with your choose of stain color, custom drawing, frame and shipping.
*** I custom draw each of these, if you have a photo of your car we can use that***
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Instructor
Joined: Sep 2014
Posts: 149
Likes: 3
From: Downingtown PA
Laser engravers are wonderful things. Wish I had room in the shop for one! If you have a countertop fitter near you, see if you can grab scrap pieces of solid surface material like Corian. It should engrave as well as plexiglass - and would give your stuff another level of finish.
Thread Starter
Former Vendor
Joined: Apr 2015
Posts: 95
Likes: 0
From: Colorado
Laser engravers are wonderful things. Wish I had room in the shop for one! If you have a countertop fitter near you, see if you can grab scrap pieces of solid surface material like Corian. It should engrave as well as plexiglass - and would give your stuff another level of finish.
I actually have a few granite and countertop guys that set aside stuff for me, but the acrylic gives the best finish when engraved. Plus I'm able to cut the acrylic as well with the laser.
