FS: Small Block 350/430 HP Custom Pro Built Turn Key Engine
#1
FS: Small Block 350/430 HP Custom Pro Built Turn Key Engine $7K OBO
I've got a brand new, professionally built 350/430 HP engine. I bought the engine for a '72 project but due to an impending move I'm going to need to walk from my project and try to recoup some expenses.
I've got receipts for $9K invested in the engine build. Will let it go for $7K and I'm open to reasonable offers. Motivated seller here. I also have a video of run tests so you can verify condition. It has never been installed in a car and is on a pallet ready to ship. Located about 30 minutes east of St Louis. I can provide details and all paperwork from the purchase.
Everything is new. Here's the details:
--March Serpentine Belt System (W/ Alternator, AC Compressor, Power Steering Pump)
--Mini High Torque Starter
--Braided Fuel Lines
--4 Bolt Main Full Round Seal Block
--10:1 Compression pistons
--Speed Pro Moly Rings
--Hydraulic Roller Camshaaft
--Melling 3 Piece timing set
--Clevite Trimetal Engine Bearings
--Melling High Pressure Oil Pump # M55HP
--Edelbrock Aluminum Heads With 64cc Combustion Chambers
--2.02" Stainless Steel Intake Valves
--1.60" Stainless Exhaust Valves
--Pushrods, Guide Plates, and Roller Rocker Arms
--Pushrods, Guide Plates, and Roller Rocker Arms
--Edelbrock Air Gap Intake Manifold #7501
--Edelbrock 650 CFM Thunder Series Carburetor
--MSD HEI Distributor With 53,000 Volt Coil
--Champion Spark Plugs & Taylor Ignition Wires, Electric Choke Assembly
I've got receipts for $9K invested in the engine build. Will let it go for $7K and I'm open to reasonable offers. Motivated seller here. I also have a video of run tests so you can verify condition. It has never been installed in a car and is on a pallet ready to ship. Located about 30 minutes east of St Louis. I can provide details and all paperwork from the purchase.
Everything is new. Here's the details:
--March Serpentine Belt System (W/ Alternator, AC Compressor, Power Steering Pump)
--Mini High Torque Starter
--Braided Fuel Lines
--4 Bolt Main Full Round Seal Block
--10:1 Compression pistons
--Speed Pro Moly Rings
--Hydraulic Roller Camshaaft
--Melling 3 Piece timing set
--Clevite Trimetal Engine Bearings
--Melling High Pressure Oil Pump # M55HP
--Edelbrock Aluminum Heads With 64cc Combustion Chambers
--2.02" Stainless Steel Intake Valves
--1.60" Stainless Exhaust Valves
--Pushrods, Guide Plates, and Roller Rocker Arms
--Pushrods, Guide Plates, and Roller Rocker Arms
--Edelbrock Air Gap Intake Manifold #7501
--Edelbrock 650 CFM Thunder Series Carburetor
--MSD HEI Distributor With 53,000 Volt Coil
--Champion Spark Plugs & Taylor Ignition Wires, Electric Choke Assembly
Last edited by YoJoeNCSU; 11-22-2016 at 05:47 AM.
#5
Race Director
Member Since: Nov 2006
Location: Athens GA
Posts: 19,446
Received 351 Likes
on
304 Posts
St. Jude Donor '12-'13, '15- '16-'17-'18-'19, '21
FYI...forum rules require you to put a price on it.
Of course you can also state OBO once you post the price.
Otherwise mods will pull your ad...
Good Luck With Sale (GLWS)
Bman
Of course you can also state OBO once you post the price.
Otherwise mods will pull your ad...
Good Luck With Sale (GLWS)
Bman
#6