Emission part for a 1980.
Aug 30, 2008 | 03:19 AM
Thread Starter
Racer
Joined: Feb 2007
Posts: 290
Likes: 0
From: Winchester CA
Emission part for a 1980.
I need an EFE tube for my '80. Any suggestions where I can find one? I have already tried: dealer, Ebay and Craig's List.
Thanks in advance!
Aug 30, 2008 | 04:13 AM
Le Mans Master
Joined: Sep 2002
Posts: 5,236
Likes: 898
From: Myrtle Beach SC
Carlisle would have been perfect but that was last week. Give Rik's Corvette a try...they deal with used parts. Thought I've seen those on eBay before
http://www.riksvet.com/
Aug 30, 2008 | 09:00 AM
Race Director
Joined: May 2006
Posts: 16,528
Likes: 53
From: Dayton, Ohio
Quote:
Originally Posted by
c3corvettes
I need an EFE tube for my '80. Any suggestions where I can find one? I have already tried: dealer, Ebay and Craig's List.
Thanks in advance!
EFE tube ??? need more info- possibly a picture or illustration.
Aug 30, 2008 | 02:04 PM
Burning Brakes
Joined: Aug 2006
Posts: 1,155
Likes: 0
From: San Diego California
Quote:
Originally Posted by
hunt4cleanair
Carlisle would have been perfect but that was last week. Give Rik's Corvette a try...they deal with used parts. Thought I've seen those on eBay before
http://www.riksvet.com/
I would also try J&D Corvette.
Aug 31, 2008 | 01:00 PM
Intermediate
Joined: Nov 2005
Posts: 47
Likes: 0
From: Clifton VA
Emissions Parts
This guy had all the parts pump, tubes, brackets etc.- restored to original condition - that I needed for a '79. Believe his name is Bill Hodel. Advertises in Hemmings. I will send contact info if I can find the paperwork.
Aug 31, 2008 | 02:26 PM
Intermediate
Joined: Nov 2005
Posts: 47
Likes: 0
From: Clifton VA
330-832-0871 if # is still good
Aug 31, 2008 | 10:26 PM
Race Director
Joined: Apr 2000
Posts: 17,676
Likes: 201
From: Who says "Nothing is impossible" ? I've been doing nothing for years.
Think I'm missing it on my '80 too
Sep 1, 2008 | 03:03 AM
Thread Starter
Racer
Joined: Feb 2007
Posts: 290
Likes: 0
From: Winchester CA
Quote:
Originally Posted by
DWncchs
EFE tube ??? need more info- possibly a picture or illustration.
It's a pre-bent tube that connects the exhaust valve that's located at the bottom of the right side exhaust opening to a ported vacuum switch on the the thermostat housing.
10 Ugly Corvettes That We Still Kinda Love
Joe Kucinski
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Sep 1, 2008 | 03:04 AM
Thread Starter
Racer
Joined: Feb 2007
Posts: 290
Likes: 0
From: Winchester CA
Quote:
Originally Posted by
ray79
330-832-0871 if # is still good
Ray79, thanks!
Sep 1, 2008 | 03:07 AM
Thread Starter
Racer
Joined: Feb 2007
Posts: 290
Likes: 0
From: Winchester CA
Quote:
Originally Posted by
MotorHead
Think I'm missing it on my '80 too
Yeah, I think your engine needs it.
That is a very impressive setup you have there. Very nice '80 by the way.
Jan 4, 2009 | 05:43 AM
Thread Starter
Racer
Joined: Feb 2007
Posts: 290
Likes: 0
From: Winchester CA
I haven't had any luck locating this part...
Jan 4, 2009 | 08:03 AM
Intermediate
Joined: Sep 2007
Posts: 40
Likes: 0
From: Dallas