AmericanRacingHeaders adds an "LS SWAP" header for the C3 owners................PICS
02-06-2014, 10:52 PM
#82
Premium Supporting Vendor
Thread Starter
We have already installed a few sets of the C3 LS headers.
Some people are using "homemade" or oddball motor mounts.
These are already fit and proven.
Some people are using "homemade" or oddball motor mounts.
These are already fit and proven.
02-07-2014, 03:53 PM
#86
Premium Supporting Vendor
Thread Starter
Chris, Thanks for the order
Hi Jim, we installed the BBC headers on your '70?
Eric, Thanks for the order
Moving out quite a few C3 LS swap headers, we also have SBC headers.
You already installed the exhaust, you can offer a full kit Just got off the phone with Steve to begin my order.
My combo is as follows
LS3
Dirty Dingo sliders
4L80E trans
Borgeson Box
I have a thread going on here that has not been updated in a few months due to slow progress but I have the car scheduled to start the motor swap in 4 weeks so hopefully thing will begin moving forward quickly and I can post up more photos.
Thanks Steve, it was good talking to you about the headers and I look forward to seeing these on the car!
My combo is as follows
LS3
Dirty Dingo sliders
4L80E trans
Borgeson Box
I have a thread going on here that has not been updated in a few months due to slow progress but I have the car scheduled to start the motor swap in 4 weeks so hopefully thing will begin moving forward quickly and I can post up more photos.
Thanks Steve, it was good talking to you about the headers and I look forward to seeing these on the car!
Moving out quite a few C3 LS swap headers, we also have SBC headers.
02-11-2014, 02:41 PM
#87
Premium Supporting Vendor
Thread Starter
Please note:
These headers are already PROVEN to fit with the noted combinations in the first thread.
A few of you have pointed out that this thread may make the headers in "development mode", this is NOT the case.
Thanks very much.
These headers are already PROVEN to fit with the noted combinations in the first thread.
A few of you have pointed out that this thread may make the headers in "development mode", this is NOT the case.
Thanks very much.
02-11-2014, 10:30 PM
#88
Drifting
My setup:
Custom Image Corvette motor mount plates (engine in original location)
Flaming River Rack
LS3 motor
Keisler RS500 tranny
Hydraulic Clutch
Custom Image Corvette motor mount plates (engine in original location)
Flaming River Rack
LS3 motor
Keisler RS500 tranny
Hydraulic Clutch
Last edited by CWerner; 02-12-2014 at 09:02 AM.
02-12-2014, 07:12 AM
#90
Race Director
I'm waiting for pictures of installations. Motor mount placement is obviously key to how these fit. Anyone have pictures of these headers installed and what are you using for mounts and locations of the motor.
02-12-2014, 11:09 AM
#93
Premium Supporting Vendor
Thread Starter
We just rec'd another 20,000 lbs of 304 Stainless Steel, January was a record month overall despite the brutal storms here in the Northeast.
Bottom Line, These should be down in TEXAS by next week.
02-16-2014, 09:11 AM
#96
Melting Slicks
02-19-2014, 03:00 PM
#98
Premium Supporting Vendor
Thread Starter
Sidepipes, yes.
Only in-house here in NEW YORK at this time for complete sidepipes.
We can supply the bends to allow our swap headers to work with existing sidepipes.
Thank You
Only in-house here in NEW YORK at this time for complete sidepipes.
We can supply the bends to allow our swap headers to work with existing sidepipes.
Thank You
02-19-2014, 03:00 PM
#99
Premium Supporting Vendor
Thread Starter
Sidepipes, yes.
Only in-house here in NEW YORK at this time for complete sidepipes.
We can supply the bends to allow our swap headers to work with existing sidepipes.
Thank You
Only in-house here in NEW YORK at this time for complete sidepipes.
We can supply the bends to allow our swap headers to work with existing sidepipes.
Thank You
