Flexplate gear question
Thread Starter
Burning Brakes
Joined: Oct 2002
Posts: 813
Likes: 0
From: death to the southeast
Flexplate gear question
Is there a way to tell if your flexplaye and starter bendex have the correct number of teeth? What number teeth with the flexplate should match with the bendex?
Race Director
Joined: Nov 2000
Posts: 11,872
Likes: 12
From: Waterloo ontario Canada
Re: Flexplate gear question (Teuffelhunde)
I didn't know it mattered. For my bigblock I require 168 teeth in order for the flywheel and starter motor to engage properly. If I put a 157 tooth flywheel on the starter would be too far away to mesh.
When I put my mini starter on I wanted to check this mesh so I just pried the starter drive out and into the flywheel. If they seem to mesh fine don't worry about the tooth count.
Hope this helps
When I put my mini starter on I wanted to check this mesh so I just pried the starter drive out and into the flywheel. If they seem to mesh fine don't worry about the tooth count.
Hope this helps
Burning Brakes
Joined: Dec 2000
Posts: 962
Likes: 0
From: Carlisle PA
Re: Flexplate gear question (Teuffelhunde)
If I remember right with a mini starter (Powermaster), there are two sets of mounting holes that would mount to the block. One Part # fit both size flywheels. One set of holes was for the large flywheel, another set for the smaller flywheel.
Team Owner
Joined: Jun 2001
Posts: 23,375
Likes: 1,067
From: Virginia USA
Re: Flexplate gear question (70PurpleLS7)
This is for manual tranny flywheels so I am not sure if it applies to flexplates:
Flywheels with two different diameters are used on Chevrolet small-block V8, big-block V8, and V6/90° engines. Large flywheels are 14" in diameter, and have 168 teeth on the starter ring gear. Small diameter flywheels are 12-3/4" in diameter and have 153 teeth on the starter ring gear.
The difference in flywheel diameters requires two distinct starter housings. Starter noses used with large diameter flywheels have two offset bolt holes; starters for small flywheels have two bolt holes which are parallel to the back of the block. Most Chevrolet blocks are drilled for both types of starters. If you are changing the diameter of your Chevrolet's flywheel, you can convert your present starter to fit the new flywheel by installing the appropriate starter nose, starter motor housing, found within each engine classification. You will have to note which starter nose you have and change it accordingly.
Hope this helps
John
Flywheels with two different diameters are used on Chevrolet small-block V8, big-block V8, and V6/90° engines. Large flywheels are 14" in diameter, and have 168 teeth on the starter ring gear. Small diameter flywheels are 12-3/4" in diameter and have 153 teeth on the starter ring gear.
The difference in flywheel diameters requires two distinct starter housings. Starter noses used with large diameter flywheels have two offset bolt holes; starters for small flywheels have two bolt holes which are parallel to the back of the block. Most Chevrolet blocks are drilled for both types of starters. If you are changing the diameter of your Chevrolet's flywheel, you can convert your present starter to fit the new flywheel by installing the appropriate starter nose, starter motor housing, found within each engine classification. You will have to note which starter nose you have and change it accordingly.
Hope this helps
John
Thread Starter
Burning Brakes
Joined: Oct 2002
Posts: 813
Likes: 0
From: death to the southeast
Re: Flexplate gear question (Teuffelhunde)
I'll try pulling out the bendex and fitting it to the flywheel. Any one have ideas on why the starter wouldn't spin the flywheel and just grinds? I tried shimming the outer bolt with 2 washers and still have the problem. Any idea will help!!
Le Mans Master
Joined: Jul 2001
Posts: 9,622
Likes: 16
From: absecon nj
Re: Flexplate gear question (theandies)
thats why i asked on your previous post which starter bolt pattern you had on there. :yesnod: I rebuilt starters and alternators for 5 years,ive seen all kinds. :D
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski